Home › Drivetrain › A343E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1880E _52 Drivetrain _013217 A343E AUTOMATIC TRANSMISSION / TRANSAXLE _0068504 AUTOMATIC TRANSMISSION SYSTEM J

A343E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  Stop Light Switch Circuit  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends signals to the ECM. Then the ECM cancels the operation of the lock-up clutch during braking.

WIRING DIAGRAM

C146704
5.719,3.052 6.167,3.438 0.448,0.385 10 false ECM 5.719,2.854 6.167,3.177 0.448,0.323 10 false G88 5.531,1.323 5.927,1.698 0.396,0.375 10 false STP 3.833,1.677 4.156,1.896 0.323,0.219 10 false A24 3.833,1.875 4.979,2.344 1.146,0.469 10 false Stop Light Switch 3.01,1.531 3.5,1.854 0.49,0.323 10 false STOP 2.083,1.531 2.458,1.906 0.375,0.375 10 false ALT 5.292,1.458 5.448,1.667 0.156,0.208 10 false 4 4.729,1.458 4.885,1.667 0.156,0.208 10 false 1 3.938,1.458 4.094,1.667 0.156,0.208 10 false 2 1.646,2.375 2.156,2.76 0.51,0.385 10 false Battery

CAUTION / NOTICE / HINT

DATA LIST


HINT:

Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

According to the display on the intelligent tester, read the Data List.

Powertrain > Engine > Data List
Tester Display
Stop Light Switch
50003 61 188
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status ON or OFF
·

Brake pedal depressed: ON

·

Brake pedal released: OFF


-


PROCEDURE

1.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


b.
C228781
0.74,3 0.635,2.458 0.635,2.458 0.469,2.458 false 1.542,1.323 1.021,1.677 true 1.896,1.323 2.427,1.677 true 1.844,1.125 2.427,0.771 true 1.594,1.125 1.021,0.771 true 0.875,0.667 1,0.865 0.125,0.198 10 false 2 2.469,0.656 2.604,0.854 0.135,0.198 10 false 1 0.896,1.615 1.021,1.813 0.125,0.198 10 false 4 2.479,1.615 2.625,1.813 0.146,0.198 10 false 3 0.344,3.771 0.531,3.969 0.188,0.198 10 false *b 1,3.76 1.188,3.958 0.188,0.198 10 false *c 0.313,2.385 0.5,2.583 0.188,0.198 10 false *1 0.063,0.073 0.375,0.271 0.313,0.198 10 false *a
*1 Pin
*a Component without harness connected
(Stop Light Switch Assembly)
*b Not pushed
*c Pushed


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
3 - 4 Pin pushed Below 1 Ω
1 - 2 Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (BATTERY - ECM)
a.

Disconnect the G88 ECM connector.


b.
C237530
1.802,0.573 2.24,0.833 0.438,0.26 1.698,2.708 2,1.865 true 0.063,0.031 0.375,0.229 0.313,0.198 10 false *a 1.479,2.771 2.167,2.969 0.688,0.198 10 false 4 (STP) 1.875,0.615 2.25,0.844 0.375,0.229 10 false G88
*a Rear view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G88-4 (STP) - Body ground Brake pedal depressed 11 to 14 V
G88-4 (STP) - Body ground Brake pedal released Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR