The illuminated entry system controls the engine switch illumination.
Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.
Connect the GTS to the DLC3.
Turn the engine switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Power/Engine SW Light | Engine switch illumination | OFF or ON | w/ Smart Entry and Start System |
| Tester Display |
|---|
| Power/Engine SW Light |
Engine switch illumination comes on.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the engine switch (engine switch illumination).
1GR-FE (for LHD)
Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
1GR-FE (for RHD)
Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
1KD-FTV (for LHD)
Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for LHD)>REMOVAL
1KD-FTV (for RHD)
Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for RHD)>REMOVAL
1GD-FTV
Click hereEngine / Hybrid System>1GD-FTV STARTING>ENGINE SWITCH>REMOVAL
2GD-FTV
Click hereEngine / Hybrid System>2GD-FTV STARTING>ENGINE SWITCH>REMOVAL
2TR-FE (for LHD)
Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
2TR-FE (for RHD)
Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
Inspect the engine switch (engine switch illumination).
1GR-FE (for LHD)
Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH(for LHD)>INSTALLATION
1GR-FE (for RHD)
Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH(for RHD)>INSTALLATION
1KD-FTV (for LHD)
Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for LHD)>INSTALLATION
1KD-FTV (for RHD)
Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for RHD)>INSTALLATION
1GD-FTV
Click hereEngine / Hybrid System>1GD-FTV STARTING>ENGINE SWITCH>INSTALLATION
2GD-FTV
Click hereEngine / Hybrid System>2GD-FTV STARTING>ENGINE SWITCH>INSTALLATION
2TR-FE (for LHD)
Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for LHD)>INSTALLATION
2TR-FE (for RHD)
Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for RHD)>INSTALLATION
Engine switch illumination is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
1GR-FE (for LHD)
Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
1GR-FE (for RHD)
Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
1KD-FTV (for LHD)
Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for LHD)>REMOVAL
1KD-FTV (for RHD)
Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for RHD)>REMOVAL
1GD-FTV
Click hereEngine / Hybrid System>1GD-FTV STARTING>ENGINE SWITCH>REMOVAL
2GD-FTV
Click hereEngine / Hybrid System>2GD-FTV STARTING>ENGINE SWITCH>REMOVAL
2TR-FE (for LHD)
Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
2TR-FE (for RHD)
Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
Disconnect the G45 engine switch (engine switch illumination) connector.
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G45-9 (SWIL) - G16-19 (SWIL) | Always | Below 1 Ω |
| G45-6 (AGND) - G16-24 (AGND) | Always | Below 1 Ω |
| G45-9 (SWIL) or G16-19 (SWIL) - Body ground | Always | 10 kΩ or higher |
| G45-6 (AGND) or G16-24 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG