The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the No. 1 black out tape removal/installation are shown below.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below are for RHD vehicles.
Fully open the front door glass sub-assembly LH before proceeding with work.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67492A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
74220
4.REMOVE FRONT ARMREST ASSEMBLY LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
6.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
81230
7.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)
69284C
8.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
67602
9.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
87940
10.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
67832
11.REMOVE FRONT DOOR SERVICE HOLE COVER LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
68151C
12.REMOVE FRONT DOOR GLASS RUN LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
68102
13.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Use the same procedure described for the RH side.
Click hereVehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY
75720
14.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY LH
67862
15.REMOVE FRONT DOOR WEATHERSTRIP LH
Using a clip remover, detach the clip and remove enough of the upper portion of the front door weatherstrip LH so that the No. 1 black out tape LH can be removed.
75922M
16.REMOVE NO. 1 BLACK OUT TAPE LH
When removing the No. 1 black out tape LH, heat the front door panel and No. 1 black out tape LH using a heat light.
| Item | Temperature |
|---|---|
| Front Door Panel | 40 to 60°C (104 to 140°F) |
| No. 1 Black Out Tape LH | 20 to 30°C (68 to 86°F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts.
Touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Pull back an edge of the No. 1 black out tape LH and pull it parallel to the front door panel to remove it.