Home › Engine / Hybrid System › 2TR-FE FUEL › FUEL TANK
RM1880E _51 Engine / Hybrid System _013211 2TR-FE FUEL _0068480 FUEL TANK A

2TR-FE FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL TANK TO FILLER PIPE HOSE

a.

Install the fuel tank to filler pipe hose to the fuel tank.


Hide 2.INSTALL FUEL TANK BREATHER HOSE

a.

Install the fuel tank breather hose to the fuel tank.


Hide 3.INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

Hide 5.INSTALL VENT LINE TUBE

a.

Connect the vent line hose and install the vent line tube.


Hide 6.INSTALL FUEL TANK CUSHION

a.

Install 2 new fuel tank cushions.


Hide 7.INSTALL NO. 1 FUEL TANK HEAT INSULATOR

a.

Install the No. 1 fuel tank heat insulator with the 5 clips and 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 8.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank on an engine lifter and lift up the engine lifter.

A306739
5.552,1.698 6.042,1.698 false 5.052,2.427 5.292,2.427 true 6.115,1.604 6.427,1.76 0.313,0.156 10 false *1 4.854,2.344 5.167,2.5 0.313,0.156 10 false *2 5.792,2.24 6.104,2.396 0.313,0.156 10 false *3
*1 Fuel Tank Cushion *2 Wire Harness
*3 Fuel Tank - -


NOTICE:
·

Do not allow the fuel tank to contact the vehicle, especially the differential.

·

Be careful not to cut the wiring.




b.

Fold back the 2 cushions rubbers.


c.

Attach the wire harness to the 4 clamps and connect the fuel pump and sender gauge connector.

NOTICE:

Be careful not to cut the wiring.



d.

Install the 3 fuel tank bands with the 3 pins and 3 clips.


e.

Connect the 3 fuel tank bands with the 3 bolts.

Torque:
61 N*m (622 kgf*cm, 45 ft.*lbf)


Hide 9.INSTALL FUEL TANK INLET PIPE SUB-ASSEMBLY

a.

Install the fuel tank inlet pipe with the bolt and nut.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 10.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.

Connect the fuel tank to filler pipe hose to the fuel tank inlet pipe.


Hide 11.CONNECT FUEL TANK BREATHER HOSE

a.

Attach the breather hose to the 2 clamps.


b.

Connect the fuel tank breather hose to the fuel tank inlet pipe.


Hide 12.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY AND FUEL TANK RETURN TUBE

a.

Connect the fuel tank main tube (See page Engine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION).


b.

Connect the fuel tank return tube (See page Engine / Hybrid System>2TR-FE FUEL>FUEL SYSTEM>PRECAUTION).


c.

Connect the vent line hose to the fuel pipe.


Hide 13.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the 2 tube clamps to the fuel tube.


Hide 14.INSTALL FUEL TANK CAP ASSEMBLY

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).