1.INSPECT CYLINDER HEAD SUB-ASSEMBLY
Using a precision straightedge and feeler gauge, measure the warpage of the surfaces that contact the cylinder block and manifolds.
| *a | Cylinder Head Lower Side | *b | Intake Manifold Side |
| *c | Exhaust Manifold Side | - | - |
0.05 mm (0.00197 in.)
If the warpage is more than the maximum, replace the cylinder head.
Using a dye penetrant, check the intake ports, exhaust ports and cylinder head surface for cracks.
If cracked, replace the cylinder head.
2.INSPECT INNER COMPRESSION SPRING
Using a vernier caliper, measure the free length of the inner compression spring.
48.53 mm (1.91 in.)
If the free length is not as specified, replace the spring.
| *1 | Deviation |
Using a steel square, measure the deviation of the inner compression spring.
1.5 mm (0.0591 in.)
2°
If the deviation is more than the maximum, replace the spring.
3.INSPECT INTAKE VALVE
Using a vernier caliper, measure the overall length of the valve.
106.26 mm (4.18 in.)
105.96 mm (4.17 in.)
If the overall length is less than the minimum, replace the intake valve.
Using a micrometer, measure the diameter of the valve stem.
5.470 to 5.485 mm (0.215 to 0.216 in.)
| *1 | Margin Thickness |
Using a vernier caliper, measure the valve head margin thickness.
1.05 to 1.45 mm (0.0413 to 0.0571 in.)
0.50 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the intake valve.
4.INSPECT EXHAUST VALVE
Using a vernier caliper, measure the overall length of the valve.
106.74 mm (4.20 in.)
106.44 mm (4.19 in.)
If the overall length is less than the minimum, replace the exhaust valve.
Using a micrometer, measure the diameter of the valve stem.
5.465 to 5.480 mm (0.215 to 0.216 in.)
| *1 | Margin Thickness |
Using a vernier caliper, measure the valve head margin thickness.
1.2 to 1.6 mm (0.0472 to 0.0630 in.)
0.50 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the exhaust valve.
5.INSPECT VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Do not rotate the valve while pressing the valve against the valve seat.
| *1 | Width |
Check the valve face and valve seat by using the following procedure.
Check that Prussian blue appears around the entire valve face. If not, replace the valve.
Check that Prussian blue appears around the entire valve seat. If so, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the valve seat contacts the middle of the valve face with the width between 1.1 and 1.4 mm (0.0433 and 0.0551 in.).
6.INSPECT CAMSHAFT THRUST CLEARANCE
Install the camshafts (See page Engine / Hybrid System>2TR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION).
Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.
0.10 to 0.24 mm (0.00394 to 0.00945 in.)
0.26 mm (0.0102 in.)
If the thrust clearance is more than the maximum, replace the cylinder head. If the thrust surface is damaged, replace the camshaft.
7.INSPECT CAMSHAFT OIL CLEARANCE
Clean the bearing caps and camshaft journals.
Place the camshafts on the cylinder head.
| *1 | Plastigage |
Lay a strip of Plastigage across each of the camshaft journals.
Install the bearing caps (See page Engine / Hybrid System>2TR-FE ENGINE MECHANICAL>CAMSHAFT>INSTALLATION).
Do not turn the camshafts.
Remove the bearing caps (See page Engine / Hybrid System>2TR-FE ENGINE MECHANICAL>CAMSHAFT>REMOVAL).
| *1 | Plastigage |
Measure the Plastigage at its widest point.
| Item | Specified Condition |
|---|---|
| No. 1 journal | 0.035 to 0.072 mm (0.00138 to 0.00283 in.) |
| Other journals | 0.025 to 0.062 mm (0.000984 to 0.00244 in.) |
0.08 mm (0.00315 in.)
If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the cylinder head sub-assembly.
Completely remove the Plastigage.
8.INSPECT VALVE GUIDE BUSH OIL CLEARANCE
Using a caliper gauge, measure the inside diameter of the guide bush.
5.51 to 5.53 mm (0.217 to 0.218 in.)
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Specified Condition |
|---|---|
| Intake | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
|---|---|
| Intake | 0.08 mm (0.00315 in.) |
| Exhaust | 0.10 mm (0.00397 in.) |
If the clearance is more than the maximum, replace the valve and valve guide bush.