Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat) › from 2016.08
RM3270E _58 Vehicle Interior _041711 SEAT _0203008 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:
·
B394717

Wear protective gloves. Sharp areas on the parts may injure your hands.

·

There is risk of injury.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for RHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 71051A 1.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY RH

a.
B452653C05
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


While rotating the part in installation direction (1) shown in the illustration, attach the hook.


b.

Push in installation direction (2) shown in the illustration to attach the hook and install the front seat cushion spring sub-assembly RH.


Hide 82191 2.INSTALL FRONT SEAT WIRE RH

a.
B403888C01
0.698,2.865 0.917,2.458 true 2.229,2.958 1.792,2.573 true 2.615,2.542 2.208,2.198 true 1,1.948 0.479,1.573 true 0.208,1.365 0.406,1.542 0.198,0.177 10 true *2 0.594,2.938 0.792,3.115 0.198,0.177 10 true *1 2.229,3 2.427,3.177 0.198,0.177 10 true *1 2.688,2.552 2.885,2.729 0.198,0.177 10 true *1
*1 Wire Harness Clamp
*2 Connector Clamp


Connect the 3 connectors.


b.

Attach the wire harness clamp and connector clamp.


Hide 71537G 3.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

a.
B403885C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in the installation direction (1) shown in the illustration to attach the guide.


b.

While expanding the part in the installation direction (2) shown in the illustration, attach the claw.


c.

Install the front seat cushion edge protector RH with the screw.


Hide 71538B 4.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

HINT:

Use the same procedure as for the RH side.


Hide 71873 5.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

a.
B411101C04
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push in the installation direction (1) shown in the illustration to temporarily install the front seat lower cushion shield RH.


b.

Push in the installation direction (2) shown in the illustration to attach the clip.


c.
B411102C04
0,0 0,0 false
V113147

Install in this Direction


Push in the guide in the installation direction shown in the illustration.


d.

Install the front seat lower cushion shield RH with the screw.


Hide 71874 6.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

HINT:

Use the same procedure as for the RH side.


Hide 7.INSTALL SEAT COVER WIRE

a.
B442727N05
1.708,0.656 1.26,0.396 true 2.167,0.406 1.708,0.646 true 2.948,0.625 2.615,0.823 true 3.063,2 2.729,2.198 true 0.823,0.844 0.573,0.677 true 0.719,2.188 0.469,2.021 true 1.719,1.292 1.719,1.625 true 1.719,2.26 1.719,2.594 true 1.667,0.708 1.823,0.906 0.156,0.198 10 true A 2.99,0.51 3.146,0.708 0.156,0.198 10 true B 0.375,0.51 0.531,0.708 0.156,0.198 10 true B 1.677,1.646 1.833,1.844 0.156,0.198 10 true C 1.677,2.615 1.833,2.813 0.156,0.198 10 true D 0.271,1.833 0.427,2.031 0.156,0.198 10 true E 3.104,1.854 3.26,2.052 0.156,0.198 10 true E

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm (3.28 ft.) or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm (3.28 ft.) supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 170 mm (6.70 in.)
B 150 mm (5.91 in.)
C 230 mm (9.06 in.)
D 270 mm (10.63 in.)
E 290 mm (11.42 in.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 71071S 8.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seat cushion cover when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394024N24
2.5,0.24 3.271,0.438 0.771,0.198 10 false A - A 4.656,0.302 5.427,0.5 0.771,0.198 10 false B - B 0.198,0.396 0.354,0.594 0.156,0.198 10 false A 0.51,0.583 0.656,0.75 0.146,0.167 10 true A 0.938,0.802 1.094,1 0.156,0.198 10 false B 1.26,1.063 1.656,1.406 0.396,0.344 10 false B



a.

Temporarily install the separate type front seat cushion cover to the separate type front seat cushion pad.


b.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 18 new hog rings in the order shown in the illustration.

B409602C01
5.25,2.177 5.323,1.667 false 4.969,0.927 5.115,0.938 true 5.115,0.844 5.427,1.042 0.313,0.198 10 false *a 5.167,2.229 5.479,2.427 0.313,0.198 10 false *1 1.99,1.771 2.208,1.979 0.219,0.208 10 true (1) 2.615,1.781 2.833,1.99 0.219,0.208 10 true (2) 1.979,1.156 2.198,1.365 0.219,0.208 10 true (3) 2.594,1.156 2.813,1.365 0.219,0.208 10 true (4) 1.365,1.844 1.635,2.052 0.271,0.208 10 true (10) 1.417,1.354 1.688,1.563 0.271,0.208 10 true (11) 1.448,1.104 1.729,1.313 0.281,0.208 10 true (12) 1.448,0.792 1.729,1 0.281,0.208 10 true (13) 1.49,0.51 1.75,0.719 0.26,0.208 10 true (14) 3.146,1.844 3.365,2.052 0.219,0.208 10 true (5) 3.135,1.365 3.354,1.573 0.219,0.208 10 true (6) 3.135,1.125 3.354,1.333 0.219,0.208 10 true (7) 3.125,0.833 3.344,1.042 0.219,0.208 10 true (8) 3.104,0.563 3.323,0.771 0.219,0.208 10 true (9) 1.802,0.177 2.073,0.385 0.271,0.208 10 true (18) 2.125,0.177 2.385,0.385 0.26,0.208 10 true (17) 2.427,0.177 2.688,0.385 0.26,0.208 10 true (16) 2.75,0.177 3.021,0.417 0.271,0.24 10 true (15)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seat cushion cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.



HINT:

Install the hog rings at the cutouts if they are there.



c.

Using hog ring pliers, connect the 2 straps of the separate type front seat cushion cover to the separate type front seat cushion pad with 2 new hog rings.

B409603C01
4.844,1.969 5.135,1.563 false 4.729,2.031 5.042,2.229 0.313,0.198 10 false *1
*1 Hog Ring Pliers - -


NOTICE:
·

Do not dirty or damage the separate type front seat cushion cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.




Hide 9.INSTALL SEAT CUSHION COVER WITH PAD

a.

While sliding the part in the direction indicated by the arrow shown in the illustration, align the J hook to attach the seat cushion cover with pad.

B402132


Hide 71587B 10.INSTALL FRONT SEATBACK EDGE PROTECTOR

a.
B409604

Attach the claw to install the 2 front seatback edge protectors.


Hide 71053S 11.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY RH

a.
B456615C04
0.521,1.229 1.385,1.469 true 1.958,1.375 2.74,0.635 true 0.292,1.083 0.604,1.24 0.313,0.156 10 false *1 2.771,0.448 3.083,0.604 0.313,0.156 10 false *1
*1 Front No. 2 Seatback Hook
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Temporarily install the 2 front No. 2 seatback hooks to the front seatback spring sub-assembly RH.


b.

Push in installation direction (1) shown in the illustration to install the front seatback spring sub-assembly RH.


c.

Push in installation direction (2) shown in the illustration to temporarily the front seatback spring sub-assembly RH.


d.
B403873

Attach the claw and install the 2 front seatback edge protectors.


Hide 71759D 12.INSTALL FRONT NO. 2 SEATBACK HOOK

a.
B403872C01
0,0 0,0 false
V113147

Install in this Direction


Push up installation direction shown in the illustration to attach the claw and install the 2 front No. 2 seatback hooks.


Hide 71759B 13.INSTALL FRONT SEATBACK HOOK

a.
B418329

Attach the claw and hook to install the 2 front seatback hooks.


Hide 73910A 14.INSTALL FRONT SEAT AIRBAG ASSEMBLY RH (w/ Front Seat Side Airbag)

Hide 8219A 15.INSTALL FRONT SEAT NO. 2 WIRE RH

a.
B403893

Connect the connector.


b.

Attach the wire harness clamp and install the front seat No. 2 wire RH.


Hide 16.INSTALL SEAT COVER WIRE

a.
B413333N01
1.969,1.365 2.917,1.115 true 2.333,2.969 2.885,3.021 true 2.313,3.198 2.896,3.021 true 2.99,1.021 3.146,1.219 0.156,0.198 10 true A 2.958,2.938 3.115,3.135 0.156,0.198 10 true B

Install the seat cover wire.

HINT:
·

There are service parts available for wires of 1000 mm (3.28 ft.) or longer and formed wires.


·

When a wire that is less than 1000 mm (3.28 ft.) in length is needed, cut and shape a 1000 mm (3.28 ft.) supplied wire into the dimensions shown in the illustration.


·

Refer to the precautions when creating a wire.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION



Length:
A 290 mm (11.42 in.)
B 420 mm (1.38 ft.)


HINT:
B376752

The dimensions shown in the illustration are the length.



Hide 71073S 17.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

HINT:
·

Refer to the precautions on wrinkles to avoid creating any on the separate type front seatback cover when installing the seat cover.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>PRECAUTION


·

As shown in the illustration, fix all of the cover seam allowances in the same direction.

B394023N01
0.542,0.354 0.698,0.552 0.156,0.198 10 false A 0.813,0.458 0.969,0.656 0.156,0.198 10 false A 1.177,0.583 1.333,0.781 0.156,0.198 10 false B 1.5,0.719 1.656,0.917 0.156,0.198 10 true B 1.125,0.052 1.281,0.25 0.156,0.198 10 false C 0.813,0.24 0.969,0.438 0.156,0.198 10 true C 2.042,0.229 2.813,0.427 0.771,0.198 10 false A - A 3.438,0.24 4.208,0.438 0.771,0.198 10 false C - C 5.615,0.281 6.385,0.479 0.771,0.198 10 false B - B



a.

Set the separate type front seatback cover.


b.

Using hog ring pliers, install the separate type front seatback cover with 6 new hog rings in the order shown in the illustration.

B409606C01
5.25,2.229 5.24,1.646 true 5.094,0.948 4.958,0.938 true 3.417,0.427 3.063,0.719 true 1.74,0.302 2,0.563 true 1.563,0.802 1.979,1.188 true 1.563,0.792 2.271,1.156 true 2.75,1.219 3.365,1.146 true 2.927,1.375 3.365,1.156 true 5.115,0.854 5.427,1.052 0.313,0.198 10 false *a 5.198,2.281 5.51,2.479 0.313,0.198 10 false *1 3.417,0.229 3.875,0.427 0.458,0.198 10 false (1) 1.563,0.135 2.021,0.333 0.458,0.198 10 false (1) 1.365,0.677 1.823,0.875 0.458,0.198 10 false (2) 3.417,1.052 3.875,1.25 0.458,0.198 10 false (2)
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seat cushion cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 18.INSTALL SEATBACK COVER WITH PAD

a.
B415862C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to temporarily install the seatback cover with pad.


b.

w/ Front Seat Side Airbag:

i.
B408562C01
1.719,1.792 2.594,1.938 true 0.594,2.76 1.375,2.719 true 2.667,1.865 2.875,2.063 0.208,0.198 10 false *1 0.375,2.667 0.583,2.865 0.208,0.198 10 false *2
*1 J Hook A
*2 J Hook B
V113147

Install in this Direction


Push in installation direction shown in the illustration to attach the J hook A and J hook B.


ii.
B408563C01
0.833,0.563 1.24,1.281 true 2.073,2.885 2.417,3.094 true 0.656,0.438 0.969,0.635 0.313,0.198 10 false *2 2.479,3.052 2.792,3.25 0.313,0.198 10 false *1
*1 J Hook B (J Hook A and J Hook B)
*2 J Hook C
V113147

Install in this Direction


Push in installation direction shown in the illustration to attach the J hook B (J hook A and J hook B) and J hook C.


iii.

Install a new rivet to J hook B.

B413208C14
2.219,1.656 3.104,1.177 true 0.74,1.75 1.854,1.729 true 5.542,1.771 6.625,1.656 true 4.229,1.135 5.208,1.583 true 0.083,0.083 0.469,0.385 0.385,0.302 12 false *A 3.583,0.083 3.917,0.365 0.333,0.281 12 false *B 0.542,1.677 0.854,1.875 0.313,0.198 10 false *1 6.688,1.542 7,1.74 0.313,0.198 10 false *1 3.167,1.063 3.479,1.26 0.313,0.198 10 false *2 4.021,1.063 4.333,1.26 0.313,0.198 10 false *2
*A for LH seat *B for RH seat
*1 J Hook A *2 J Hook B



iv.

Place your hand at the position shown in the illustration and push in installation direction to attach the J hook B.

B408564C01
5.188,1.656 5.646,2.219 true 4.24,1.042 4.729,1.448 true 5.469,0.927 5.74,0.635 true 5.677,2.198 5.99,2.396 0.313,0.198 10 false *1 4.063,0.927 4.375,1.125 0.313,0.198 10 false *2 5.729,0.5 6.042,0.698 0.313,0.198 10 false *3
*1 J Hook A *2 J Hook B
*3 J Hook C - -
V113146

Place Hand Here
V113147

Install in this Direction




Hide 71931 19.INSTALL FRONT SEAT HEADREST SUPPORT

a.
B403861C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and install the 2 front seat headrest supports.


b.
B456654C12
0,0 0,0 false
V113147

Install in this Direction


Pull up in the installation direction shown in the illustration to attach the guide to the 2 straps.


c.
B413232C01
0,0 0,0 false
V113147

Install in this Direction


Close the fasteners as shown in the illustration.


d.
B403894C02
0.083,0.083 0.375,0.323 0.292,0.24 12 true *A 0.083,2.417 0.375,2.656 0.292,0.24 12 true *B
*A w/ Front Seat Side Airbag
*B w/o Front Seat Side Airbag
V113147

Install in this Direction


Pass the wire harness through the opening in the back cover.


e.

Using hog ring pliers, install 6 new hog rings.

B456659C06
5.063,2.229 5.219,1.729 false 4.885,1.115 5.448,0.802 true 4.969,2.24 5.281,2.396 0.313,0.156 10 false *1 5.49,0.646 5.802,0.802 0.313,0.156 10 false *a
*1 Hog Ring Pliers - -
*a Cutout - -


NOTICE:
·

Do not dirty or damage the separate type front seat cushion cover.


·

Securely tighten the hog rings as shown in the illustration while making sure wrinkles do not form in the center of the fabric and separate type front seat cushion pad.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 71759C 20.INSTALL FRONT NO. 1 SEATBACK HOOK

a.
B403851

Attach the claw and install the front No. 1 seatback hook.


Hide 71875E 21.INSTALL RECLINING ADJUSTER INSIDE COVER RH

a.
B456648C03
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Push down to attach the guide installation direction (1) shown in the illustration.


b.

Rotate the part in installation direction (2) shown in the illustration to install the reclining adjuster inside cover RH.


Hide 71875G 22.INSTALL RECLINING ADJUSTER INSIDE COVER LH

HINT:

Use the same procedure as for the RH side.


Hide 71013S 23.INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY RH

a.
B443637C06
0.083,0.083 0.396,0.24 0.313,0.156 12 false *A 0.083,2.25 0.396,2.406 0.313,0.156 12 false *B
*A RH Side
*B LH Side


Install the 4 bolts and front seatback frame sub-assembly RH.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B443638C06
1.354,4.26 2.573,3.969 true 0.479,0.594 1.729,1.177 true 2.583,3.875 2.896,4.073 0.313,0.198 10 false *1 0.271,0.5 0.469,0.698 0.198,0.198 10 false *1 0.083,0.083 0.396,0.281 0.313,0.198 12 false *A 0.083,2.167 0.396,2.365 0.313,0.198 12 false *B
*A RH Side
*B LH Side
*1 Separate Type Front Seat Cushion Cover


Attach the 2 hooks.


c.
B444909

Attach the guide.


d.

w/ Front Seat Side Airbag:

i.
B403877

Attach the wire harness clamp.


ii.
B403868C01
0.958,3.052 0.729,2.26 true 2.188,2.917 1.063,1.979 true 1.917,1.385 1.448,0.479 true 2.74,0.917 2.625,0.542 true 1.25,0.302 1.448,0.5 0.198,0.198 10 true *1 2.479,0.323 2.677,0.521 0.198,0.198 10 true *1 2.229,2.938 2.427,3.135 0.198,0.198 10 true *1 0.927,3.104 1.125,3.302 0.198,0.198 10 true *2
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the wire harness clamp and connector clamp.



e.
B403856

Install the band in the position shown in the illustration.


Hide 73230 24.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH

Hide 71861 25.INSTALL FRONT SEAT INNER CUSHION SHIELD RH

a.
B403849C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to attach the claw and guide.


b.
B409608C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the front seat inner cushion shield RH.


Hide 84922B 26.INSTALL FRONT POWER SEAT SWITCH RH

Hide 71811D 27.INSTALL FRONT SEAT CUSHION SHIELD RH

a.
B442770

Attach the 2 claws in the direction indicated by the arrow shown in the illustration.


b.
B442764C14
1.594,2.667 1.375,1.927 true 1.635,1.781 1.979,0.583 true 1.531,2.677 1.844,2.833 0.313,0.156 10 false *1 1.938,0.365 2.25,0.542 0.313,0.177 10 false *2
*1 Connector Clamp
*2 Guide


Attach the guide and connector clamp.


c.

Connect the connector.


d.
B442763

Connect the connector.


e.
B442762

Attach the wire harness clamp and connect the connector.


f.
B442761

Attach the clip.


g.
B442769C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the guide.


h.
B442768C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and guide.


i.
B442767C01
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and guide.


j.
B403828C02
0,0 0,0 false
V113147

Install in this Direction


Push in the installation direction shown in the illustration to attach the claw and install the front seat cushion shield RH.


Hide 71867A 28.INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH

a.
B403823C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to install the guide.


b.

Install the screw and front seat inner No. 1 cushion shield RH.


Hide 84921J 29.INSTALL POWER SEAT SWITCH KNOB RH (for Reclining)

a.
B403821C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the power seat switch knob RH.


Hide 84921C 30.INSTALL POWER SEAT SWITCH KNOB RH (for Slide and Vertical, Lifter)

a.
B403819C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration and attach the claw to install the power seat switch knob RH.


Hide 71848A 31.INSTALL SEAT ADJUSTER COVER CAP RH

a.
B403801C01
0,0 0,0 false
V113147

Install in this Direction


Push in installation direction shown in the illustration to install the 2 seat adjuster cover caps RH.


Hide 71910A 32.INSTALL FRONT SEAT HEADREST ASSEMBLY

a.
B435709C01
0,0 0,0 false
V100155

Application Area
V100136

Apply Silicon


Apply silicon lubricant to the application area.

HINT:

The application area shown in the illustration is 20 + / -10 mm.



b.

Install the front seat headrest assembly.