Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL PUMP
RM1880E _51 Engine / Hybrid System _013211 2TR-FE FUEL _0068479 FUEL PUMP A

2TR-FE FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.

Apply a light coat of gasoline or grease to a new gasket, and install the gasket to the fuel tank.


b.

Install the fuel suction with pump and gauge tube to the fuel tank.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge.



Hide 2.INSTALL FUEL PUMP GAUGE RETAINER

a.

Set the fuel pump gauge retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer one complete turn by hand.


b.
A246112
1.167,2.75 0.938,2.75 false 0.5,3.083 0.677,3.083 true 0.5,2.167 0.583,2.167 0.583,2.167 0.656,2.271 false 2.917,1.667 2.542,1.073 true 2.844,1.688 3.26,1.979 0.417,0.292 10 false SST 0.344,3 0.688,3.26 0.344,0.26 10 false *3 1.198,2.667 1.542,2.948 0.344,0.281 10 false *2 0.344,2.094 0.646,2.365 0.302,0.271 10 false *1
*1 SST (Plate)
*2 SST (Claw)
*3 Rib


Temporarily install SST (plate and 4 claws) to the fuel pump gauge retainer.

SST
09808-14030  

HINT:
·

Be sure to use 4 SST (claws) as shown in the illustration.

·

Engage SST (claws) securely with the fuel pump gauge retainer ribs to secure SST.




c.

While pressing SST (claws) against the fuel pump gauge retainer ribs securely, install the 4 bolts.

HINT:

Install SST while pressing SST (claws) against the fuel pump gauge retainer (toward the center of SST).



d.

Install SST (handle).


e.
A302876
2.729,0.656 2.833,0.167 2.833,0.167 2.917,0.167 true 1.219,0.656 0.667,1.417 0.667,1.417 0.583,1.417 true 2,2.979 2.083,2.667 2.083,2.667 2.167,2.667 false 1.302,3.219 1,2.75 1,2.75 0.917,2.75 true 2.969,0.094 3.333,0.333 0.365,0.24 10 false SST 0.292,1.333 0.75,1.667 0.458,0.333 10 false SST 1.979,3.135 2.25,3.417 0.271,0.281 10 false A 2.75,3.438 3.083,3.75 0.333,0.313 10 false B 0.75,2.677 1.021,2.875 0.271,0.198 10 false *1 2.229,2.604 2.5,2.802 0.271,0.198 10 false *2
*1 Retainer Mark
*2 Fuel Tank Mark


Using SST, tighten the retainer until the mark on the retainer aligns with mark A on the fuel tank as shown in the illustration.

SST
09808-14030  

NOTICE:
·

Do not use any tools other than those specified in this operation. Damage to the fuel pump gauge retainer or fuel tank may result.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If SST (handle) is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolts) and reinstall SST.



HINT:
·

If the alignment is difficult, make sure the mark on the retainer is within range B on the fuel tank.

·

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing SST, rotate the handle slowly to tighten the fuel pump gauge retainer.

·

The tips of SST (claws) can be fitted onto the ribs of the fuel pump gauge retainer.




f.

Install the fuel tank return tube and fuel tank main tube to the fuel tank.


g.
A252105
1.167,0.167 1.25,0.167 1.25,0.167 1.313,0.583 false 2.167,0.167 2.083,0.167 2.083,0.167 1.865,0.573 false 2.417,0.583 2.333,0.583 2.333,0.583 2.115,0.906 false 1.573,1.146 1.156,1.146 1.156,1.146 1.156,1.781 true 1.563,1.281 1.167,1.281 true 0.99,0.094 1.344,0.344 0.354,0.25 10 false *1 2.219,4.354 2.51,4.594 0.292,0.24 10 false *b 0.75,4.354 1.052,4.594 0.302,0.24 10 false *a 1.094,1.823 1.5,2.083 0.406,0.26 10 false *4 2.479,0.51 2.823,0.729 0.344,0.219 10 false *3 2.208,0.094 2.542,0.344 0.333,0.25 10 false *2
*1 Fuel Tube
*2 Fuel Tube Joint
*3 Tube Joint Clip
*4 O-Ring
*a CORRECT
*b INCORRECT


Install the 2 fuel tank tubes with the 2 tube joint clips.

NOTICE:
·

Check that there are no scratches or foreign objects on the connecting parts.

·

Check that the fuel tube joints are inserted securely.

·

Check that the tube joint clips are on the collars of the fuel tube joints.

·

After installing the tube joint clips, check that the fuel tube joints have not been pulled off.




Hide 3.INSTALL FUEL TANK ASSEMBLY