Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM(w/ Differential Lock) › from 2016.01
RM3270E _52 Drivetrain _041686 AXLE AND DIFFERENTIAL _0248598 DIFFERENTIAL SYSTEM(w/ Differential Lock) C

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  P17CC  Rear Differential Lock Control SW Stuck ON  


DESCRIPTION

This DTC is output when a malfunction of the differential lock switch is detected.

DTC No. Detection Item DTC Detection Condition Trouble Area
P17CC Rear Differential Lock Control SW Stuck ON
·

Diagnosis Condition: Directly after the ignition switch is turned to ON, or when the ignition switch is ON

·

Malfunction Status: Differential lock switch stuck ON

·

Malfunction Time: 0.3 seconds or more when the ignition switch is turned to ON, or 60 seconds or more with the ignition switch ON

·

Other: 1 trip detection logic


·

Wire harness and connector

·

4 wheel drive control ECU

·

Differential lock switch



WIRING DIAGRAM

C325715E04
1.313,2.792 3.74,2.99 2.427,0.198 10 false Differential Lock Switch 1.292,2.573 1.75,2.771 0.458,0.198 10 false G58 1.469,1.958 1.625,2.156 0.156,0.198 10 false 3 3.177,1.948 3.333,2.146 0.156,0.198 10 false 6 4.969,2.854 5.427,3.052 0.458,0.198 10 false C60 4.969,3.073 6.729,3.26 1.76,0.188 10 false 4 Wheel Drive Control ECU 5,1.938 5.156,2.135 0.156,0.198 10 false R 4.74,1.927 5.052,2.125 0.313,0.198 10 false 15 5.979,1.063 6.292,1.26 0.313,0.198 10 false IG 1.667,1.958 1.823,2.156 0.156,0.198 10 false E 3,1.948 3.156,2.146 0.156,0.198 10 false B

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - DIFFERENTIAL LOCK SWITCH)
a.

Disconnect the C60 4 wheel drive control ECU connector.


b.

Disconnect the G58 differential lock switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C60-15 (R) or G58-6 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT DIFFERENTIAL LOCK SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT DIFFERENTIAL LOCK SWITCH
a.

Disconnect the G58 differential lock switch connector.


b.
C326164C04
1.438,1.219 0.99,1.729 false 2,1.229 2.51,1.698 false 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 0.927,1.74 1.083,1.938 0.156,0.198 10 false B 2.531,1.74 2.688,1.938 0.156,0.198 10 false E
*a Component without harness connected
(Differential Lock Switch)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (B) - 3 (E) Switch not pressed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG