Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › from 2016.01
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205105 BACK DOOR A

DOOR / HATCH  BACK DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 68920 1.INSTALL POWER BACK DOOR UNIT SET ASSEMBLY LH (w/ Power Back Door)

NOTICE:

Do not apply any horizontal load to the power back door unit set assembly in order to prevent the piston rod from deforming.


a.

Clean the bolt hole on the vehicle body and back door panel.


b.
B438685C04
0.396,0.958 0.479,0.958 0.479,0.958 0.573,0.813 false 0.198,0.865 0.51,1.063 0.313,0.198 10 false *a 2.167,0.99 2.323,1.188 0.156,0.198 10 true 1 3.115,0.979 3.271,1.177 0.156,0.198 10 true 2 2.031,3.146 2.188,3.344 0.156,0.198 10 true 1 1.948,2.5 2.104,2.698 0.156,0.198 10 true 2
*a Grommet


Temporarily install the power back door unit set assembly.


c.

Tighten 4 new bolts to install the power back door unit set assembly.

NOTICE:

Install the power back door unit set assembly while supporting the back door by hand.


HINT:

Tighten the 4 bolts in the order shown in the illustration.


Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Attach the grommet.


e.

Connect the connector.


Hide 68910 2.INSTALL POWER BACK DOOR UNIT SET ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 68960 3.INSTALL BACK DOOR STAY ASSEMBLY LH (w/o Power Back Door)

Hide 68950C 4.INSTALL BACK DOOR STAY ASSEMBLY RH (w/o Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 67837L 5.INSTALL DOOR DUST PROOF SEAL

a.
B408686

Attach the claw and install 3 new door dust proof seals.


Hide 67293A 6.INSTALL BACK DOOR STOPPER CUSHION

a.
B408685

Attach the claw to install a new back door stopper cushion.

HINT:

Use the same procedure as for the RH side.



Hide 67281F 7.INSTALL LOWER BACK DOOR STOPPER

a.
B408684

Attach the guide to install the lower back door stopper with the bolt.

HINT:

Use the same procedure as for the RH side.



Hide 85110R 8.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 69350 9.INSTALL BACK DOOR LOCK ASSEMBLY (w/ Easy Closer)

Hide 69350 10.INSTALL BACK DOOR LOCK ASSEMBLY (w/o Easy Closer)

Hide 89747E 11.INSTALL POWER BACK DOOR WARNING BUZZER (w/ Power Back Door)

Hide 89222A 12.INSTALL MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door)

Hide 89222A 13.INSTALL MULTIPLEX NETWORK DOOR ECU (w/ Easy Closer)

Hide 86790D 14.INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)

Hide 81690A 15.INSTALL LICENSE PLATE LIGHT ASSEMBLY LH

Hide 81270D 16.INSTALL LICENSE PLATE LIGHT ASSEMBLY RH

Hide 84840G 17.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY

Hide 76801 18.INSTALL BACK DOOR OUTSIDE GARNISH SUB-ASSEMBLY

Hide 81590A 19.INSTALL REAR LIGHT ASSEMBLY LH

Hide 81580A 20.INSTALL REAR LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 899A0A 21.INSTALL NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Entry and Start System)

Hide 67290 22.INSTALL BACK DOOR DAMPER ASSEMBLY

a.
B400248

Attach the guide.


b.

Install the back door damper assembly with the 3 bolts.


Hide 85345R 23.INSTALL REAR WASHER NOZZLE

Hide 24.INSTALL REAR SPOILER ASSEMBLY

Hide 64886B 25.INSTALL BACK DOOR GLASS CHANNEL LH

Hide 64885C 26.INSTALL BACK DOOR GLASS CHANNEL RH

HINT:

Use the same procedure as for the LH side.


Hide 84280D 27.INSTALL POWER BACK DOOR SENSOR ASSEMBLY LH (w/ Power Back Door)

Hide 84270G 28.INSTALL POWER BACK DOOR SENSOR ASSEMBLY RH (w/ Power Back Door)

HINT:

Use the same procedure as for the LH side.


Hide 67847A 29.INSTALL BACK DOOR SERVICE HOLE COVER (w/ Cover)

a.

Apply new butyl tape to the back door panel.


b.
B426616C01
0.563,0.49 0.563,0.219 0.563,0.219 0.771,0.219 true 2.865,0.51 2.865,0.24 2.865,0.24 2.719,0.24 true 0.729,0.135 0.958,0.354 0.229,0.219 10 true *a 2.542,0.125 2.771,0.344 0.229,0.219 10 true *a
*a Reference Point
V100143

Butyl Tape


Install a new back door service hole cover, and then attach the back door service hole cover using the reference points on the back door panel.

HINT:
·

Securely install the back door service hole cover to prevent wrinkles and air bubbles.

·

There should be no wrinkles or folds after installing the back door service hole cover.

·

After installing the back door service hole cover, check the seal quality.




Hide 67750 30.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

a.
B408683

Attach the clip to install the back door trim board assembly.


Hide 84931C 31.INSTALL BACK DOOR CONTROL SWITCH (w/ Power Back Door)

Hide 55539 32.INSTALL SPARE SWITCH HOLE COVER (w/o Power Back Door)

a.
B408696

Attach the claw to install the spare switch hole cover.


Hide 74811D 33.INSTALL DOOR PULL HANDLE

a.

w/ Power Back Door:

Connect the connector.


b.
B408682

Attach the claw to install the door pull handle.


Hide 67938A 34.INSTALL BACK DOOR SIDE GARNISH LH

a.
B408898

Attach the claw and clip to install the back door side garnish LH.


Hide 67937B 35.INSTALL BACK DOOR SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 67939B 36.INSTALL CENTER BACK DOOR GARNISH

a.
B408680

Attach the claw and clip to install the center back door garnish.


Hide 85143R 37.INSTALL REAR WIPER MOTOR GROMMET

Hide 38.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

Hide 85292A 39.INSTALL REAR WIPER ARM HEAD CAP

Hide 40.INSPECT POWER BACK DOOR SYSTEM (w/ Power Back Door)

Hide 41.INSPECT BACK DOOR CLOSER SYSTEM (w/ Easy Closer)