Home › Engine / Hybrid System › 2TR-FE ENGINE MECHANICAL › ENGINE UNIT
RM1880E _51 Engine / Hybrid System _013210 2TR-FE ENGINE MECHANICAL _0068471 ENGINE UNIT G

2TR-FE ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 1.INSPECT CHAIN SUB-ASSEMBLY

a.
A101905C02
0.635,1.813 0.76,2.01 0.125,0.198 10 false 1 0.823,1.813 0.948,2.01 0.125,0.198 10 false 2 1.01,1.813 1.125,2.01 0.115,0.198 10 false 3 1.177,1.813 1.313,2.01 0.135,0.198 10 false 4 1.552,1.813 1.688,2.01 0.135,0.198 10 false 6 2.938,1.792 3.146,1.99 0.208,0.198 10 false 16 1.365,1.813 1.5,2.01 0.135,0.198 10 false 5 1.74,1.063 2.021,1.302 0.281,0.24 10 false *1
*1 Measuring Area


Pull the chain with a force of 147 N (15 kgf, 33.0 lbf) as shown in the illustration.


b.

Using a vernier caliper, measure the length of 16 links.

Maximum chain elongation:

147.5 mm (5.81 in.)


If the elongation is more than the maximum, replace the chain sub-assembly.

NOTICE:

Perform the measurement at 3 random places.



Hide 2.INSPECT NO. 2 CHAIN SUB-ASSEMBLY

a.

Pull the chain with a force of 147 N (15 kgf, 33.0 lbf).


b.

Using a vernier caliper, measure the length of 16 links.

Maximum chain elongation:

123.6 mm (4.87 in.)


If the elongation is more than the maximum, replace the No. 2 chain sub-assembly.

NOTICE:

Perform the measurement at 3 random places.



Hide 3.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A097905C03
2.229,0.771 2.458,0.427 2.458,0.427 2.531,0.427 false 1.458,1.604 1.729,1.885 1.729,1.885 1.854,1.885 true 2.594,0.313 2.948,0.51 0.354,0.198 10 false *1 1.906,1.781 2.125,1.979 0.219,0.198 10 false *2
*1 Plunger
*2 Stopper Plate


Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.


Hide 4.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A101971C01
0.865,1.135 0.625,0.698 0.625,0.698 0.521,0.698 false 1.51,0.583 1.74,0.146 1.74,0.146 1.823,0.146 false 0.323,0.594 0.51,0.792 0.188,0.198 10 false *1 1.885,0.042 2.063,0.24 0.177,0.198 10 false *2
*1 Plunger
*2 Stopper Plate


Move the stopper plate downward to release the lock. Push the plunger and check that it moves smoothly.


Hide 5.INSPECT CAMSHAFT TIMING SPROCKET

a.
A097906C06
0.906,0.271 1.125,0.271 false 3.198,2 3.406,2.156 0.208,0.156 10 false -
V100145

Worn Area


Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

Minimum distance:

1.0 mm (0.0394 in.)


If the distance is less than the minimum, replace the camshaft timing sprocket.

If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.


b.

Wrap the chain around the sprocket.


c.

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

113.8 mm (4.48 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and camshaft timing sprocket.


Hide 6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.
A097907C06
3.219,2.01 3.396,2.156 0.177,0.146 10 false -
V100145

Worn Area


Measure the distance between the most worn out timing gear tip and the beginning of the worn area below the tip.

Minimum distance:

1.0 mm (0.0394 in.)


If the distance is less than the minimum, replace the camshaft timing gear assembly.

If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.


b.

Wrap the chain around the timing gear.


c.

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum timing gear diameter (with chain):

113.8 mm (4.48 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and camshaft timing gear assembly.


Hide 7.INSPECT CRANKSHAFT TIMING SPROCKET

a.
A097908C06
0.917,0.438 1.042,0.438 false 3.271,1.979 3.385,2.135 0.115,0.156 10 false -
V100145

Worn Area


Measure the distance between the most worn out sprocket tip and the beginning of the worn area below the tip.

Minimum distance:

1.0 mm (0.0394 in.)


If the distance is less than the minimum, replace the crankshaft timing sprocket.

If the worn area is too small or difficult to distinguish from a normal area, perform the following 2 steps.


b.

Wrap the chain around the timing sprocket.


c.

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

59.4 mm (2.34 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and crankshaft timing sprocket.


Hide 8.INSPECT CHAIN TENSIONER SLIPPER

a.
A097909C02
1.458,0.792 1.698,1.01 0.24,0.219 10 false *1
*1 Wear


Using a vernier caliper, measure the tensioner slipper wear.

Maximum wear:

2.0 mm (0.0787 in.)


If the wear is more than the maximum, replace the chain tensioner slipper.


Hide 9.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A097910C02
1.375,0.958 1.573,1.156 0.198,0.198 10 false *1
*1 Wear


Using a vernier caliper, measure the vibration damper wear.

Maximum wear:

2.0 mm (0.0787 in.)


If the wear is more than the maximum, replace the No. 1 chain vibration damper.


Hide 10.INSPECT TIMING CHAIN GUIDE

a.
A097911C06
0.76,1.667 0.948,1.615 false 3.281,2.01 3.396,2.167 0.115,0.156 10 false -
V100145

Wear


Using a vernier caliper, measure the chain guide wear.

Maximum wear:

0.5 mm (0.0197 in.)


If the wear is more than the maximum, replace the timing chain guide.


Hide 11.INSPECT NO. 2 CRANKSHAFT TIMING SPROCKET

a.

Wrap the chain around the sprocket.


b.
A101907

Using a vernier caliper, measure the sprocket diameter with the chain.

Minimum sprocket diameter (with chain):

96.7 mm (3.81 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and No. 2 crankshaft timing sprocket.


Hide 12.INSPECT BALANCE SHAFT DRIVE GEAR SUB-ASSEMBLY

a.

Wrap the chain around the drive gear.


b.
A101906

Using a vernier caliper, measure the drive gear diameter with the chain.

Minimum drive gear diameter (with chain):

75.9 mm (2.99 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the chain and balance shaft drive gear sub-assembly.


Hide 13.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A101337C01
1.76,1.396 1.948,1.594 0.188,0.198 10 false *1
*1 Wear


Using a vernier caliper, measure the vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the No. 2 chain vibration damper.


Hide 14.INSPECT NO. 3 CHAIN VIBRATION DAMPER

a.
A068741C01
1.563,1.135 1.844,1.344 0.281,0.208 10 false *1
*1 Wear


Using a vernier caliper, measure the vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the No. 3 chain vibration damper.


Hide 15.INSPECT NO. 4 CHAIN VIBRATION DAMPER

a.
A068742C01
1.542,1.104 1.771,1.313 0.229,0.208 10 false *1
*1 Wear


Using a vernier caliper, measure the vibration damper wear.

Maximum wear:

1.0 mm (0.0394 in.)


If the wear is more than the maximum, replace the No. 4 chain vibration damper.


Hide 16.INSPECT CYLINDER HEAD SET BOLT

a.
A170594C02
2.042,1.25 2.24,1.458 0.198,0.208 10 false *1 2.646,1.25 2.844,1.458 0.198,0.208 10 false *2
*1 Measuring area
*2 Distance


Using a vernier caliper, measure the diameter of the most elongated threads in the measuring area.

Standard outside diameter:

10.76 to 10.97 mm (0.424 to 0.432 in.)


Minimum outside diameter:

10.40 mm (0.409 in.)


Distance:

30 mm (1.18 in.)


If a visual check reveals no excessively thin areas, check the center of the measuring area (see illustration) and find the area that has the smallest diameter.

If the diameter is less than the minimum, replace the cylinder head set bolt.


Hide 17.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the lash adjuster free from dirt and foreign objects.

·

Only use clean engine oil.



a.
A302788C01
0.948,0.469 1.271,0.323 1.271,0.323 1.49,0.323 true 2.458,0.469 2.167,0.323 2.167,0.323 1.979,0.323 true 1.094,1.146 1.417,0.885 1.417,0.885 1.615,0.885 true 2.406,1.031 2.115,0.885 2.115,0.885 1.927,0.885 true 1.104,1.385 1.438,1.115 1.438,1.115 1.635,1.115 true 2.375,1.26 2.083,1.115 2.083,1.115 1.896,1.115 true 1.406,3.365 1.115,3.219 1.115,3.219 0.927,3.219 true 0.948,1.771 1.281,1.5 1.281,1.5 1.552,1.5 true 2.49,1.646 2.229,1.5 2.229,1.5 1.896,1.5 true 0.875,2.271 1.208,2 1.208,2 1.625,2 true 2.604,2.24 2.219,2.01 2.219,2.01 1.99,2.01 true 1.073,2.396 1.385,2.198 1.385,2.198 1.615,2.198 true 2.406,2.406 2.188,2.208 2.188,2.208 1.969,2.208 true 1.698,0.802 2.01,0.958 0.313,0.156 10 false *1 1.698,1.042 2.01,1.198 0.313,0.156 10 false *2 1.708,1.427 2.021,1.583 0.313,0.156 10 false *3 1.74,1.917 2.052,2.073 0.313,0.156 10 false *4 1.76,2.146 2.073,2.302 0.313,0.156 10 false *5 0.771,2.604 1.083,2.76 0.313,0.156 10 false *a 2.542,2.615 2.854,2.771 0.313,0.156 10 false *b 1.604,0.25 2.063,0.448 0.458,0.198 10 false SST 0.615,3.146 1.073,3.344 0.458,0.198 10 false SST
*1 Tapered Part
*2 Plunger
*3 Low Pressure Chamber
*4 Check Ball
*5 High Pressure Chamber
*a CORRECT
*b INCORRECT


Place the lash adjuster into a container full of new engine oil.


b.

Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.



e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger can be pressed 3 times.


If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster with a new one.


Hide 18.INSPECT CAMSHAFT

a.

Check the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.



b.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

42.855 to 42.955 mm (1.687 to 1.691 in.)


Minimum cam lobe height:

42.855 mm (1.687 in.)


If the cam lobe height is less than the minimum, replace the camshaft.


c.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 35.949 to 35.965 mm (1.415 to 1.416 in.)
Other journal 26.959 to 26.975 mm (1.061 to 1.062 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 19.INSPECT NO. 2 CAMSHAFT

a.

Check the camshaft runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the circle runout at the center journal.

Maximum circle runout:

0.03 mm (0.00118 in.)


If the circle runout is more than the maximum, replace the camshaft.



b.

Using a micrometer, measure the cam lobe height.

Standard cam lobe height:

42.854 to 42.954 mm (1.687 to 1.691 in.)


Minimum cam lobe height:

42.854 mm (1.687 in.)


If the cam lobe height is less than the minimum, replace the camshaft.


c.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 35.949 to 35.965 mm (1.415 to 1.416 in.)
Other journal 26.959 to 26.975 mm (1.061 to 1.062 in.)


If the journal diameter is not as specified, check the oil clearance.


Hide 22.INSPECT EXHAUST MANIFOLD

a.
A222420

Using a precision straightedge and feeler gauge, measure the warpage of the surface that contacts the cylinder head.

Maximum warpage:

0.7 mm (0.0276 in.)


If the warpage is more than the maximum, replace the exhaust manifold.