Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING › from 2016.01
RM3270E _59 Vehicle Exterior _041722 EXTERIOR PANELS / TRIM _0205119 REAR DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the rear door belt moulding removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal
w/ Power Back Door System:

Reset back door close position


Power back door system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below are for RHD vehicles.

·

Fully open the rear door glass sub-assembly LH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67674A 3.REMOVE REAR DOOR FRAME GARNISH LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 74260 4.REMOVE REAR ARMREST ASSEMBLY LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 81230 6.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 69284D 7.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 67604 8.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 67842E 9.REMOVE REAR DOOR SERVICE HOLE COVER LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68152C 10.REMOVE REAR DOOR GLASS RUN LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 67408E 11.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68104 12.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 68124C 13.REMOVE REAR DOOR QUARTER WINDOW GLASS LH

HINT:

Use the same procedure described for the RH side.

Click hereVehicle Exterior>DOOR / HATCH>REAR DOOR>DISASSEMBLY


Hide 75724 14.REMOVE REAR DOOR REAR BELT MOULDING LH

a.
B409528C01
2.323,3.99 2.188,3.938 false
V113147

Remove in this Direction


Detach the clip and remove the rear door rear belt moulding LH as shown in the illustration.


Hide 75740 15.REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

a.
B409551C01
0.531,1.375 0.667,1.365 false
V100155

Protective Tape


Put protective tape around the rear door belt moulding assembly LH.


b.
B409530C01
1.677,0.5 1.688,0.708 false
V113147

Remove in this Direction


Using moulding remover D, detach the claw and remove the rear door belt moulding assembly LH as shown in the illustration.