Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › from 2016.01
RM3270E _59 Vehicle Exterior _041717 DOOR / HATCH _0205101 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front door disassembly/reassembly are shown below.

Necessary Procedures After Parts Removed / Installed / Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not Performed Link
Disconnect cable from negative battery terminal
w/ Power Back Door System:

Reset back door close position


Power back door system (Click here)

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below are for RHD vehicles.

·

Fully open the front door glass sub-assembly RH before proceeding with work.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67491A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH RH

a.

Detach the clip and claw and remove the front door lower frame bracket garnish RH.

B441622C01
0.031,0.063 0.281,0.26 0.25,0.198 10 true *A 3.635,0.073 3.885,0.271 0.25,0.198 10 true *B
*A w/ Front No. 2 Speaker *B w/o Front No. 2 Speaker



Hide 74210 4.REMOVE FRONT ARMREST ASSEMBLY RH

a.
B408804C01
0,0 0,0 false
V113146

Place Hands Here
V100135

Order of Removal
V113147

Remove in this Direction


Detach the clip and claw and remove the front armrest assembly RH as shown in the illustration.


Hide 5.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

a.
B408805C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and claw.


b.

Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.


Hide 84870A 6.REMOVE OUTER MIRROR SWITCH ASSEMBLY (for Driver Side)

Hide 84820 7.REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Driver Side)

Hide 8.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

a.
B408801C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the clip and claw.


b.

Disconnect the connector and remove the power window regulator switch assembly with front door armrest base panel.


Hide 84810 9.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 81230 10.REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

Hide 67665C 11.REMOVE FRONT DOOR TRIM REFLECTOR RH (w/ Reflex Reflector Assembly)

a.
B405481C01
0.094,0.115 0.406,0.313 0.313,0.198 10 true *A 0.094,2.313 0.406,2.51 0.313,0.198 10 true *B
*A for RH side
*B for LH side
V100155

Protective Tape
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Put protective tape around the reflex reflector.


b.

Using a thin-bladed screwdriver, detach the claw and guide.

HINT:

Tape the thin-bladed screwdriver tip before use.



c.

Remove the front door trim reflector RH.


Hide 69283 12.REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG RH

a.
B408806

Using moulding remover A, detach the claw and remove the front door inside handle bezel plug RH as shown in the illustration.


Hide 67601 13.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY RH

a.
B408807

Remove the 3 screws.


b.
B408808C01
0,0 0,0 false
V113146

Place Hands Here
V100135

Order of Removal (1)
V100136

Order of Removal (2)
V113147

Remove in this Direction


Detach the clip as shown in the illustration.


c.
B408811C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the guide and remove the front door trim board sub-assembly RH as shown in the illustration.


d.
B408810C01
0.833,0.844 0.833,0.417 0.833,0.417 1.146,0.417 true 0.844,1.344 0.844,1.76 0.844,1.76 1.302,1.76 true 1.208,0.333 1.417,0.552 0.208,0.219 10 true *1 1.333,1.667 1.542,1.885 0.208,0.219 10 true *2
*1 Front Door Inside Looking Cable Assembly RH
*2 Front Door Lock Remote Control Cable Assembly RH
V113147

Remove in this Direction


Detach the clamp and disconnect the front door lock remote control cable assembly RH and front door inside looking cable assembly RH as shown in the illustration.


Hide 69205 14.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY RH

a.
B408809C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and guide and remove the front door inside handle sub-assembly RH from the front door trim board sub-assembly RH.


Hide 68171B 15.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP RH

a.
B408812

Raise the claw of the front door inner glass weatherstrip RH as shown in the illustration, and then remove the front door inner glass weatherstrip RH from the front door trim board sub-assembly RH.


Hide 86160 16.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 86160P 17.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (w/ Front No. 2 Speaker)

Hide 89865 18.REMOVE DOOR SIDE AIR BAG SENSOR RH

Hide 87910 19.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


Hide 67831 20.REMOVE FRONT DOOR SERVICE HOLE COVER RH

a.
B408813C01
0,0 0,0 false
V100143

Butyl Tape


Remove the ground bolt and disconnect the ground wire.


b.

Detach the clamp.


c.

Pull out the front door lock remote control cable assembly RH, front door inside locking cable assembly RH and wire harness from the front door service hole cover RH, and then remove the front door service hole cover RH.

NOTICE:

Remove any remaining butyl tape from the front door panel.



Hide 21.REMOVE SCREW GROMMET

a.
B406725

Using a clip remover, detach the claw and remove the 2 screw grommets.


Hide 68141C 22.REMOVE FRONT DOOR GLASS RUN RH

a.
B408816

Detach the guide and remove the front door glass run RH.


Hide 68101 23.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY RH

a.

Temporarily install the power window regulator master switch assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Move the front door window regulator sub-assembly RH so that the front door glass sub-assembly RH bolts can be seen.


d.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



e.

Remove the power window regulator master switch assembly.


f.
B408814

Remove the 2 bolts.

NOTICE:

Be careful when removing the bolts as the glass may fall and become damaged.



g.
B408815C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the front door glass sub-assembly RH as shown in the illustration.

NOTICE:

Be careful not to damage the glass.



Hide 67403F 24.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY RH

a.
B408817

Remove the bolt.


b.

Detach the guide and remove the front door rear lower frame sub-assembly RH.


Hide 69801 25.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY RH

a.

Disconnect the connector.


b.

Loosen the temporarily bolt.

NOTICE:

Do not remove the temporarily bolt. If the temporarily bolt is removed, the front door window regulator sub-assembly RH may fall and become damaged.



c.
B408818C01
0,0 0,0 false
V100135

Bolt
V100136

Connector
V100137

Temporarily Bolt


Remove the 5 bolts and front door window regulator sub-assembly RH.


d.

Remove the temporarily bolt from the front door window regulator sub-assembly RH.


Hide 85710D 26.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

Hide 27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B408819C01
0.667,1.885 1.25,1.885 true 1.167,1.802 1.427,2.01 0.26,0.208 10 true *1
*1 Hole Plug
V113147

Remove in this Direction


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.


Hide 69217D 28.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

a.
B404251C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Using a thin-bladed screwdriver, detach the claw and guide and remove the front door outside handle cover from the lock cylinder assembly as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.



Hide 69217D 29.REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)

a.
B408821C01
2.656,1.969 3.208,1.969 true 2.49,1.875 2.729,2.083 0.24,0.208 10 true *1
*1 Hole Plug
V113147

Remove in this Direction


Remove the hole plug.


b.

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Detach the claw and remove the front door outside handle cover as shown in the illustration.


Hide 69310 30.REMOVE FRONT DOOR LOCK ASSEMBLY RH

Hide 69035A 31.REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY RH (w/o Double Locking System)

Hide 69750C 32.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY RH

Hide 69710B 33.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY RH

Hide 69318C 34.REMOVE DOOR LOCK WIRING HARNESS SEAL

Hide 69210 35.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY RH

a.

w/ Smart Entry and Start System:

i.
B408823C01
0,0 0,0 false
V100155

Protective Tape
V113147

Remove in this Direction


Using a thin-bladed screwdriver, detach the claw and open the connector cover as shown in the illustration.

HINT:

Tape the thin-bladed screwdriver tip before use.



ii.
B408820C01
0,0 0,0 false
V100155

Protective Tape


Using a thin-bladed screwdriver, detach the claw and disconnect the connector and connector cover.

HINT:

Tape the thin-bladed screwdriver tip before use.




b.
B408822C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the front door outside handle assembly RH as shown in the illustration.


Hide 69241H 36.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD

a.
B408824C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front door front outside handle pad.


Hide 69242E 37.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD

a.
B408825C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the claw and remove the front door rear outside handle pad.


Hide 69201A 38.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY RH

a.
B408826C01
1.26,0.771 1.052,0.469 1.052,0.469 0.771,0.469 true 2.26,0.469 2.438,0.167 2.438,0.167 2.698,0.167 true 2.271,0.781 2.521,1.073 2.521,1.073 2.75,1.073 true 0.583,0.344 0.823,0.583 0.24,0.24 10 true *a 2.625,0.073 2.854,0.292 0.229,0.219 10 true *b 2.656,0.969 2.885,1.188 0.229,0.219 10 true *b
*a Grommet
*b Guide
V113147

Remove in this Direction


Using a T30 "TORX" socket wrench, loosen the screw.


b.

Detach the grommet and guide and remove the front door outside handle frame sub-assembly RH together with the wire harness.


c.

w/ Smart Entry and Start System:

i.
B404265C01
1.323,1.594 1.167,1.594 1.167,1.594 1.167,1.208 false 1.667,1.427 1.927,1.427 1.927,1.427 1.927,1.042 false 2.344,0.885 2.708,0.885 true 1.344,1.49 1.656,1.688 0.313,0.198 10 false *a 2.729,0.781 3.042,0.979 0.313,0.198 10 false *a 1.469,1.313 1.781,1.51 0.313,0.198 10 false *b
*a Clamp
*b Guide


Detach the clamp and guide, disconnect the wire harness and remove the front door outside handle frame sub-assembly RH.



Hide 69311A 39.REMOVE FRONT DOOR LOCK OPEN ROD RH

a.
B404266C01
0,0 0,0 false
V113147

Remove in this Direction


Detach the snap and remove the front door lock open rod RH from the front door outside handle frame sub-assembly RH as shown in the illustration.


Hide 75710 40.REMOVE FRONT DOOR BELT MOULDING ASSEMBLY RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT DOOR BELT MOULDING>REMOVAL


Hide 67837B 41.REMOVE FRONT DOOR DUST PROOF SEAL

a.
B408853

Detach the claw and remove the 3 front door dust proof seals.


Hide 67001A 42.REMOVE FRONT DOOR PANEL CUSHION

a.
B408827

Detach the claw and remove the 2 front door panel cushions.


Hide 68610B 43.REMOVE FRONT DOOR CHECK ASSEMBLY RH

a.
B408829C01
0,0 0,0 false
V100135

Bolt (A)
V100136

Bolt (B)


Remove the 2 bolts (A), bolt (B) and front door check assembly RH.


Hide 67861 44.REMOVE FRONT DOOR WEATHERSTRIP RH

a.
B408828

Using a clip remover, detach the clip and remove the front door weatherstrip RH.


Hide 75921C 45.REMOVE NO. 1 BLACK OUT TAPE RH

HINT:

The procedure described below is for the LH side.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>BLACK OUT TAPE(for Front Door)>REMOVAL