Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › IGNITION SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068461 IGNITION SYSTEM G

2TR-FE ENGINE CONTROL  IGNITION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.PERFORM IGNITION COIL AND SPARK TEST

a.

Check for DTCs (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

Powertrain > Engine > Trouble Codes
50001 61
NOTICE:

If a DTC is output, perform troubleshooting procedures for that DTC.



b.

Check if sparks occur.

i.

Remove the ignition coils and spark plugs (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL).


ii.

Install the spark plug to the ignition coil and connect the ignition coil connector.


iii.

Disconnect the 4 injector connectors.


iv.

Ground the spark plug.


v.

Visually check that sparks occur while the engine is being cranked.

NOTICE:
·

Be sure to ground the spark plug when checking.

·

If the ignition coil has been struck or dropped, replace it.

·

Do not crank the engine for more than 2 seconds.





c.

Spark test procedure.

i.

Check that the wire harness side connector of the ignition coil with igniter is securely connected.

Result:
Result Proceed to
NG Connect securely
OK Go to next step



ii.

Perform spark test on each ignition coil with igniter.

1. Replace the ignition coil with igniter with a normal one.

2. Perform a spark test again.

Result:
Result Proceed to
NG Replace ignition coil with igniter
OK Go to next step




iii.

Check the spark plug.

Result:
Result Proceed to
NG Replace spark plug
OK Go to next step



iv.

Check the power supply to the ignition coil with igniter.

1. Turn the ignition switch to ON.

2. Check that there is battery voltage at the ignition coil positive (+) terminal.

Result:
Result Procedure
NG Check wiring between ignition switch and ignition coil with igniter
OK Go to next step




v.

Check the camshaft position sensor (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>P0340).


vi.

Check the crankshaft position sensor (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>P0335).


vii.

Check the IGT signal circuit (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>P0351).



d.

Connect the 4 injector connectors.


e.

Install the 4 ignition coils and 4 spark plugs (See page Engine / Hybrid System>2TR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION).


Hide 2.INSPECT SPARK PLUG

NOTICE:
·

Do not use a wire brush for cleaning.

·

Do not attempt to adjust the electrode gap of a used spark plug.



a.
A120009
1.073,2.583 0.771,2.698 0.771,2.698 0.688,2.698 true 0.479,2.625 0.677,2.781 0.198,0.156 10 false *1
*1 Body Ground


Check the electrode.

i.

Using a megohmmeter, measure the insulation resistance.

Standard Insulation Resistance
Tester Connection Condition Specified Condition
Spark plug (terminal part) - Body ground Always 10 MΩ or higher

HINT:

If a megohmmeter is not available, perform the following simple inspection instead.




b.

Alternative inspection method:

i.

Quickly accelerate the engine to 4000 rpm 5 times.


ii.

Remove the spark plug.


iii.

Visually check the spark plug.

If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.



c.

Check the spark plug for any damage on its threads and insulator.

If there is damage, replace the spark plug. If not, reinstall the spark plug.

Recommended Spark Plug:
Manufacturer Product
DENSO K20HR-U11



d.

Check the spark plug electrode gap.

Standard electrode gap:

1.0 to 1.1 mm (0.0394 to 0.0433 in.)


Maximum electrode gap:

1.3 mm (0.0512 in.)


If the gap is more than the maximum, replace the spark plug.


e.
A301633

Clean the spark plugs.

If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner, and then dry it.

Air pressure:

588 kPa (6.0 kgf/cm2, 85 psi)


Duration:

20 seconds or less


HINT:

Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.