Home › Drivetrain › A343E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM1880E _52 Drivetrain _013217 A343E AUTOMATIC TRANSMISSION / TRANSAXLE _0068515 AUTOMATIC TRANSMISSION UNIT A

A343E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 1.REMOVE DRAIN PLUG

a.

Remove the drain plug and gasket.


Hide 2.REMOVE BREATHER HOSE

C288835

a.

Remove the bolt and breather hose.


Hide 3.REMOVE TRANSMISSION CONTROL SHAFT LEVER LH

C280864

a.

Remove the nut, washer and control shaft lever.


Hide 4.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C241044

a.

Using a screwdriver, bend the tabs of the lock washer.


b.

Remove the nut and lock washer.


c.

Remove the bolt and park/neutral position switch.

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



Hide 5.REMOVE ATF TEMPERATURE SENSOR

C239915

a.

Detach the sensor connector clamp from the wire harness bracket.


b.

Using a 19 mm union nut wrench, remove the sensor from the transmission assembly.


c.

Remove the bolt and wire harness bracket.


d.

Remove the O-ring from the sensor.


Hide 6.REMOVE OIL COOLER TUBE UNION

G034863

a.

Remove the 2 tube unions.


b.

Remove the 2 O-rings from each tube union.


Hide 7.REMOVE SPEED SENSOR NC0

Q003894

a.

Remove the bolt and sensor.


b.

Remove the O-ring from the sensor.


Hide 8.REMOVE SPEEDOMETER SENSOR

a.
G035547

Remove the bolt and sensor.


b.

Remove the O-ring from the sensor.


Hide 9.REMOVE SPEED SENSOR SP2

G035548

a.

Remove the bolt and sensor.


b.

Remove the O-ring from the sensor.


Hide 10.REMOVE AUTOMATIC TRANSMISSION HOUSING

C220031

a.

Remove the 6 bolts.


b.

Remove the transmission housing.


Hide 11.SECURE TRANSMISSION CASE

AT05092

a.

Secure the transmission case to an overhaul attachment.


Hide 12.REMOVE EXTENSION HOUSING SUB-ASSEMBLY

D005548

a.

Remove the 6 bolts.


b.

Remove the extension housing and gasket.


Hide 13.REMOVE EXTENSION HOUSING BUSH APPLY TUBE

a.
AT04637
1.083,0.875 0.885,0.396 0.885,0.396 0.76,0.396 false 0.375,1.875 0.094,1.365 0.094,1.365 0.396,1.365 false 0.542,0.313 0.875,0.646 0.333,0.333 10 false *1 0.479,1.292 0.729,1.531 0.25,0.24 10 false *2
*1 Extension Housing Bush Apply Tube
*2 Extension Housing Bush Apply Tube Gasket


Remove the extension housing bush apply tube together with the extension housing bush apply tube gasket.


Hide 14.REMOVE EXTENSION HOUSING BUSH APPLY TUBE GASKET

a.

Remove the gasket from the extension housing bush apply tube.


Hide 15.REMOVE EXTENSION HOUSING DUST DEFLECTOR

D005579

a.

Secure the extension housing in a vise between aluminum plates.


b.

Using a screwdriver and hammer, tap off the dust deflector.


Hide 16.REMOVE AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

a.
C220032
1.479,0.625 1.156,0.292 1.156,0.292 0.958,0.292 true 0.729,0.198 1.021,0.5 0.292,0.302 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the oil seal.

NOTICE:

Be careful not to damage the automatic transmission extension housing.


HINT:

Tape the screwdriver tip before use.



Hide 17.REMOVE SPEEDOMETER DRIVE GEAR

C238171

a.

Using a snap ring expander, remove the snap ring.


b.

Remove the speedometer drive gear and the ball.


Hide 18.REMOVE SENSOR ROTOR

a.
C220512

Remove the sensor rotor and key.


b.

Using a snap ring expander, remove the snap ring.


Hide 19.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C238060

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with foreign matter located at the bottom of the oil pan.


a.

Remove the 19 bolts.


b.
C280841

Insert the blade of an oil pan seal cutter between the transmission case and oil pan, and then cut through the applied sealer.

NOTICE:

Be careful not to damage the flanges of the oil pan and transmission case.



c.

Remove the pan from the transmission case.


Hide 21.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

a.

Turn over the transmission.


b.
D028706

Remove the 4 bolts and valve body oil strainer from the valve body.


c.

Remove the 3 gaskets from the oil strainer.


Hide 22.REMOVE TRANSMISSION WIRE

C238020

a.

Disconnect the 4 connectors from the shift solenoid valves.


b.
C280843

Remove the bolt and stopper plate from the case.


c.

Pull out the transmission wire from the transmission case to remove it.


d.

Remove the O-ring from the transmission wire connector.


Hide 23.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

D029011

a.

Remove the 20 bolts and valve body.


Hide 24.REMOVE CHECK BALL BODY

AT04847
2.354,0.49 1.802,0.49 false 2.333,0.146 1.813,0.146 false 2.406,0.083 2.781,0.344 0.375,0.26 10 *1 2.427,0.427 2.896,0.74 0.469,0.313 10 *2
*1 Check Ball Body
*2 Spring


a.

Remove the check ball body and spring.


Hide 25.REMOVE B-2 ACCUMULATOR PISTON

D006514

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the B-2 accumulator piston and spring.

NOTICE:
·

The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.

·

Take care not to splash ATF when applying the compressed air.




b.

Remove the 2 O-rings from the piston.


Hide 26.REMOVE C-2 ACCUMULATOR PISTON

D006514

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the C-2 accumulator piston and 2 springs.

NOTICE:
·

The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.

·

Take care not to splash ATF when applying the compressed air.




b.

Remove the 2 O-rings from the piston.


Hide 27.REMOVE B-0 ACCUMULATOR PISTON

D006515

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the B-0 accumulator piston and spring.

NOTICE:
·

The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.

·

Take care not to splash ATF when applying the compressed air.




b.

Remove the 2 O-rings from the piston.


Hide 28.REMOVE C-0 ACCUMULATOR PISTON

D006516

a.

Apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole to remove the C-0 accumulator piston and 2 springs.

NOTICE:
·

The application of compressed air may cause the piston to jump out. When removing the piston, hold it using a piece of cloth.

·

Take care not to splash ATF when applying the compressed air.




b.

Remove the O-ring from the piston.


Hide 29.REMOVE PARKING LOCK PAWL BRACKET

C280867

a.

Remove the 3 bolts and bracket.


Hide 30.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

AT05120

a.

Disconnect the parking lock rod from the manual valve lever to remove it.


Hide 31.REMOVE PARKING LOCK PAWL

Z006720
1.271,1.396 0.625,0.24 0.625,0.24 0.49,0.24 true 1.396,1.427 1.844,1.979 1.844,1.979 1.979,1.979 true 1.01,1.656 1.323,1.99 1.323,1.99 1,1.99 true 2.021,0.375 2.177,0.135 2.177,0.135 2.281,0.135 true 2.354,0.083 3.063,0.427 0.708,0.344 10 *2 0.271,0.177 0.531,0.448 0.26,0.271 10 *1 0.802,1.917 1.125,2.104 0.323,0.188 10 *3 2.052,1.896 2.531,2.083 0.479,0.188 10 *4
*1 Parking Lock Pawl Shaft
*2 Lock Pawl
*3 Spring
*4 E-Ring


a.

Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.


b.

Remove the E-ring from the shaft.


Hide 32.REMOVE MANUAL VALVE LEVER SHAFT

Z006721
2.698,0.677 2.896,1.01 2.896,1.01 3,1.01 true 2.552,0.323 2.667,0.396 2.667,0.396 2.667,0.427 false 2.427,0.354 2.552,0.458 2.552,0.458 2.552,0.5 false 2.344,0.417 2.396,0.49 2.396,0.49 2.396,0.552 false 2.208,0.49 2.25,0.594 false 1.906,1.115 1.906,1.146 false 1.854,1.083 1.854,1.104 false 1.802,1.01 1.802,1.052 false 1.75,0.958 1.75,1.01 false 3.073,0.906 3.396,1.198 0.323,0.292 10 false *1
*1 Spacer


a.

Using a hammer and screwdriver, cut off the spacer and remove it from the shaft.


b.
AT05105

Using a pin punch and hammer, tap out the spring pin.

HINT:

Tap out the spring pin slowly so that it does not fall into the transmission case.



c.

Pull out the manual valve lever shaft through the case and remove the manual valve lever.


Hide 33.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C240211
0.417,0.677 0.479,0.677 0.479,0.677 0.74,1.083 false 3.083,0.542 3.01,0.542 3.01,0.542 2.688,0.938 true 0.229,0.594 0.479,0.771 0.25,0.177 10 false *1 3.115,0.458 3.365,0.635 0.25,0.177 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the 2 oil seals.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Tape the screwdriver tip before use.



Hide 34.REMOVE OIL PUMP ASSEMBLY

A306940

a.

Stand the transmission upright.


b.

Remove the 7 bolts from the transmission case.


c.
AT07874
1.292,0.885 0.563,0.708 true 0.26,0.615 0.646,0.823 0.385,0.208 10 false SST

Using SST, remove the oil pump.

SST
09610-20012  


d.

Remove the O-ring from the oil pump.


e.
AT08431

Remove the bearing race from the oil pump.


Hide 35.REMOVE OVERDRIVE PLANETARY GEAR ASSEMBLY WITH OVERDRIVE DIRECT CLUTCH AND OVERDRIVE 1-WAY CLUTCH ASSEMBLY

C212458

a.

Remove the planetary gear together with the direct clutch and 1-way clutch from the transmission case.


b.
C212459
2.75,1.01 2.833,1.354 2.833,1.354 2.927,1.354 false 0.615,1.563 0.698,1.906 0.698,1.906 0.781,1.906 false 0.854,1.823 1.115,2.073 0.26,0.25 10 false *1 3,1.271 3.271,1.583 0.271,0.313 10 false *2
*1 Bearing Race
*2 Bearing


Remove the bearing race and bearing.


Hide 37.REMOVE OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

C213736

Hide 38.REMOVE OVERDRIVE DIRECT CLUTCH DISC SET

a.
C237869
2.198,0.979 1.875,0.604 1.875,0.604 1.74,0.604 false 1.521,0.5 1.75,0.781 0.229,0.281 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring from the overdrive direct clutch drum.

NOTICE:

Be careful not to damage the overdrive direct clutch drum.


HINT:

Tape the screwdriver tip before use.



b.

Remove the flange, 2 discs and 2 plates.


Hide 40.REMOVE OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

C212482
1.167,0.469 0.865,0.25 0.865,0.25 0.719,0.25 false 2.49,0.802 2.948,0.802 true 0.354,0.167 1.115,0.5 0.76,0.333 10 false SST 3.052,0.708 3.417,0.917 0.365,0.208 10 false SST

a.

Place SST on the return spring and compress the return spring with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the clutch return spring.


Hide 41.INSPECT OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 42.REMOVE OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

AT03151

a.

Place the oil pump onto the torque converter, and then place the overdrive direct clutch onto the oil pump.


b.

Hold the overdrive direct clutch piston by hand and apply compressed air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil pump to remove the overdrive direct clutch piston.

HINT:

If the piston is at an angle and cannot be removed, press down on the protruding side and apply compressed air again.



c.

Remove the 2 O-rings from the piston.


Hide 45.REMOVE OVERDRIVE RETAINING PLATE

a.
C237778
1.979,1.26 2.25,1.01 2.25,1.01 2.385,1.01 false 2.49,0.917 2.979,1.302 0.49,0.385 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring.

NOTICE:

Be careful not to damage the overdrive planetary gear assembly and the plate.


HINT:

Tape the screwdriver tip before use.



b.
AT08146

Remove the retaining plate.


Hide 46.REMOVE OVERDRIVE 1-WAY CLUTCH OUTER RACE WITH OVERDRIVE 1-WAY CLUTCH

AT08147

Hide 47.REMOVE OVERDRIVE 1-WAY CLUTCH

C212484

a.

Remove the overdrive 1-way clutch from the outer race.


Hide 48.REMOVE NO. 3 OVERDRIVE PLANETARY GEAR THRUST WASHER

C212485

Hide 50.REMOVE OVERDRIVE PLANETARY RING GEAR WITH OVERDRIVE PLANETARY RING GEAR FLANGE

AT05146

a.

Remove the ring gear together with the overdrive planetary ring gear flange from the transmission case.


b.
G035541
0.563,1.438 0.385,1.667 0.385,1.667 0.604,1.667 false 2.885,1.344 2.635,1.885 2.635,1.885 2.49,1.885 false 0.698,1.563 1.042,1.792 0.344,0.229 10 false *2 2.25,1.781 2.604,1.979 0.354,0.198 10 false *1
*1 Bearing
*2 Bearing Race


Remove the bearing and bearing race from the overdrive planetary ring gear.


Hide 51.REMOVE OVERDRIVE PLANETARY RING GEAR FLANGE

a.
C237777
1.917,0.99 2.104,0.75 2.104,0.75 2.385,0.75 false 2.469,0.646 2.823,0.958 0.354,0.313 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring.

NOTICE:

Be careful not to damage the overdrive planetary ring gear and the flange.


HINT:

Tape the screwdriver tip before use.



b.
AT08134

Remove the ring gear flange from the overdrive planetary ring gear.


Hide 52.REMOVE OVERDRIVE BRAKE DISC SET

a.
C237772
1.76,1.052 1.365,0.24 1.365,0.24 1.281,0.24 true 1.094,0.156 1.365,0.365 0.271,0.208 10 false *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Tape the screwdriver tip before use.



b.

Remove the flange, 4 discs and 4 plates from the transmission case.


Hide 54.INSPECT PISTON STROKE OF SECOND COAST BRAKE

AT05216
2.885,1.083 3.094,1.74 3.094,1.74 3.198,1.74 true 2.813,1.083 2.594,1.74 2.594,1.74 2.5,1.74 true 3.229,1.646 3.427,1.813 0.198,0.167 10 false *2 2.323,1.635 2.594,1.833 0.271,0.198 10 false *1
*1 Piston Rod
*2 Mark


a.

Using a waterproof pen, place a mark on the second coast brake piston rod as shown in the illustration.


b.
AT05217
1.625,1.156 0.75,1.771 true 0.427,1.802 0.865,2.073 0.438,0.271 10 false SST

Using SST, measure the piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

SST
09240-00020  

Standard piston stroke:

1.5 to 3.0 mm (0.0591 to 0.118 in.)


If the stroke is not as specified, inspect the brake band.


Hide 55.REMOVE OVERDRIVE SUPPORT SUB-ASSEMBLY

C280868

a.

Remove the 2 bolts holding the overdrive support sub-assembly to the case.


b.
AT05249
1.76,0.594 2.396,0.844 true 2.49,0.792 2.969,1.021 0.479,0.229 10 SST

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


c.
AT05211
0.854,0.583 0.396,0.135 true 0.063,0.042 0.802,0.427 0.74,0.385 10 SST

Using SST, remove the overdrive brake assembly.

SST
09350-30020  (09350-07020)


d.
AT05110
0.635,1.25 0.635,1.448 false 2.792,1.406 2.792,1.646 false 0.573,1.51 1.083,1.906 0.51,0.396 10 false *1 2.729,1.677 3.167,1.917 0.438,0.24 10 false *2
*1 Bearing
*2 Bearing Race


Remove the bearing and bearing race from the overdrive brake.


Hide 56.REMOVE DIRECT CLUTCH ASSEMBLY WITH FORWARD CLUTCH ASSEMBLY

AT05149

a.

Remove the direct clutch together with the forward clutch from the case.


b.
AT03149
0.885,1.5 1.083,1.813 1.083,1.813 1.333,1.813 false 0.271,1.229 0.063,0.906 0.063,0.906 0.302,0.906 false 2.833,1 2.833,1.417 false 0.375,0.833 0.865,1.198 0.49,0.365 10 *1 2.781,1.479 3.177,1.719 0.396,0.24 10 *1 1.396,1.74 2.01,1.979 0.615,0.24 10 *2
*1 Bearing
*2 Bearing Race


Remove the 2 bearings and bearing race.


Hide 57.REMOVE FORWARD CLUTCH ASSEMBLY

AT05262

a.

Remove the forward clutch from the direct clutch.


b.
C238271
2.49,0.719 2.333,0.406 2.333,0.406 2.135,0.406 false 1.948,0.333 2.396,0.615 0.448,0.281 10 *1
*1 Thrust Washer


Remove the thrust washer from the forward clutch.


Hide 59.REMOVE OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
C237868
2.198,0.906 2.5,1.417 2.5,1.417 2.792,1.417 false 1.292,0.906 0.938,0.479 0.938,0.479 0.708,0.479 false 2.854,1.323 3.198,1.615 0.344,0.292 10 *1 0.375,0.396 0.927,0.656 0.552,0.26 10 SST
*1 Protective Tape


Place SST on the return spring and compress the return spring with a press.

SST
09350-30020  (09350-07030)


b.

Using a screwdriver, pry out the snap ring.

NOTICE:

Be careful not to damage the overdrive support sub-assembly and return spring.


HINT:

Tape the screwdriver tip before use.



c.

Remove the brake return spring.


Hide 61.REMOVE OVERDRIVE BRAKE PISTON

C212486

a.

Place the overdrive support onto the direct clutch assembly.


b.

Hold the overdrive brake piston so that it is not slanted and apply compressed air (392 kPa (4 kgf/cm2, 57 psi)) into the passage to remove the overdrive brake piston.


c.
D001336
1.646,1.75 0.74,0.625 0.74,0.625 1.365,0.896 true 0.552,0.542 1.156,0.885 0.604,0.344 10 *1
*1 O-Ring


Remove the 2 O-rings from the overdrive brake piston.


Hide 62.REMOVE OVERDRIVE CLUTCH DRUM OIL SEAL RING

AT08160

a.

Remove the 2 oil seal rings from the overdrive support.


b.
AT08158

Remove the clutch drum thrust washer from the overdrive support.


Hide 63.REMOVE SECOND COAST BRAKE PISTON

AT05127
2.177,0.656 1.833,1.24 false 2.271,0.563 2.969,0.885 0.698,0.323 10 SST

a.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


b.
AT05280

Apply compressed air to the oil hole to remove the second coast brake cover, piston assembly and spring.


c.

Remove the 2 O-rings from the cover.


Hide 64.REMOVE SECOND COAST BRAKE PISTON OIL SEAL RING

AT05418

Hide 65.REMOVE SECOND COAST BRAKE PISTON ROD

AT05260

a.

Firmly press the piston down to compress the compression spring.


b.

Remove the E-ring.


c.
D001299
0.635,0.854 0.635,1.198 false 2.135,1.24 2.135,1.615 false 2.344,0.198 2.49,0.198 2.49,0.198 2.76,0.854 false 1.24,0.198 1.385,0.198 1.385,0.198 1.656,0.854 false 2.073,1.677 2.719,2.052 0.646,0.375 10 false *3 0.573,1.25 0.938,1.521 0.365,0.271 10 false *1 1.01,0.125 1.542,0.313 0.531,0.188 10 false *2 2.146,0.135 2.458,0.417 0.313,0.281 10 false *4
*1 Piston Rod
*2 Washer Plate
*3 Spring
*4 Piston


Remove the piston rod, washer plate and spring from the piston.


Hide 66.REMOVE DIRECT CLUTCH DISC SET

a.
C237874
1.885,1.188 2.385,1.188 false 2.458,1.104 2.948,1.406 0.49,0.302 10 *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring from the direct clutch drum.

NOTICE:

Be careful not to damage the direct clutch drum.


HINT:

Tape the screwdriver tip before use.



b.

Remove the flange, 3 discs and 3 plates.


Hide 68.REMOVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

AT08168
1.021,0.479 1.594,0.906 true 2.052,1.094 2.677,1.49 true 0.719,0.375 1.323,0.781 0.604,0.406 10 SST 2.75,1.427 3.219,1.635 0.469,0.208 10 SST

a.

Place SST on the spring retainer and compress the return spring with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the return spring.


Hide 70.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

G037157

a.

Place the direct clutch drum on the overdrive support.


b.

Hold the direct clutch piston and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the direct clutch piston.

HINT:

Make sure the direct clutch piston is not tilted before applying compressed air.



c.
C237870
1.115,0.5 0.563,0.333 0.563,0.333 0.99,1.021 true 1.729,0.823 2.083,1.219 2.083,1.219 2.354,1.219 false 0.385,0.25 0.813,0.615 0.427,0.365 10 *1 2.427,1.146 2.917,1.448 0.49,0.302 10 *2
*1 O-Ring
*2 Protective Tape


Using a small screwdriver, remove the 2 O-rings from the piston.

NOTICE:

Be careful not to damage the direct clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 73.FIX FORWARD CLUTCH ASSEMBLY

AT08165

a.

Place the overdrive support on wooden blocks or equivalent to prevent the forward clutch shaft from touching the work stand.


b.

Place the forward clutch on the overdrive support.


Hide 74.REMOVE FORWARD CLUTCH DISC SET

a.
C237871
2.094,0.74 2.469,0.74 false 2.542,0.667 3.083,1.021 0.542,0.354 10 *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring from the input shaft.

NOTICE:

Be careful not to damage the input shaft.


HINT:

Tape the screwdriver tip before use.



b.

Remove the flange, 5 discs and 5 plates.


c.
AT08177

Remove the cushion plate.


Hide 76.REMOVE FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

D001274
1.396,0.708 0.49,0.167 true 2.323,0.896 2.813,1.25 true 0.167,0.094 0.865,0.396 0.698,0.302 10 false SST 2.865,1.188 3.344,1.385 0.479,0.198 10 false SST

a.

Place SST on the spring retainer and compress the return spring with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
D001359

Remove the return spring.


Hide 78.REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

D025661

a.

Place the input shaft onto the overdrive support.


b.

Hold the forward clutch piston by hand and apply compressed air (196 kPa (2.0 kgf/cm2, 28.5 psi)) to the overdrive support to remove the forward clutch piston.


c.
C240212
2.531,1.229 2.344,1.229 2.344,1.229 1.76,0.792 true 2.594,1.146 2.969,1.396 0.375,0.25 10 false *1
*1 Protective Tape


Remove the O-ring from the input shaft.

NOTICE:

Be careful not to damage the input shaft sub-assembly.


HINT:

Tape the screwdriver tip before use.



d.
D001361
1.156,0.167 0.958,1.385 true 1.417,0.771 1.156,0.167 1.156,0.167 1.063,0.167 false 0.854,0.083 1.083,0.271 0.229,0.188 10 false *1
*1 O-Ring
*2 Protective Tape


Remove the 2 O-rings from the forward clutch piston.

NOTICE:

Be careful not to damage the damage the forward clutch piston sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 80.REMOVE INPUT SHAFT OIL SEAL RING

AT08180

a.

Remove the 3 oil seal rings from the input shaft.


Hide 82.REMOVE SECOND COAST BRAKE BAND ASSEMBLY

a.
C237773
1.646,1.177 2.313,0.333 2.313,0.333 2.5,0.333 true 2.583,0.26 3.063,0.51 0.479,0.25 10 *1
*1 Protective Tape


Using a screwdriver, pry off the 2 E-rings from the pin and pull out the pin.

NOTICE:

Be careful not to damage the damage the transmission case.


HINT:

Tape the screwdriver tip before use.



b.
Q004030

Remove the second coast brake band from the case.


Hide 84.REMOVE FRONT PLANETARY RING GEAR SUB-ASSEMBLY

AT05128

a.

Remove the planetary ring gear from the case.


b.
C238270
2.615,0.635 2.438,0.156 2.438,0.156 2.146,0.156 false 0.802,0.979 0.542,0.479 0.542,0.479 0.385,0.479 false 0.208,0.406 0.635,0.74 0.427,0.333 10 *1 1.979,0.083 2.354,0.385 0.375,0.302 10 *2
*1 Bearing
*2 Bearing Race


Remove the bearing and bearing race from the planetary ring gear.


c.
Z005131
1.292,1.115 0.958,0.688 0.958,0.688 0.729,0.688 true 0.531,0.615 0.948,0.969 0.417,0.354 10 *1
*1 Wooden Block


Place the output shaft on wooden blocks or equivalent.


Hide 86.REMOVE FRONT PLANETARY GEAR ASSEMBLY

D029744

a.

Remove the bearing race from the planetary gear.


b.
D029740
0.625,0.354 0.396,0.115 true 0.063,0.052 0.542,0.323 0.479,0.271 10 SST

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
D029741

Remove the planetary gear from the case.


d.
C237873
1.802,1.302 1.385,0.677 1.385,0.677 1.01,0.677 true 0.823,0.594 1.281,0.875 0.458,0.281 10 *1
*1 Protective Tape


Remove the bearing and bearing race from the planetary gear.

NOTICE:

Be careful not to damage the damage the front planetary gear assembly.


HINT:

Tape the screwdriver tip before use.



Hide 88.REMOVE PLANETARY SUN GEAR SUB-ASSEMBLY WITH SUN GEAR INPUT DRUM AND NO. 1 1-WAY CLUTCH ASSEMBLY

C238269

a.

Remove the sun gear together with the sun gear input drum and 1-way clutch from the case.


Hide 90.REMOVE NO. 1 1-WAY CLUTCH ASSEMBLY

AT08188

Hide 91.REMOVE NO. 1 1-WAY CLUTCH THRUST WASHER

AT01642

Hide 92.REMOVE SUN GEAR SHAFT OIL SEAL RING

AT08189

a.

Remove the 2 oil seal rings from the sun gear input drum.


Hide 93.REMOVE SUN GEAR INPUT DRUM

C280869

a.

Place the planetary sun gear onto a wooden block or equivalent.


b.

Using snap ring pliers, remove the snap ring.


c.

Remove the input drum from the planetary sun gear.


Hide 94.REMOVE SUN GEAR INPUT DRUM SHAFT SNAP RING

a.
C237780
2.135,0.885 1.906,1.646 1.906,1.646 1.646,1.646 false 1.469,1.573 2.01,1.781 0.542,0.208 10 *1
*1 Protective Tape


Using a screwdriver, pry off the snap ring from the planetary sun gear.

NOTICE:

Be careful not to damage the damage the front planetary sun gear sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 96.REMOVE SECOND BRAKE PISTON SLEEVE

a.
C237774
1.813,1.135 0.99,0.24 0.99,0.24 0.594,0.625 true 0.917,0.031 1.313,0.344 0.396,0.313 10 *1
*1 Protective Tape


Using a screwdriver, remove the sleeve.

NOTICE:

Be careful not to damage the damage the transmission case.


HINT:

Tape the screwdriver tip before use.



Hide 97.REMOVE SECOND BRAKE DISC SET

a.
C237775
1.354,1.167 1.115,1.813 1.115,1.813 2.313,1.448 true 1,1.854 1.365,2.052 0.365,0.198 10 *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring.

NOTICE:

Be careful not to damage the damage the transmission case and sleeve.


HINT:

Tape the screwdriver tip before use.



b.

Remove the flange, 5 discs and 5 plates.


Hide 98.REMOVE OUTPUT SHAFT WITH REAR PLANETARY GEAR, NO. 2 1-WAY CLUTCH, FIRST AND REVERSE BRAKE DISC SET AND SECOND BRAKE DRUM

AT05460
2.094,0.75 2.906,1.031 true 2.969,0.979 3.354,1.219 0.385,0.24 10 false SST

a.

Using SST and a screwdriver, remove the snap ring.

SST
09350-30020  (09350-07060)


b.
AT05158

Remove the output shaft together with the rear planetary gear, No. 2 1-way clutch, first and reverse brake disc set and second brake drum from the transmission case.


c.
AT05132

Remove the bearing from the transmission case.


Hide 99.REMOVE SECOND BRAKE DRUM SUB-ASSEMBLY

Q004066

a.

Remove the second brake drum.


Hide 100.REMOVE NO. 4 PLANETARY CARRIER THRUST WASHER

AT08184

Hide 102.REMOVE SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

AT08438
0.625,1.063 0.469,0.865 0.469,0.865 0.365,0.865 true 1.125,1.469 1.417,1.75 1.417,1.75 1.604,1.75 true 0.063,0.792 0.552,1.083 0.49,0.292 10 false SST 1.677,1.667 2.323,1.896 0.646,0.229 10 false SST

a.

Place SST on the spring retainer and compress the piston return spring with a press.

SST
09350-30020  (09350-07040)

NOTICE:

Do not deform the spring seat. Stop compressing the spring when the spring seat is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.



b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the second brake piston return spring seat.


d.
AT08185

Remove the piston return spring.


Hide 103.INSPECT SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 104.REMOVE SECOND BRAKE PISTON

AT08196

a.

Hold the second brake piston by hand and apply compressed air to the second brake drum to remove the second brake piston.

HINT:

If the piston is at an angle and cannot be removed, press down on the protruding side and apply compressed air again.



b.

Remove the 2 O-rings from the piston.


Hide 105.REMOVE FIRST AND REVERSE BRAKE DISC SET

a.

Remove the flange, 6 plates and 6 discs.


Hide 107.REMOVE OUTPUT SHAFT

AT08197

Hide 108.REMOVE PLANETARY OUTPUT SHAFT OIL SEAL RING

AT08198

Hide 109.REMOVE REAR PLANETARY RING GEAR

AT08199

a.

Remove the rear planetary gear from the planetary ring gear.


b.
C212461

Remove the bearing race and bearing from the planetary ring gear.


c.
C237867
1.906,1.188 2.271,1.188 false 2.344,1.094 2.74,1.396 0.396,0.302 10 *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring.

NOTICE:

Be careful not to damage the damage the rear planetary ring gear.


HINT:

Tape the screwdriver tip before use.



d.
AT08207

Remove the planetary ring gear flange.


Hide 111.REMOVE NO. 2 1-WAY CLUTCH

AT08191

a.

Remove the 1-way clutch inner race from the planetary gear.


b.
C237866
1.813,1.24 2.115,1.24 false 2.188,1.156 2.552,1.406 0.365,0.25 10 *1
*1 Protective Tape


Using a screwdriver, pry out the snap ring.

NOTICE:

Be careful not to damage the damage the rear planetary gear.


HINT:

Tape the screwdriver tip before use.



c.
AT08193

Remove the 1-way clutch from the rear planetary gear.


d.
D028060

Remove the No. 2 planetary carrier thrust washer from the rear planetary gear.


e.
D028061

Remove the No. 1 planetary carrier thrust washer from the rear planetary gear.


Hide 113.REMOVE LEAF SPRING

AT05107

Hide 114.REMOVE BRAKE DRUM GASKET

AT04444

Hide 115.REMOVE FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

AT08336
2.052,0.635 2.344,0.406 false 1.51,0.969 1.167,0.219 1.167,0.219 1.021,0.219 true 2.396,0.333 2.99,0.625 0.594,0.292 10 SST 0.813,0.156 1.375,0.427 0.563,0.271 10 *1
*1 Snap Ring


a.

Place SST on the first and reverse brake return spring and compress the brake return spring.

SST
09350-30020  (09350-07050)


b.

Using SST, remove the snap ring and brake return spring.

SST
09350-30020  (09350-07070)


Hide 116.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

Hide 117.REMOVE NO. 2 FIRST AND REVERSE BRAKE PISTON

AT05375

a.

Hold the No. 2 first and reverse brake piston and apply compressed air to the transmission case to remove the brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.

Remove the O-ring from the brake piston.


Hide 118.REMOVE BRAKE REACTION SLEEVE

AT08335
1.99,0.354 2.094,0.146 2.094,0.146 2.313,0.146 false 2.385,0.063 3.01,0.354 0.625,0.292 10 SST

a.

Using SST, remove the sleeve.

SST
09350-30020  (09350-07080)


b.

Remove the O-rings from the sleeve.


Hide 119.REMOVE NO. 1 1ST AND REVERSE BRAKE PISTON

AT08334
1.479,0.813 1.073,0.406 false 0.75,0.313 1.365,0.521 0.615,0.208 10 SST

a.

Using SST, remove the brake piston.

SST
09350-30020  (09350-07090)


b.

Remove the 2 O-rings from the brake piston.