Home › Drivetrain › A343E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1880E _52 Drivetrain _013217 A343E AUTOMATIC TRANSMISSION / TRANSAXLE _0068504 AUTOMATIC TRANSMISSION SYSTEM C

A343E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2716  Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT)  


DESCRIPTION

C237837
5.74,2.177 5.854,2.521 5.854,2.521 5.927,2.521 true 4.896,1.917 4.677,1.281 4.677,1.281 4.615,1.281 true 5.146,2.052 5.01,2.469 5.01,2.469 4.938,2.469 true 5.979,2.448 6.865,2.667 0.885,0.219 10 false Solenoid Coil 0.26,0.448 1.51,0.667 1.25,0.219 10 false Hydraulic Pressure 4.458,2.375 4.99,2.594 0.531,0.219 10 false Sleeve 3.833,1.198 4.677,1.417 0.844,0.219 10 false Spool Valve 2.75,2.979 3.313,3.198 0.563,0.219 10 false Current

Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The ECM adjusts the current of shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2716 Pressure Control Solenoid "D" Electrical (Shift Solenoid Valve SLT) Open or short is detected in the shift solenoid valve SLT circuit for 1 second or more while driving (1-trip detection logic).
·

Open or short in shift solenoid valve SLT circuit

·

Shift solenoid valve SLT

·

ECM


- DTC stored

HINT:
·

MIL: "Comes on" means the Malfunction Indicator Lamp (MIL) illuminates.

·

Memory: "DTC stored" means the TCM stores the trouble code if the TCM detects the DTC detection condition.



MONITOR DESCRIPTION

When an open or short in the shift solenoid valve SLT circuit is detected, the ECM interprets this as a fault. The ECM will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C214969
1.771,2.865 3.104,3.063 1.333,0.198 10 false Transmission Wire 1.76,2.688 2.156,2.885 0.396,0.198 10 false C92 5.615,1.25 6.115,1.448 0.5,0.198 10 false SLT+ 5.333,1.354 5.573,1.552 0.24,0.198 10 false 12 5.802,2.948 6.302,3.146 0.5,0.198 10 false C76 5.792,3.125 6.292,3.323 0.5,0.198 10 false ECM 3.469,1.146 3.969,1.344 0.5,0.198 10 false SLT+ 3.927,1.354 4.167,1.552 0.24,0.198 10 false 2 1.479,1.719 3.208,1.917 1.729,0.198 10 false Shift Solenoid Valve SLT 5.615,2.208 6.115,2.406 0.5,0.198 10 false SLT- 5.344,2.323 5.583,2.521 0.24,0.198 10 false 13 3.469,2.104 3.969,2.302 0.5,0.198 10 false SLT- 3.927,2.323 4.167,2.521 0.24,0.198 10 false 6 1.281,2.115 1.677,2.313 0.396,0.198 10 false 1 1.281,1.333 1.677,1.531 0.396,0.198 10 false 2

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SLT)
a.

Disconnect the C92 transmission wire connector.


b.
C214964
1.833,0.948 2.479,0.531 true 2.417,1.698 1.875,1.229 true 0.083,0.042 0.396,0.24 0.313,0.198 10 false *a 2.49,1.635 2.885,1.833 0.396,0.198 10 false SLT- 2.542,0.438 2.948,0.635 0.406,0.198 10 false SLT+
*a Component without harness connected
(Transmission Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (SLT+) - 6 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
2 (SLT+) - Body ground Always 10 kΩ or higher
6 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SLT
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C76 ECM connector.


b.
C237531
1.156,0.542 1.594,0.802 0.438,0.26 0.958,2.656 1.406,1.927 true 1.865,2.656 1.458,1.938 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 1.25,0.583 1.625,0.813 0.375,0.229 10 false C76 0.656,2.688 1.323,2.885 0.667,0.198 10 false 13 (SLT-) 1.677,2.677 2.365,2.875 0.688,0.198 10 false 12 (SLT+)
*a Rear view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C76-12 (SLT+) - C76-13 (SLT-) 20°C (68°F) 5.0 to 5.6 Ω
C76-12 (SLT+) - Body ground Always 10 kΩ or higher
C76-13 (SLT-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SLT
a.
C209928
1.75,0.969 2.198,0.385 true 1.479,0.958 1.021,0.375 true 1.76,2.948 2.208,2.354 true 1.479,2.948 1.021,2.354 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 2.24,0.25 2.406,0.448 0.167,0.198 10 false 1 0.917,0.24 1.083,0.438 0.167,0.198 10 false 2 2.25,2.198 2.417,2.396 0.167,0.198 10 false 1 0.917,2.229 1.083,2.427 0.167,0.198 10 false 2 1.927,3.969 2.125,4.167 0.198,0.198 10 false (-) 1.115,3.969 1.333,4.167 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLT)


Remove shift solenoid valve SLT.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG