Home › Engine / Hybrid System › 2TR-FE ENGINE CONTROL › SFI SYSTEM
RM1880E _51 Engine / Hybrid System _013209 2TR-FE ENGINE CONTROL _0068463 SFI SYSTEM J

2TR-FE ENGINE CONTROL  SFI SYSTEM  ECM Back-up Power Source Circuit  


DESCRIPTION

While the ignition switch is off, battery voltage is supplied to terminal BATT of the ECM for the DTC memory, air-fuel ratio adaptive control value memory, etc.

WIRING DIAGRAM

A247776
0.906,2.531 1.573,2.75 0.667,0.219 10 false Battery 1.781,0.917 2.531,1.25 0.75,0.333 10 false BATT P/I 3.99,0.906 4.531,1.156 0.542,0.25 10 false EFI 5.604,0.563 5.802,0.76 0.198,0.198 10 false 3 5.51,0.75 5.906,0.927 0.396,0.177 10 false G89 5.573,1.885 5.719,2.063 0.146,0.177 10 false 3 5.5,2.063 5.844,2.24 0.344,0.177 10 false C75 5.865,0.917 6.313,1.167 0.448,0.25 10 false BATT 5.865,2.073 6.198,2.344 0.333,0.271 10 false E1 6.188,2.927 6.604,3.156 0.417,0.229 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.

Disconnect the ECM connector.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G89-3 (BATT) - Positive (+) battery cable terminal Always Below 1 Ω
G89-3 (BATT) or positive (+) battery cable terminal - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT BATTERY
a.

Check that the battery is not depleted.

Click herePower Source / Network>2TR-FE BATTERY / CHARGING>CHARGING SYSTEM>ON-VEHICLE INSPECTION

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

3.CHECK BATTERY TERMINAL

NG

REPLACE BATTERY

3.CHECK BATTERY TERMINAL
a.

Check that the battery terminals are not loose or corroded.

OK:

Battery terminals are not loose or corroded.



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (BATT VOLTAGE)

NG

REPAIR BATTERY TERMINAL

4.CHECK ECM (BATT VOLTAGE)
a.
A247761
0.667,0.917 1.083,1.167 0.417,0.25 2.333,0.917 2.75,1.167 0.417,0.25 0.865,1.531 0.865,2.448 0.865,2.448 1.031,2.448 true 2.698,1.531 2.698,2.448 2.698,2.448 2.5,2.448 true 0.271,0.188 0.583,0.385 0.313,0.198 10 *a 1.083,2.333 1.896,2.75 0.813,0.417 10 3 (E1) 1.917,2.354 2.729,2.771 0.813,0.417 10 3 (BATT) 0.75,0.958 1.563,1.375 0.813,0.417 10 C75 2.417,0.958 3.229,1.375 0.813,0.417 10 G89
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G89-3 (BATT) - C75-3 (E1) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG