Home › Drivetrain › A343E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM
RM1880E _52 Drivetrain _013217 A343E AUTOMATIC TRANSMISSION / TRANSAXLE _0068504 AUTOMATIC TRANSMISSION SYSTEM C

A343E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P2769  Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL)  P2770  Torque Converter Clutch Solenoid Circuit High (Shift Solenoid Valve SL)  


DESCRIPTION

The shift solenoid valve SL is turned on and off by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls the operation of the lock-up clutch.

Fail-safe function:

If the ECM detects a malfunction, it turns the shift solenoid valve SL off.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2769 Torque Converter Clutch Solenoid Circuit Low (Shift Solenoid Valve SL) ECM detects short in shift solenoid valve SL circuit (once) when shift solenoid valve SL is operated (1-trip detection logic)
·

Short in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

ECM


- DTC stored
P2770 Torque Converter Clutch Solenoid Circuit High (Shift Solenoid Valve SL) ECM detects open in shift solenoid valve SL circuit (once) when shift solenoid valve SL is not operated (1-trip detection logic)
·

Open in shift solenoid valve SL circuit

·

Shift solenoid valve SL

·

ECM


- DTC stored

HINT:
·

MIL: "Comes on" means the Malfunction Indicator Lamp (MIL) illuminates.

·

Memory: "DTC stored" means the TCM stores the trouble code if the TCM detects the DTC detection condition.



MONITOR DESCRIPTION

Torque converter lock-up is controlled by the ECM based on engine rpm, engine load, engine temperature, vehicle speed, transmission temperature, and shift position selection. The ECM determines the lock-up status of the torque converter by comparing the engine rpm (NE) to the input rpm (NC0). The ECM calculates the actual transmission gear by comparing the input rpm (NC0) to the output rpm (SP2). When conditions are appropriate, the ECM requests "lock-up" by applying control voltage to the shift solenoid valve SL. When the shift solenoid valve SL is opened, the shift solenoid valve SL applies pressure to the lock-up relay valve and locks the torque converter clutch. If the ECM detects an open or short in the shift solenoid valve SL circuit, the ECM interprets this as a fault in the shift solenoid valve SL or its circuit. The ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

C237838
2.469,0.844 2.896,1.344 0.427,0.5 10 false SL 5.74,0.844 6.073,1.135 0.333,0.292 10 false SL 1,1.729 2.646,2.271 1.646,0.542 10 false Shift Solenoid Valve SL 0.927,2.969 2.552,3.427 1.625,0.458 10 false Transmission Wire 0.927,2.771 1.5,3.135 0.573,0.365 10 false C92 5.969,3.302 6.51,3.75 0.542,0.448 10 false ECM 5.969,3.104 6.323,3.406 0.354,0.302 10 false C76 2.802,1.125 3.115,1.396 0.313,0.271 10 false 7 5.438,1.125 5.76,1.521 0.323,0.396 10 false 11

PROCEDURE

1.INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL)
a.

Disconnect the C92 transmission wire connector.


b.
C214964
1.083,1.677 1.552,1.229 true 0.073,0.042 0.385,0.24 0.313,0.198 10 false *a 0.896,1.688 1.125,1.885 0.229,0.198 10 false SL
*a Component without harness connected
(Transmission Wire)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL - ECM)

NG

3.INSPECT SHIFT SOLENOID VALVE SL
2.CHECK HARNESS AND CONNECTOR (SHIFT SOLENOID VALVE SL - ECM)
a.

Disconnect the C76 ECM connector.


b.
C237531
1.156,0.542 1.594,0.802 0.438,0.26 1.927,2.667 1.51,1.938 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 1.24,0.583 1.615,0.813 0.375,0.229 10 false C76 1.771,2.688 2.344,2.885 0.573,0.198 10 false 11 (SL)
*a Rear view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C76-11 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

3.INSPECT SHIFT SOLENOID VALVE SL
a.
C237973
0.094,0.094 0.344,0.313 0.25,0.219 10 false *a 3.063,0.49 3.302,0.708 0.24,0.219 10 false (+) 3.063,1.073 3.302,1.292 0.24,0.219 10 false (-)
*a Component without harness connected
(Shift Solenoid Valve SL)


Remove shift solenoid valve SL.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SL connector terminal - Shift solenoid valve SL body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SL connector

·

Battery negative (-) → Shift solenoid valve SL body


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

NG