Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2016.01
RM3270E _58 Vehicle Interior _041713 HEATING / AIR CONDITIONING _0205064 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  PTC Heater Circuit  


DESCRIPTION

The air conditioning amplifier assembly sends operation signals to the PTC heater relays when quick heater assembly operation conditions are met. Based on the signals from the air conditioning amplifier assembly, the PTC heater relays turn on, and power is supplied to the quick heater assembly installed in the air conditioning radiator assembly.

Quick Heater Assembly Operation Condition
Control ECU Condition
Air Conditioning Amplifier Assembly Start the engine
ECO mode switch: Off
Blower switch: LO or more
Temperature settings: MAX HOT
Light control switch: Off
·

Engine coolant temperature 65°C (149°F), or lower (3 PTC heater relays operating)

·

Engine coolant temperature 70°C (158°F), or lower (2 PTC heater relays operating)

·

Engine coolant temperature 75°C (167°F), or lower (A PTC heater relay operating)


Ambient temperature 10°C (50°F) or lower

WIRING DIAGRAM

E312543E19
5.375,4.781 6.927,5.177 1.552,0.396 10 false Air Conditioning Amplifier Assembly 5.354,4.625 5.813,4.823 0.458,0.198 10 false G37 5.302,1.208 5.552,1.385 0.25,0.177 10 false 40 5.313,2.49 5.625,2.656 0.313,0.167 10 false 39 5.396,3.771 5.708,3.938 0.313,0.167 10 false 3 5.615,1.208 6.115,1.385 0.5,0.177 10 false PTC2 5.615,2.49 6.115,2.667 0.5,0.177 10 false PTC1 5.615,3.771 6.115,3.948 0.5,0.177 10 false PTC3 3.26,2.042 4.677,2.208 1.417,0.167 10 false PTC HTR NO.2 3.448,3.302 4.865,3.469 1.417,0.167 10 false PTC NO.1 3.281,4.594 4.698,4.76 1.417,0.167 10 false PTC HTR NO.3 3.26,5.167 3.667,5.333 0.406,0.167 10 false G132 3.385,4.948 3.698,5.115 0.313,0.167 10 false 2 3.271,5.573 3.688,5.75 0.417,0.177 10 false G133 3.396,5.365 3.708,5.531 0.313,0.167 10 false 3 3.271,5.969 3.708,6.156 0.438,0.188 10 false G133 3.406,5.771 3.719,5.938 0.313,0.167 10 false 1 1.917,5.167 2.354,5.323 0.438,0.156 10 false G132 2.042,4.948 2.354,5.115 0.313,0.167 10 false 1 1.917,5.969 2.385,6.156 0.469,0.188 10 false G133 2.042,5.76 2.354,5.927 0.313,0.167 10 false 2 2,6.26 3.813,6.427 1.813,0.167 10 false Quick Heater Assembly 2.063,4.427 3.021,4.781 0.958,0.354 10 false CDS FAN/PTC HTR NO.3 2.063,3.146 3.167,3.354 1.104,0.208 10 false PTC HTR NO.1 2.031,1.875 3.125,2.073 1.094,0.198 10 false PTC HTR NO.2 4.26,4.156 4.573,4.323 0.313,0.167 10 false 3 3.104,4.156 3.417,4.323 0.313,0.167 10 false 5 4.26,3.76 4.573,3.927 0.313,0.167 10 false 1 3.104,3.76 3.417,3.927 0.313,0.167 10 false 2 4.25,2.875 4.563,3.042 0.313,0.167 10 false 3 3.104,2.854 3.417,3.021 0.313,0.167 10 false 5 4.25,2.469 4.563,2.635 0.313,0.167 10 false 2 3.104,2.469 3.417,2.635 0.313,0.167 10 false 1 4.26,1.604 4.573,1.771 0.313,0.167 10 false 3 4.25,1.208 4.563,1.375 0.313,0.167 10 false 2 3.104,1.615 3.417,1.781 0.313,0.167 10 false 5 3.104,1.208 3.417,1.375 0.313,0.167 10 false 1 1.927,0.635 3.24,0.833 1.313,0.198 10 false from Battery 0.938,0.302 1.844,0.448 0.906,0.146 10 false IG1 NO.4 1.896,0.135 4.802,0.354 2.906,0.219 10 false from Ignition Switch*1, IG1 NO.1 Relay*2 3.083,5.083 3.396,5.25 0.313,0.167 10 false B 3.083,5.49 3.396,5.656 0.313,0.167 10 false B 3.083,5.885 3.396,6.052 0.313,0.167 10 false B 2.333,5.083 2.646,5.25 0.313,0.167 10 false E 2.323,5.885 2.635,6.052 0.313,0.167 10 false E 0.083,6.531 2.99,6.75 2.906,0.219 10 false *1: w/o Smart Entry and Start System 2.542,6.521 5.448,6.74 2.906,0.219 10 false *2: w/ Smart Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When the battery is disconnected or the air conditioning amplifier assembly is replaced, be sure to perform servo motor initialization.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>INITIALIZATION



PROCEDURE

1.INSPECT PTC HEATER RELAY (PTC NO.1, PTC HTR NO.2, PTC HTR NO.3)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)

NG

REPLACE PTC HEATER RELAY (PTC NO.1, PTC HTR NO.2, PTC HTR NO.3)

2.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
PTC NO.1:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.2:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V
Relay terminal 1 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V

PTC HTR NO.3:
Tester Connection Condition Specified Condition
Relay terminal 5 - Body ground Always 11 to 14 V
Relay terminal 2 - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.


b.

Disconnect the G37 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC NO.1:
Tester Connection Condition Specified Condition
Relay terminal 2 - G37-39 (PTC1) Always Below 1 Ω
Relay terminal 2 or G37-39 (PTC1)- Body ground Always 10 kΩ or higher

PTC HTR NO.2:
Tester Connection Condition Specified Condition
Relay terminal 2 - G37-40 (PTC2) Always Below 1 Ω
Relay terminal 2 or G37-40 (PTC2) - Body ground Always 10 kΩ or higher

PTC HTR NO.3:
Tester Connection Condition Specified Condition
Relay terminal 1 - G37-3 (PTC3) Always Below 1 Ω
Relay terminal 1 or G37-3 (PTC3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - PTC HEATER RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (QUICK HEATER ASSEMBLY - PTC HEATER RELAY AND BODY GROUND)
a.

Remove the PTC heater relays from the No. 5 instrument panel relay block.


b.

Disconnect the G132 and G133 quick heater assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
PTC NO.1:
Tester Connection Condition Specified Condition
G133-3 (B) - Relay terminal 3 Always Below 1 Ω
G132-1 (E) - Body ground Always Below 1 Ω
G133-2 (E) - Body ground Always Below 1 Ω
G133-3 (B) or relay terminal 3 - Body ground Always 10 kΩ or higher

PTC HTR NO.2:
Tester Connection Condition Specified Condition
G133-1 (B) - Relay terminal 3 Always Below 1 Ω
G133-2 (E) - Body ground Always Below 1 Ω
G133-1 (B) or relay terminal 3 - Body ground Always 10 kΩ or higher

PTC HTR NO.3:
Tester Connection Condition Specified Condition
G132-2 (B) - Relay terminal 3 Always Below 1 Ω
G132-1 (E) - Body ground Always Below 1 Ω
G132-2 (B) or relay terminal 3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT QUICK HEATER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT QUICK HEATER ASSEMBLY
a.

b.

Result:
Proceed to
OK
NG



OK

NG