Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM C

2TR-FE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is stored, check the No. 1 ignition coil circuit.

·

If DTC P0352 is stored, check the No. 2 ignition coil circuit.

·

If DTC P0353 is stored, check the No. 3 ignition coil circuit.

·

If DTC P0354 is stored, check the No. 4 ignition coil circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A129406
5.365,1.156 5.802,0.865 false 4.313,0.896 4.396,0.896 4.396,0.896 4.49,1.396 true 0.292,1.438 1.99,1.615 1.698,0.177 10 false Crankshaft Position Sensor 0.313,3.208 2.073,3.385 1.76,0.177 10 false Camshaft Position Sensors 0.188,4.271 2.146,5.031 1.958,0.76 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 1.854,6.094 2.417,6.271 0.563,0.177 10 false to DLC3 2.719,5.677 3.115,5.854 0.396,0.177 10 false TACH 2.719,0.646 3.042,0.823 0.323,0.177 10 false ECM 2.865,1.469 3.188,1.646 0.323,0.177 10 false IGT1 2.865,1.771 3.188,1.948 0.323,0.177 10 false IGF1 2.865,2.771 3.188,2.948 0.323,0.177 10 false IGT2 2.865,4.104 3.188,4.281 0.323,0.177 10 false IGT3 2.865,5.417 3.188,5.594 0.323,0.177 10 false IGT4 4.542,0.49 5.365,0.667 0.823,0.177 10 false from Battery 3.906,0.792 4.313,0.969 0.406,0.177 10 false Igniter 5.854,0.781 7.031,0.969 1.177,0.188 10 false No. 1 Ignition Coil 5.615,1.875 6.74,2.115 1.125,0.24 10 false No. 1 Spark Plug 4.198,2.76 5.375,2.948 1.177,0.188 10 false No. 2 Ignition Coil 4.188,4.094 5.354,4.292 1.167,0.198 10 false No. 3 Ignition Coil 4.167,5.385 5.333,5.573 1.167,0.188 10 false No. 4 Ignition Coil 5.615,3.083 6.74,3.281 1.125,0.198 10 false No. 2 Spark Plug 5.604,4.396 6.729,4.583 1.125,0.188 10 false No. 3 Spark Plug 5.625,5.719 6.688,5.896 1.063,0.177 10 false No. 4 Spark Plug

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (ECM does not receive any IGF signals despite the ECM sending an IGT signal to the igniter) (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT (1 to 4) circuit between ignition coil and ECM

·

No. 1 to No. 4 ignition coil assemblies

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (ECM does not receive any IGF signals despite the ECM sending an IGT signal to the igniter) (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT (1 to 4) circuit between ignition coil and ECM

·

No. 1 to No. 4 ignition coil assemblies

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (ECM does not receive any IGF signals despite the ECM sending an IGT signal to the igniter) (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT (1 to 4) circuit between ignition coil and ECM

·

No. 1 to No. 4 ignition coil assemblies

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal is sent to the ECM while the engine is running (ECM does not receive any IGF signals despite the ECM sending an IGT signal to the igniter) (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT (1 to 4) circuit between ignition coil and ECM

·

No. 1 to No. 4 ignition coil assemblies

·

ECM


Comes on DTC stored

Reference: Inspection using an oscilloscope.

A301508
0.594,0.156 1.823,0.354 1.229,0.198 10 false 2 V/DIV. 0.927,0.719 1.219,0.927 0.292,0.208 10 false IGT 0.927,1.313 1.208,1.521 0.281,0.208 10 false IGF 0.646,0.917 1.031,1.167 0.385,0.25 10 false GND 0.656,1.521 1.042,1.771 0.385,0.25 10 false GND 1.813,1.875 2.781,2.094 0.969,0.219 10 false 20 msec./DIV.

Tester Connection Tool Setting Condition Specified Condition
C75-17 (IGT1) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C75-16 (IGT2) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C75-15 (IGT3) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C75-14 (IGT4) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown
C75-23 (IGF1) - C75-3 (E1) 2 V/DIV., 20 msec./DIV. Idling The correct waveform is as shown

HINT:

While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.



MONITOR DESCRIPTION

A212405
1.781,1.646 2.5,1.969 0.719,0.323 10 false ECM 2.958,1.302 3.375,1.615 0.417,0.313 10 false IGT 2.958,1.74 3.396,2.104 0.438,0.365 10 false IGF 4.156,1.51 4.719,1.865 0.563,0.354 10 false Igniter 5.406,1.375 6.24,1.667 0.833,0.292 10 false Ignition Coil 4.5,2.385 6.313,2.729 1.813,0.344 10 false Ignition Coil Assembly 0.208,3.115 1.125,3.635 0.917,0.521 10 false Ignition Signal (IGT) 1.646,3.542 2.396,3.896 0.75,0.354 10 false Normal 1.385,3.948 2.417,4.458 1.031,0.51 10 false Malfunction 0.26,3.906 1.073,4.823 0.813,0.917 10 false Ignition Confirmation Signal (IGF) 3.635,4.51 4.844,4.927 1.208,0.417 10 false Circuit Open 5.948,4.969 6.604,5.375 0.656,0.406 10 false Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 1 second after the engine is next started.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) ECM
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A247770
5.656,0.792 6.021,0.948 0.365,0.156 10 false IGT1 3.938,0.677 4.271,0.833 0.333,0.156 10 false IGT1 4.01,1.01 4.281,1.167 0.271,0.156 10 false IGF 3.615,0.677 3.844,0.833 0.229,0.156 10 false +B 3.604,1.01 3.958,1.167 0.354,0.156 10 false GND 5.656,2.188 6.021,2.385 0.365,0.198 10 false IGT2 5.656,3.573 6.021,3.729 0.365,0.156 10 false IGT3 5.656,4.979 6.021,5.135 0.365,0.156 10 false IGT4 5.656,5.75 6.021,5.906 0.365,0.156 10 false IGF1 6.156,6.198 6.448,6.375 0.292,0.177 10 false C75 6.156,6.354 6.531,6.521 0.375,0.167 10 false ECM 5.396,0.573 5.604,0.75 0.208,0.177 10 false 17 5.385,5.521 5.604,5.698 0.219,0.177 10 false 23 5.385,4.75 5.604,4.927 0.219,0.177 10 false 14 5.385,3.354 5.604,3.531 0.219,0.177 10 false 15 5.385,1.948 5.604,2.125 0.219,0.177 10 false 16 3.406,0.573 3.531,0.74 0.125,0.167 10 false 1 3.406,0.896 3.531,1.063 0.125,0.167 10 false 4 4.354,0.573 4.479,0.74 0.125,0.167 10 false 3 4.354,0.896 4.479,1.063 0.125,0.167 10 false 2 3.24,1.292 3.542,1.448 0.302,0.156 10 false C70 3.24,1.448 4.365,1.688 1.125,0.24 10 false No. 1 Ignition Coil 3.406,1.969 3.531,2.135 0.125,0.167 10 false 1 3.406,2.302 3.531,2.469 0.125,0.167 10 false 4 4.354,1.969 4.479,2.135 0.125,0.167 10 false 3 4.354,2.302 4.479,2.469 0.125,0.167 10 false 2 3.24,2.719 3.542,2.875 0.302,0.156 10 false C71 3.24,2.875 4.333,3.125 1.094,0.25 10 false No. 2 Ignition Coil 3.406,3.354 3.531,3.521 0.125,0.167 10 false 1 3.406,3.677 3.531,3.844 0.125,0.167 10 false 4 4.354,3.354 4.479,3.521 0.125,0.167 10 false 3 4.354,3.677 4.479,3.844 0.125,0.167 10 false 2 3.24,4.115 3.542,4.271 0.302,0.156 10 false C72 3.24,4.271 4.375,4.448 1.135,0.177 10 false No. 3 Ignition Coil 3.406,4.74 3.531,4.906 0.125,0.167 10 false 1 3.406,5.073 3.531,5.24 0.125,0.167 10 false 4 4.354,4.74 4.479,4.906 0.125,0.167 10 false 3 4.354,5.073 4.479,5.24 0.125,0.167 10 false 2 3.24,5.51 3.542,5.667 0.302,0.156 10 false C73 3.24,5.656 4.385,5.896 1.146,0.24 10 false No. 4 Ignition Coil 0.938,3.229 1.229,3.406 0.292,0.177 10 false G9 0.938,3.375 1.875,3.667 0.938,0.292 10 false Ignition Switch 0.552,1.979 0.823,2.229 0.271,0.25 10 false INJ 0.51,2.927 0.677,3.104 0.167,0.177 10 false 6 0.51,3.719 0.635,3.896 0.125,0.177 10 false 5 0.51,3.135 0.823,3.333 0.313,0.198 10 false IG2 0.51,3.51 0.833,3.677 0.323,0.167 10 false AM2 0.573,4.74 0.938,4.927 0.365,0.188 10 false AM2 0.719,6.052 1.219,6.281 0.5,0.229 10 false Battery 3.938,2.083 4.271,2.24 0.333,0.156 10 false IGT2 4.01,2.417 4.281,2.573 0.271,0.156 10 false IGF 3.604,2.083 3.833,2.24 0.229,0.156 10 false +B 3.604,2.417 3.958,2.573 0.354,0.156 10 false GND 3.948,3.448 4.281,3.604 0.333,0.156 10 false IGT3 4.01,3.792 4.281,3.948 0.271,0.156 10 false IGF 3.615,3.448 3.844,3.604 0.229,0.156 10 false +B 3.615,3.781 3.969,3.938 0.354,0.156 10 false GND 3.948,4.844 4.281,5.01 0.333,0.167 10 false IGT4 4.01,5.167 4.281,5.344 0.271,0.177 10 false IGF 3.615,4.833 3.844,4.99 0.229,0.156 10 false +B 3.615,5.167 3.969,5.323 0.354,0.156 10 false GND

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)
a.
A157860
0.396,2.073 0.813,2.365 0.417,0.292 0.396,2.406 0.813,2.698 0.417,0.292 0.396,1.406 0.813,1.698 0.417,0.292 0.396,1.74 0.813,2.031 0.417,0.292 1.323,2.125 1.094,2.844 true 2.104,2.146 2.354,2.844 true 0.115,0.094 0.313,0.281 0.198,0.188 10 false *a 0.469,1.469 0.75,1.615 0.281,0.146 10 false C70 0.479,1.802 0.76,1.948 0.281,0.146 10 false C71 0.479,2.135 0.76,2.281 0.281,0.146 10 false C72 0.479,2.479 0.76,2.625 0.281,0.146 10 false C73 0.979,2.875 1.208,3.042 0.229,0.167 10 false +B 2.229,2.865 2.583,3.031 0.354,0.167 10 false GND
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C70-4 (GND) - Body ground Always Below 1 Ω
C71-4 (GND) - Body ground Always Below 1 Ω
C72-4 (GND) - Body ground Always Below 1 Ω
C73-4 (GND) - Body ground Always Below 1 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C70-1 (+B) - C70-4 (GND) Ignition switch ON 11 to 14 V
C71-1 (+B) - C71-4 (GND) Ignition switch ON 11 to 14 V
C72-1 (+B) - C72-4 (GND) Ignition switch ON 11 to 14 V
C73-1 (+B) - C73-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL - ECM)
a.

Disconnect the ignition coil connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C70-2 (IGF) - C75-23 (IGF1) Always Below 1 Ω
C71-2 (IGF) - C75-23 (IGF1) Always Below 1 Ω
C72-2 (IGF) - C75-23 (IGF1) Always Below 1 Ω
C73-2 (IGF) - C75-23 (IGF1) Always Below 1 Ω
C70-3 (IGT1) - C75-17 (IGT1) Always Below 1 Ω
C71-3 (IGT2) - C75-16 (IGT2) Always Below 1 Ω
C72-3 (IGT3) - C75-15 (IGT3) Always Below 1 Ω
C73-3 (IGT4) - C75-14 (IGT4) Always Below 1 Ω
C70-2 (IGF) or C75-23 (IGF1) - Body ground Always 10 kΩ or higher
C71-2 (IGF) or C75-23 (IGF1) - Body ground Always 10 kΩ or higher
C72-2 (IGF) or C75-23 (IGF1) - Body ground Always 10 kΩ or higher
C73-2 (IGF) or C75-23 (IGF1) - Body ground Always 10 kΩ or higher
C70-3 (IGT1) or C75-17 (IGT1) - Body ground Always 10 kΩ or higher
C71-3 (IGT2) or C75-16 (IGT2) - Body ground Always 10 kΩ or higher
C72-3 (IGT3) or C75-15 (IGT3) - Body ground Always 10 kΩ or higher
C73-3 (IGT4) or C75-14 (IGT4) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Shuffle the arrangement of the ignition coil assemblies (among the No. 1 to No. 4 cylinders).

NOTICE:

Do not shuffle the connectors.



f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Check the DTCs output on the intelligent tester.

Powertrain > Engine > Trouble Codes
50001 61
Result:
Result Proceed to
Same DTC is output A
Different ignition coil DTC is output B




A

B