Home › Drivetrain › A343E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION UNIT
RM1880E _52 Drivetrain _013217 A343E AUTOMATIC TRANSMISSION / TRANSAXLE _0068515 AUTOMATIC TRANSMISSION UNIT A

A343E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

C239651
0.458,0.667 0.656,0.865 0.198,0.198 10 false A 1.292,2.708 1.552,2.948 0.26,0.24 10 false D 4,1.948 4.219,2.198 0.219,0.25 10 false B 5.604,1.594 5.802,1.792 0.198,0.198 10 false C 0.771,4.792 1.063,5.042 0.292,0.25 10 false E 2.073,4.458 2.313,4.698 0.24,0.24 10 false F 3.281,4.198 3.5,4.438 0.219,0.24 10 false G 3.781,5.896 4.042,6.094 0.26,0.198 10 false H 5.927,5.375 6.146,5.635 0.219,0.26 10 false I

Bearing Diameter:
Mark Front Race Diameter
Inside/Outside
Thrust Bearing Diameter
Inside/Outside
Rear Race Diameter
Inside/Outside
A 28.45 mm (1.12 in.)/47.1 to 47.35 mm (1.854 to 1.864 in.) 29.04 to 29.25 mm (1.144 to 1.151 in.)/50.04 to 50.34 mm (1.970 to 1.981 in.) -
B 33.0 to 33.25 mm (1.300 to 1.309 in.)/49.9 to 50.4 mm (1.97 to 1.98 in.) 31.45 to 31.70 mm (1.239 to 1.248 in.)/49.1 to 49.4 mm (1.934 to 1.944 in.) -
C 37.1 to 37.3 mm (1.461 to 1.468 in.)/58.70 to 58.95 mm (2.311 to 2.320 in.) 33.75 to 33.85 mm (1.329 to 1.332 in.)/49.8 to 50.3 mm (1.961 to 1.980 in.) -
D 36.5 to 37 mm (1.44 to 1.45 in.)/50.75 to 50.95 mm (1.999 to 2.005 in.) 33.55 to 33.80 mm (1.321 to 1.330 in.)/47.62 to 47.87 mm (1.875 to 1.884 in.) -
E 25.98 mm (1.02 in.)/48.87 mm (1.92 in.) 25.94 to 26.07 mm (1.022 to 1.026 in.)/46.62 to 46.87 mm (1.835 to 1.845 in.) 26.5 to 27.0 mm (1.043 to 1.062 in.)/47.02 mm (1.85 in.)
F - 35 to 35.3 mm (1.378 to 1.389 in.)/53.50 to 53.75 mm (2.107 to 2.116 in.) 34 to 34.5 mm (1.34 to 1.35 in.)/48.5 to 49 mm (1.91 to 1.92 in.)
G 33.55 to 33.80 mm (1.321 to 1.330 in.)/47.3 to 47.8 mm (1.87 to 1.88 in.) 35.45 to 35.61 mm (1.396 to 1.401 in.)/47.62 to 47.87 mm (1.875 to 1.884 in.) -
H 28.5 mm (1.12 in.)/44.2 mm (1.74 in.) 27.65 to 27.8 mm (1.089 to 1.094 in.)/44.2 mm (1.74 in.) -
I - 39.38 mm (1.55 in.)/57.94 to 58.24 mm (2.282 to 2.292 in.) -


Hide 2.FIX TRANSMISSION CASE

AT05393

a.

Install the transmission case to an overhaul attachment.


Hide 3.INSTALL NO. 1 FIRST AND REVERSE BRAKE PISTON

a.

Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.


b.

Coat a new O-ring with ATF and install it to the reaction sleeve.


c.
AT08209
1.865,0.542 1.958,0.177 1.958,0.177 2.063,0.177 false 1.438,1.552 1.365,1.833 1.365,1.833 1.26,1.833 false 2.115,0.094 2.427,0.302 0.313,0.208 10 false *1 1.073,1.74 1.385,1.938 0.313,0.198 10 false *2
*1 No. 1 First and Reverse Brake Piston
*2 Reaction Sleeve


Install the No. 1 brake piston to the reaction sleeve.


d.
D001243
1.323,1.531 1.156,0.635 1.156,0.635 1.323,0.635 true 2.844,1.25 3.01,0.24 3.01,0.24 2.833,0.24 false 2.656,0.146 2.927,0.344 0.271,0.198 10 false *2 1.375,0.542 1.625,0.781 0.25,0.24 10 false *1
*1 No. 1 First and Reverse Brake Piston
*2 Reaction Sleeve


With the No. 1 brake piston on the bottom (the rear side), install the brake reaction sleeve and No. 1 brake piston to the transmission case.

NOTICE:

Be careful not to damage the O-rings.



Hide 4.INSTALL NO. 2 FIRST AND REVERSE BRAKE PISTON

a.

Coat a new O-ring with ATF and install it to the brake piston.


b.
AT08333
2.969,0.646 2.5,0.146 2.5,0.146 2.396,0.146 false 2.198,0.063 2.531,0.281 0.333,0.219 10 false *1
*1 No. 2 First and Reverse Brake Piston


With the spring seat of the piston facing upward (the front side), install the piston to the transmission case.

NOTICE:

Be careful not to damage the O-ring.



Hide 5.INSTALL FIRST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
AT05429

Install the return spring to the brake piston.


b.
AT08303
2.26,0.677 2.573,0.24 false 0.531,1.313 0.531,1.719 true 1.719,1 1.365,0.24 1.365,0.24 1.219,0.24 true 1.021,0.146 1.271,0.385 0.25,0.24 10 false *1 2.625,0.125 3.01,0.323 0.385,0.198 10 false SST 0.448,1.75 0.708,1.938 0.26,0.188 10 false *2
*1 Snap Ring
*2 Return Spring Claw


Place SST on the brake return spring and compress the brake return spring.

SST
09350-30020  (09350-07050)


c.

Using SST, install the snap ring. Make sure the end gap of the snap ring is not aligned with a return spring claw.

SST
09350-30020  (09350-07070)


Hide 6.INSPECT PISTON OPERATION OF FIRST AND REVERSE BRAKE

AT05258

a.

Make sure the first and reverse brake pistons move smoothly when compressed air is applied into the transmission case.


Hide 7.INSTALL LEAF SPRING

AT05107

Hide 8.INSTALL NO. 2 1-WAY CLUTCH

a.

Coat the No. 2 planetary carrier thrust washer with petroleum jelly.


b.
D028060

Install the No. 2 planetary carrier thrust washer to the rear planetary gear.

HINT:

Make sure that the tabs of the washer fit into the cutout portions of the rear planetary gear.



c.
C280870
0.875,0.552 0.521,0.156 0.521,0.156 0.344,0.156 true 0.885,1 0.885,1.469 true 0.156,0.083 0.469,0.24 0.313,0.156 10 *1 0.823,1.5 1.135,1.656 0.313,0.156 10 *2
*1 Open End
*2 Guide


Install the 1-way clutch to the rear planetary gear.

HINT:

Make sure that the open ends of the guides of the 1-way clutch are facing upward.



d.
C237866
1.813,1.24 2.115,1.24 false 2.188,1.156 2.552,1.406 0.365,0.25 10 *1
*1 Protective tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the rear planetary gear.


HINT:

Tape the screwdriver tip before use.



e.
AT08191

While turning the 1-way clutch inner race counterclockwise, install the 1-way clutch inner race to the planetary gear.


Hide 10.INSTALL REAR PLANETARY GEAR ASSEMBLY

a.

Install the ring gear flange to the rear planetary ring gear.


b.
C237867
1.906,1.188 2.271,1.188 false 2.344,1.094 2.74,1.396 0.396,0.302 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the rear planetary ring gear.


HINT:

Tape the screwdriver tip before use.



c.
C212475
1.125,0.365 0.875,0.365 false 1.125,0.583 0.875,0.583 false 0.667,0.521 1.01,0.802 0.344,0.281 10 *1 0.667,0.281 0.969,0.552 0.302,0.271 10 *2
*1 Bearing H
*2 Bearing Race H


Coat the bearing and bearing race with petroleum jelly and install them to the rear planetary ring gear.

Bearing and Bearing Race Diameter:
Item Inside Outside
Bearing H 27.65 to 27.8 mm (1.089 to 1.094 in.) 44.2 mm (1.74 in.)
Bearing Race H 28.5 mm (1.12 in.) 44.2 mm (1.74 in.)



d.

Coat the No. 1 planetary carrier thrust washer with petroleum jelly.


e.
D028061

Install the No. 1 planetary carrier thrust washer to the planetary gear.

HINT:

Make sure that the tabs of the washer fit into the cutout portions of the planetary gear.



f.
AT08199

Install the rear planetary gear to the rear planetary ring gear.


Hide 11.INSTALL PLANETARY OUTPUT SHAFT OIL SEAL RING

a.
AT08198

Coat a new oil seal ring with ATF and install it to the output shaft.

HINT:

After installing the oil seal ring, check that it rotates smoothly.


NOTICE:

Do not expand the ring excessively.



Hide 12.INSTALL OUTPUT SHAFT

a.
AT08197

Install the output shaft to the rear planetary gear flange.


Hide 13.INSTALL SECOND BRAKE PISTON

AT08452

a.

Coat 2 new O-rings with ATF and install them to the second brake piston.


b.

Being careful not to damage the O-rings, press the second brake piston toward the second brake drum with both hands.


Hide 14.INSTALL SECOND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
AT08185

Install the piston return spring.


b.

Install the second brake piston return spring seat.


c.
AT08438
0.635,1.052 0.479,0.854 0.479,0.854 0.375,0.854 false 0.073,0.771 0.479,0.969 0.406,0.198 10 false SST

Place SST on the spring seat and compress the return spring with a press.

SST
09350-30020  (09350-07040)

NOTICE:

Do not deform the spring seat. Stop compressing the spring when the spring seat is lowered to a position 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove.



d.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


Hide 16.INSTALL NO. 4 PLANETARY CARRIER THRUST WASHER

a.
AT08184

Coat the thrust washer with petroleum jelly and install it.

HINT:

Make sure that the cutout portions of the thrust washer fit onto the teeth of the spring seat.



Hide 17.INSTALL FIRST AND REVERSE BRAKE DISC SET

C212477
2.781,1.656 3.083,1.656 false 2.76,1.49 2.917,1.49 2.917,1.49 2.917,0.427 false 1.906,1.542 1.75,1.542 1.75,1.542 1.75,0.479 false 1.75,1.323 1.906,1.323 false 1.75,1.115 1.906,1.115 false 1.75,0.906 1.906,0.906 false 1.75,0.688 1.906,0.688 false 1.604,0.479 1.906,0.479 false 2.76,1.281 2.917,1.281 false 2.76,1.063 2.917,1.063 false 2.76,0.854 2.917,0.854 false 2.76,0.635 2.917,0.635 false 2.76,0.427 3.063,0.427 false 3.156,1.563 3.396,1.76 0.24,0.198 10 *1 1.406,0.406 1.698,0.646 0.292,0.24 10 *2 3.146,0.333 3.417,0.542 0.271,0.208 10 *3
*1 Flange
*2 Disc
*3 Plate


a.

Install the flange with the rounded edge facing upward.


b.

Install the 6 discs and 6 plates.

Install in order:

*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3



Hide 18.INSTALL OUTPUT SHAFT WITH REAR PLANETARY GEAR, NO. 2 1-WAY CLUTCH, FIRST AND REVERSE BRAKE DISC SET AND SECOND BRAKE DRUM

C212487

a.

Coat the bearing with petroleum jelly and install it to the case.

Bearing Diameter:
Item Inside Outside
Bearing I 39.38 mm (1.55 in.) 57.94 to 58.24 mm (2.282 to 2.292 in.)


NOTICE:

Make sure the bearing is installed facing the proper direction.



b.
AT07893

Align the teeth on the flange, discs and plates.


c.
Q004066

Install the second brake drum to the planetary gear with the snap ring facing upwards.

NOTICE:

Make sure the oil hole in the drum faces towards the lower side of the transmission case (the side where the valve body is installed).



d.
Q004068
2.625,0.354 2.26,0.833 true 2.677,0.24 2.969,0.5 0.292,0.26 10 B 1.167,1.594 1.573,1.844 0.406,0.25 10 A

Align the teeth of the planetary gear assembly, indicated by A in the illustration, with the splines of the transmission case, indicated by B in the illustration.


e.

Install the assembled planetary gear.


f.
Z005131
1.292,1.115 0.958,0.688 0.958,0.688 0.729,0.688 true 0.531,0.615 0.948,0.969 0.417,0.354 10 *1
*1 Wooden Block


Place the output shaft on wooden blocks.


g.
AT05396
1.302,0.802 0.552,0.417 true 0.24,0.323 0.927,0.656 0.688,0.333 10 SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 19.SELECT FIRST AND REVERSE BRAKE FLANGE

AT08223

a.

Using a feeler gauge, measure the clearance between the plate and second brake drum.

Standard clearance:

0.70 to 1.22 mm (0.0276 to 0.0480 in.)


If the clearance is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
55 3.94 to 4.06 mm (0.156 to 0.159 in.)
54 4.14 to 4.26 mm (0.163 to 0.167 in.)
53 4.34 to 4.46 mm (0.171 to 0.175 in.)
52 4.54 to 4.66 mm (0.179 to 0.183 in.)
51 4.74 to 4.86 mm (0.187 to 0.191 in.)
50 4.92 to 5.08 mm (0.194 to 0.199 in.)
66 5.10 to 5.30 mm (0.201 to 0.208 in.)
67 5.30 to 5.50 mm (0.209 to 0.216 in.)



Hide 20.INSTALL SECOND BRAKE PISTON SLEEVE

AT05397

Hide 21.INSTALL BRAKE DRUM GASKET

AT04469

a.

Coat a new gasket with ATF and install it.


Hide 22.INSTALL NO. 1 1-WAY CLUTCH ASSEMBLY

a.
Z005133

Install the 1-way clutch as shown in the illustration.


Hide 23.INSTALL SECOND BRAKE DISC SET

a.
AT05398
0.198,0.75 0.104,0.75 false 0.198,1.031 0.104,1.031 false 0.198,1.323 0.104,1.323 false 0.198,1.594 0.104,1.594 false 1.042,0.146 0.823,0.219 false 0.854,1.677 0.969,1.677 false 0.833,1.396 0.948,1.396 false 0.833,1.125 0.948,1.125 false 0.833,0.844 1.021,0.844 false 0.833,0.573 0.948,0.573 false 0.198,0.469 0.104,0.469 0.104,0.469 0.104,1.719 false 0.948,0.573 0.948,1.396 false 0.042,1.781 0.688,2.115 0.646,0.333 10 *2 1.094,0.052 1.667,0.323 0.573,0.271 10 *4 1.021,1.615 1.271,1.823 0.25,0.208 10 *1 1.063,0.771 1.302,0.99 0.24,0.219 10 *3
*1 Plate (A)
*2 Disc
*3 Plate (B)
*4 Flange


Install the plate (A) with the rounded edge of the plate facing the discs.

Plate Thickness:
Item Specified Condition
Plate (A) 1.8 mm (0.0709 in.)
Plate (B) 2.5 mm (0.0984 in.)



b.

Install the 5 discs, 5 plates and flange.

Install in order:

*1 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *3 - *2 - *4



c.
C237776
1.229,1.448 0.49,1.448 true 0.281,1.365 0.844,1.667 0.563,0.302 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Tape the screwdriver tip before use.



Hide 24.INSPECT SECOND BRAKE

AT05215

a.

Using a feeler gauge, measure the clearance between the snap ring and flange.

Standard clearance:

0.62 to 1.98 mm (0.0245 to 0.0779 in.)


If the clearance is not as specified, inspect the discs.


Hide 25.INSTALL SUN GEAR INPUT DRUM SHAFT SNAP RING

a.
C237780
2.135,0.885 1.906,1.646 1.906,1.646 1.646,1.646 false 1.469,1.573 2.01,1.781 0.542,0.208 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring to the planetary sun gear.

NOTICE:

Be careful not to damage the front planetary sun gear sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 26.INSTALL SUN GEAR INPUT DRUM

AT08181

a.

Place the planetary sun gear onto a wooden block or similar object.


b.

Install the input drum to the planetary sun gear.


c.
AT07897

Using snap ring pliers, install the snap ring.


Hide 27.INSTALL SUN GEAR SHAFT OIL SEAL RING

a.

Coat 2 new oil seal rings with ATF.


b.
AT08189

Install the 2 oil seal rings to the planetary sun gear.

NOTICE:

Do not expand the rings excessively.


HINT:

After installing the oil seal rings, check that they rotate smoothly.



Hide 28.INSTALL NO. 1 1-WAY CLUTCH THRUST WASHER

HINT:

Make sure that the tabs of the washer fit into the holes in the sun gear input drum.


AT01642

Hide 29.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY WITH SUN GEAR INPUT DRUM

Q000840

a.

While turning the sun gear clockwise, install it to the 1-way clutch.

HINT:

Confirm that the thrust washer is installed correctly.



Hide 30.INSTALL FRONT PLANETARY GEAR ASSEMBLY

D029745
0.656,0.875 0.365,0.875 false 0.656,0.417 0.365,0.417 false 0.146,0.323 0.573,0.594 0.427,0.271 10 *2 0.146,0.802 0.521,1.042 0.375,0.24 10 *1
*1 Bearing Race G
*2 Bearing G


a.

Coat the bearing and bearing race with petroleum jelly and install them to the planetary gear.

Bearing and Bearing Race Diameter:
Item Inside Outside
Bearing Race G 33.55 to 33.80 mm (1.321 to 1.330 in.) 47.3 to 47.8 mm (1.87 to 1.88 in.)
Bearing G 35.45 to 35.61 mm (1.396 to 1.401 in.) 47.62 to 47.87 mm (1.875 to 1.884 in.)


NOTICE:

Make sure the bearing and race are installed facing the proper directions.



b.
D029741

Install the planetary gear to the sun gear input drum.


c.
D029740
0.625,0.354 0.396,0.115 true 0.063,0.052 0.542,0.323 0.479,0.271 10 SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)


d.

Remove the wooden blocks from under the output shaft.


e.
C220548

Coat the bearing race with petroleum jelly and install it to the planetary gear.

Bearing Race Diameter:
Item Inside Outside
Bearing Race F 34 to 34.5 mm (1.34 to 1.35 in.) 48.5 to 49 mm (1.91 to 1.92 in.)


NOTICE:

Make sure the bearing race is installed facing the proper direction.



Hide 31.INSTALL SECOND COAST BRAKE BAND ASSEMBLY

a.
Q004030

Install the brake band to the case.


b.
Q000788

Install the pin to the brake band as shown in the illustration.


c.

Install the E-ring to the pin.


Hide 32.INSTALL INPUT SHAFT OIL SEAL RING

D025664

a.

Coat the 3 new oil seal rings with ATF.


b.

Squeeze the ends of the 3 oil seal rings together, and then install them to the input shaft groove.

NOTICE:

Do not squeeze the rings excessively.


HINT:

After installing the oil seal rings, check that they rotate smoothly.



Hide 33.INSTALL FORWARD CLUTCH PISTON SUB-ASSEMBLY

a.
D001365
0.438,1.74 0.552,1.74 0.552,1.74 0.833,1.188 true 1.063,0.323 1.156,0.135 1.156,0.135 1.354,0.135 true 1.406,0.073 1.99,0.365 0.583,0.292 10 *1 0.26,1.667 0.802,1.938 0.542,0.271 10 *1
*1 O-Ring


Coat 2 new O-rings with ATF and install them to the forward clutch piston.


b.

Coat a new O-ring with ATF and install it to the input shaft.


c.
D001366

Press the clutch piston into the input shaft with both hands to install it.

NOTICE:

Be careful not to damage the O-ring.



Hide 34.INSTALL FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
D025660

Install the piston return spring.


b.
D025659
1.365,0.698 0.458,0.302 true 2.302,0.854 2.708,1.104 true 0.104,0.219 0.74,0.552 0.635,0.333 10 SST 2.792,1.052 3.229,1.406 0.438,0.354 10 SST

Place SST on the return spring, compress the return spring with a press, and then install the snap ring.

SST
09350-30020  (09350-07040, 09350-07070)

NOTICE:

Make sure the end gap of the snap ring is not aligned with the return spring claw.



Hide 35.INSTALL FORWARD CLUTCH DISC SET

AT08177

a.

Install the cushion plate.


b.
C239658
2.688,0.271 2.688,0.125 2.688,0.125 2.958,0.125 false 3.125,1.573 3.125,0.5 3.125,0.5 2.74,0.5 false 2.729,0.729 3.115,0.729 false 2.719,0.948 3.115,0.948 false 2.719,1.135 3.115,1.135 false 2.729,1.333 3.125,1.333 false 1.854,1.594 1.854,0.625 1.854,0.625 2.188,0.625 false 2.188,0.854 1.854,0.854 false 2.188,1.042 1.854,1.042 false 2.188,1.26 1.854,1.26 false 2.188,1.448 1.854,1.448 false 3.021,0.052 3.271,0.281 0.25,0.229 10 *3 3.052,1.604 3.323,1.823 0.271,0.219 10 *2 1.781,1.625 2.385,1.99 0.604,0.365 10 *1
*1 Plate
*2 Disc
*3 Flange


Install the 5 plates, 5 discs and flange.

Install in order:

*1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *1 - *2 - *3



c.
C237871
2.094,0.74 2.469,0.74 false 2.542,0.667 3.083,1.021 0.542,0.354 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:
·

Make sure the end gap of the snap ring is not aligned with the cutout portion of the input shaft sub-assembly.

·

Be careful not to damage the input shaft sub-assembly.



HINT:

Tape the screwdriver tip before use.



Hide 36.SELECT FORWARD CLUTCH FLANGE

C280871
2.521,0.417 2.177,0.188 2.177,0.188 1.938,0.188 true 1.625,0.115 2.083,0.313 0.458,0.198 10 SST 3.156,0.083 3.427,0.313 0.271,0.229 10 (A)

a.

Using SST and a dial indicator, measure the piston stroke (A) of the clutch flange at both ends across the diameter while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi))

SST
09350-30020  (09350-06120)

Standard piston stroke (A):

0.60 to 1.00 mm (0.0237 to 0.0394 in.)


If the piston stroke (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
90 2.95 to 3.05 mm (0.117 to 0.120 in.)
91 3.15 to 3.25 mm (0.125 to 0.127 in.)
92 3.35 to 3.45 mm (0.132 to 0.135 in.)
93 3.55 to 3.65 mm (0.140 to 0.143 in.)
94 3.75 to 3.85 mm (0.148 to 0.151 in.)
95 3.95 to 4.05 mm (0.156 to 0.159 in.)
96 4.15 to 4.25 mm (0.164 to 0.167 in.)
97 4.35 to 4.45 mm (0.172 to 0.175 in.)



Hide 37.INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.
D001453
0.969,1.01 0.552,1.396 true 1.76,0.979 2.458,1.531 true 0.365,1.354 0.823,1.635 0.458,0.281 10 *1 2.531,1.51 2.813,1.719 0.281,0.208 10 *1
*1 O-Ring


Coat 2 new O-rings with ATF and install them to the direct clutch piston.


b.
D001354

Press the clutch piston into the clutch drum with both hands to install it.

NOTICE:

Be careful not to damage the O-rings.



Hide 38.INSTALL DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
D001349

Install the direct clutch return spring.


b.
D001348
1.396,1.042 0.563,0.479 true 2.094,0.927 2.594,1.469 true 2.5,1.51 2.979,1.792 0.479,0.281 10 SST 0.219,0.385 1.104,0.729 0.885,0.344 10 SST

Place SST on the return spring and compress the return spring with a press.

SST
09350-30020  (09350-07040)


c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Be sure the end gap of the snap ring is not aligned with the return spring claw.



Hide 39.INSTALL DIRECT CLUTCH DISC SET

a.
C212472
1.854,1.656 1.708,1.656 false 2.99,1.5 2.719,1.5 false 2.865,1.198 2.719,1.198 false 2.719,0.865 2.865,0.865 2.865,0.865 2.865,1.5 false 2.979,0.375 2.729,0.375 false 1.854,1.344 1.771,1.344 false 1.854,1.031 1.771,1.031 1.771,1.031 1.771,1.656 false 1.51,1.552 1.708,1.74 0.198,0.188 10 true *1 3.031,1.396 3.26,1.625 0.229,0.229 10 false *2 3.021,0.271 3.302,0.5 0.281,0.229 10 false *3
*1 Plate
*2 Disc
*3 Flange


Install the 3 plates and 3 discs.


b.

Install the flange with the flat end facing downward.

Install in order:

*1 - *2 - *1 - *2 - *1 - *2 - *3



c.
C237874
1.885,1.188 2.385,1.188 false 2.458,1.104 2.948,1.406 0.49,0.302 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:
·

Make sure the end gap of the snap ring is not aligned with the cutout portion of the direct clutch drum.

·

Be careful not to damage the direct clutch drum.



HINT:

Tape the screwdriver tip before use.



Hide 40.SELECT DIRECT CLUTCH FLANGE

a.
AT08250

Place the direct clutch onto the overdrive support.


b.
C280872
0.75,1.083 0.552,0.802 0.552,0.802 0.76,0.802 true 0.802,0.729 1.26,0.927 0.458,0.198 10 SST 0.146,0.792 0.604,0.99 0.458,0.198 10 (A)

Using SST and a dial indicator, measure the piston stroke (A) of the clutch flange at both ends across the diameter while applying and releasing compressed air (186 to 206 kPa (1.9 to 2.1 kgf/cm2, 27 to 30 psi)).

SST
09350-30020  (09350-06120)

Standard piston stroke (A):

0.40 to 0.70 mm (0.0158 to 0.0275 in.)


If the piston stroke (A) is not as specified, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
53 3.25 to 3.35 mm (0.128 to 0.131 in.)
54 3.35 to 3.45 mm (0.132 to 0.135 in.)
55 3.45 to 3.55 mm (0.136 to 0.139 in.)
56 3.55 to 3.65 mm (0.140 to 0.143 in.)
57 3.65 to 3.75 mm (0.144 to 0.147 in.)
58 3.75 to 3.85 mm (0.148 to 0.151 in.)



Hide 41.INSTALL DIRECT CLUTCH ASSEMBLY

a.
C238271
2.479,0.719 2.323,0.406 2.323,0.406 2.115,0.406 false 1.917,0.333 2.208,0.615 0.292,0.281 10 false *1
*1 Thrust Washer


Install the thrust washer to the input shaft.


b.
AT05262

Install the direct clutch to the input shaft.


Hide 42.INSTALL FRONT PLANETARY RING GEAR SUB-ASSEMBLY

Z005137
1.167,1.656 1.292,1.917 1.292,1.917 1.385,1.917 false 0.531,1.792 0.656,2.063 0.656,2.063 0.75,2.063 false 1.438,1.844 1.948,2.021 0.51,0.177 10 *1 0.833,1.99 1.219,2.146 0.385,0.156 10 *2
*1 Bearing Race E
*2 Bearing E


a.

Coat the bearing race and bearing with petroleum jelly and install them to the input shaft.

Bearing and Bearing Race Diameter:
Item Inside Outside
Bearing Race E 25.98 mm (1.02 in.) 48.87 mm (1.92 in.)
Bearing E 25.94 to 26.07 mm (1.022 to 1.026 in.) 46.62 to 46.87 mm (1.835 to 1.845 in.)


NOTICE:

Make sure the bearing and race are installed facing the proper directions.



b.
Z005136

Coat the bearing race with petroleum jelly and install it to the front planetary ring gear.

Bearing Race Diameter:
Item Inside Outside
Bearing Race E 26.5 to 27.0 mm (1.044 to 1.062 in.) 47.02 mm (1.85 in.)


NOTICE:

Make sure the bearing race is installed facing the proper direction.



c.
AT05432

Align the teeth of the discs in the forward clutch.


d.
Q000838

Align the splines of the planetary ring gear with the teeth of the discs and install the planetary ring gear to the forward clutch.


Hide 43.INSTALL DIRECT CLUTCH ASSEMBLY WITH FORWARD CLUTCH ASSEMBLY

C280873
1.052,1.677 0.792,1.677 false 0.594,1.604 0.906,1.76 0.313,0.156 10 *1
*1 Bearing F


a.

Coat the bearing with petroleum jelly and install it to the ring gear.

Bearing Diameter:
Item Inside Outside
Bearing F 35 to 35.3 mm (1.378 to 1.389 in.) 53.50 to 53.75 mm (2.107 to 2.116 in.)


NOTICE:

Make sure the bearing is installed facing the proper direction.



b.
AT08234

Install the assembled direct clutch, forward clutch and front planetary ring gear to the transmission case.


c.
AT05213

Using a vernier caliper, measure the distance between the sun gear input drum and direct clutch drum as shown in the illustration.

Standard distance:

5.3 to 7.3 mm (0.209 to 0.287 in.)


If the distance is not as specified, check for improper installation.


d.
Z005236

Coat the bearing with petroleum jelly and install it to the forward clutch.

Bearing Diameter:
Item Inside Outside
Bearing D 33.55 to 33.80 mm (1.321 to 1.330 in.) 47.62 to 47.87 mm (1.875 to 1.884 in.)


NOTICE:

Make sure the bearing is installed facing the proper direction.



Hide 44.INSTALL SECOND COAST BRAKE PISTON ROD

a.
D001299
0.635,0.854 0.635,1.198 false 2.135,1.24 2.135,1.615 false 2.344,0.198 2.49,0.198 2.49,0.198 2.76,0.854 false 1.24,0.198 1.385,0.198 1.385,0.198 1.656,0.854 false 2.073,1.677 2.719,2.052 0.646,0.375 10 false *3 0.573,1.25 0.938,1.521 0.365,0.271 10 false *1 1.052,0.125 1.583,0.313 0.531,0.188 10 false *2 2.156,0.125 2.469,0.406 0.313,0.281 10 false *4
*1 Piston Rod
*2 Washer Plate
*3 Compression Spring
*4 Piston


Install the washer plate, compression spring and piston to the piston rod.


b.

Firmly press the piston down to compress the compression spring.


c.
AT05260

Install the E-ring.


Hide 45.INSTALL SECOND COAST BRAKE PISTON OIL SEAL RING

G037154

a.

Coat a new oil seal ring with ATF.


b.

Spread the ends of the ring to install the oil seal ring to the piston groove. Then squeeze its ends together.

NOTICE:

Do not spread the ring ends excessively.



Hide 46.INSTALL SECOND COAST BRAKE PISTON ASSEMBLY

AT05086

a.

Coat 2 new O-rings with ATF and install them to the second coast brake cover.


b.

Install a new spring, piston assembly and cover to the case.


c.
AT05127
2.177,0.656 1.833,1.24 false 2.271,0.563 2.969,0.885 0.698,0.323 10 SST

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)


Hide 47.INSPECT PISTON STROKE OF SECOND COAST BRAKE

AT05216
2.813,1.073 2.49,1.729 2.49,1.729 2.333,1.729 true 2.875,1.073 2.875,1.719 true 2.823,1.792 3.229,2.031 0.406,0.24 10 *2 2.167,1.667 2.469,1.896 0.302,0.229 10 *1
*1 Piston Rod
*2 Mark


a.

Using a waterproof pen, place a mark on the second coast brake piston rod as shown in the illustration.


b.
AT05217
1.625,1.156 0.75,1.771 true 0.594,1.823 1.333,2.042 0.74,0.219 10 SST

Using SST, measure the piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

SST
09240-00020  

Standard piston stroke:

1.5 to 3.0 mm (0.0591 to 0.118 in.)


If the piston stroke is not as specified, inspect the brake band.

If the piston stroke is still not as specified, select a piston rod of an appropriate length from the table below so that the measured value is within the standard range.

Piston Rod Length:
Groove Mark Length
Without 78.3 to 78.5 mm (3.083 to 3.090 in.)
With 79.8 to 80.0 mm (3.142 to 3.149 in.)



Hide 48.INSTALL OVERDRIVE BRAKE PISTON

a.
D001336
1.646,1.75 0.74,0.625 0.74,0.625 1.365,0.896 true 0.552,0.542 1.156,0.885 0.604,0.344 10 *1
*1 O-Ring


Coat 2 new O-rings with ATF and install them to the overdrive brake piston.


b.
AT01979

Press the brake piston into the overdrive support with both hands to install it.

NOTICE:

Be careful not to damage the O-rings.



Hide 49.INSTALL OVERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY

a.
AT01978

Install the return spring to the brake piston.


b.

Place SST on the return spring and compress the return spring with a press.

SST
09350-30020  (09350-07030)


c.
D001341
1.219,1.208 0.906,0.646 0.906,0.646 0.75,0.646 true 1.969,0.948 2,0.927 false 1.948,0.99 1.344,0.323 1.344,0.323 1.146,0.323 true 1.969,0.99 2,0.969 false 1.969,1.031 2,1.01 false 1.969,1.073 2,1.052 false 1.969,1.115 2,1.094 false 1.969,0.917 2,0.896 false 0.406,0.594 0.958,0.854 0.552,0.26 10 SST 0.948,0.25 1.219,0.49 0.271,0.24 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:
·
C280874
1.458,0.802 1.615,1 0.156,0.198 10 A 1.24,4.281 1.396,4.479 0.156,0.198 10 B

Make sure the end gap of the snap ring is not aligned with the cutout portion of the overdrive support.

·

Be careful not to damage the overdrive support sub-assembly and return spring.



HINT:
·

After assembling the overdrive support assembly completely, align the position of the piston with A in the illustration.

·

Align the end gap of the snap ring with B in the illustration.

·

Make sure that the snap ring is not on top of the part of the return spring that prevents the snap ring from coming off. Check this in all 8 locations.

·

Tape the screwdriver tip before use.




Hide 51.INSTALL OVERDRIVE CLUTCH DRUM OIL SEAL RING

AT08151

a.

Coat 2 new oil seal rings with ATF.


b.

Squeeze the ends of the 2 oil seal rings together, and then install them to the stator shaft groove.

NOTICE:

Do not squeeze the rings excessively.


HINT:

After installing the oil seal rings, check that they rotate smoothly.



Hide 52.INSTALL OVERDRIVE BRAKE ASSEMBLY

AT05110
0.635,1.25 0.635,1.448 false 2.792,1.396 2.792,1.635 false 0.573,1.51 1.083,1.906 0.51,0.396 10 *1 2.729,1.677 3.167,1.917 0.438,0.24 10 *2
*1 Bearing C
*2 Bearing Race D


a.

Coat the bearing and bearing race with petroleum jelly and install them to the overdrive brake assembly.

Bearing and Bearing Race Diameter:
Item Inside Outside
Bearing C 33.75 to 33.85 mm (1.329 to 1.332 in.) 49.8 to 50.3 mm (1.961 to 1.980 in.)
Bearing Race D 36.5 to 37 mm (1.44 to 1.45 in.) 50.75 to 50.95 mm (1.999 to 2.005 in.)


NOTICE:

Make sure the bearing and race are installed facing the proper directions.



b.
AT08158

Coat the thrust washer with petroleum jelly and install it to the overdrive support.

HINT:

Make sure that the tab of the washer fits into the groove of the overdrive support.



c.
AT05400
1.24,1.083 1.406,1.76 1.406,1.76 1.688,1.094 true 1.302,1.823 1.844,2.073 0.542,0.25 10 SST

Using the 2 bolts of SST, aim the bolt and oil holes of the overdrive brake assembly toward the valve body side, and align them with the bolt holes of the transmission case. Then install the overdrive brake assembly.

SST
09350-30020  (09350-07020)


d.

Temporarily install the 2 bolts.


e.
C280875
0.938,0.781 1.365,0.781 true 1.448,0.708 1.906,0.906 0.458,0.198 10 SST 2.406,1.833 2.865,2.031 0.458,0.198 10 A

Using SST, install the snap ring.

SST
09350-30020  (09350-07060)

Standard distance A:

24 mm (0.945 in.)


HINT:

Install the snap ring with the open end facing toward the valve body.



f.
C280876

Tighten the 2 bolts.

Torque:
25 N*m (260 kgf*cm, 19 ft.*lbf)


Hide 54.INSTALL OVERDRIVE BRAKE DISC SET

C239657
1.354,0.229 1.552,0.229 false 1.354,0.656 1.573,0.656 1.573,0.656 1.573,1.646 false 0.552,1.604 0.552,0.458 0.552,0.458 0.74,0.458 false 1.365,0.969 1.573,0.969 false 1.365,1.281 1.573,1.281 false 1.365,1.573 1.573,1.573 false 0.74,0.792 0.552,0.792 false 0.74,1.083 0.552,1.083 false 0.74,1.385 0.552,1.385 false 1.604,0.146 1.885,0.375 0.281,0.229 10 false *3 0.469,1.656 0.771,1.875 0.302,0.219 10 false *2 1.479,1.688 1.781,1.875 0.302,0.188 10 false *1
*1 Plate
*2 Disc
*3 Flange


a.

Install the 4 plates, 4 discs and flange.

Install in order:

*1 - *2 -*1 - *2 - *1 - *2 - *1 - *2 - *3



b.
C237772
1.75,1.073 1.354,0.26 1.354,0.26 1.031,0.26 true 0.854,0.188 1.396,0.479 0.542,0.292 10 false *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the transmission case.


HINT:

Tape the screwdriver tip before use.



Hide 55.SELECT OVERDRIVE BRAKE FLANGE

AT05282
0.521,0.854 0.917,0.167 true 1,0.052 1.604,0.365 0.604,0.313 10 SST

a.

Place SST and a dial indicator on the overdrive brake piston.

SST
09350-30020  (09350-06120)


b.

Measure the stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi))

Standard piston stroke:

1.75 to 2.05 mm (0.0689 to 0.0807 in.)


If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.

If the piston stroke is still outside the standard range, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
33 3.25 to 3.35 mm (0.128 to 0.131 in.)
35 3.45 to 3.55 mm (0.136 to 0.139 in.)
36 3.55 to 3.65 mm (0.140 to 0.143 in.)
37 3.65 to 3.75 mm (0.144 to 0.147 in.)
38 3.75 to 3.85 mm (0.148 to 0.151 in.)
39 3.85 to 3.95 mm (0.152 to 0.155 in.)
40 3.95 to 4.05 mm (0.156 to 0.159 in.)



Hide 56.INSTALL OVERDRIVE PLANETARY RING GEAR FLANGE

a.
AT08134

Install the ring gear flange to the overdrive planetary ring gear.


b.
C237777
1.917,0.99 2.104,0.75 2.104,0.75 2.385,0.75 false 2.458,0.667 2.813,0.979 0.354,0.313 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the overdrive planetary ring gear and the flange.


HINT:

Tape the screwdriver tip before use.



Hide 57.INSTALL OVERDRIVE PLANETARY RING GEAR

a.
Q000842
2.073,0.375 2.375,0.375 false 2.396,0.271 2.604,0.469 0.208,0.198 10 *1
*1 Bearing Race C


Coat the bearing race with petroleum jelly and install it to the overdrive planetary ring gear flange.

Bearing Race Diameter:
Item Inside Outside
Bearing Race C 37.1 to 37.3 mm (1.461 to 1.468 in.) 58.70 to 58.95 mm (2.311 to 2.320 in.)


NOTICE:

Make sure the bearing race is installed facing the proper direction.



b.
AT05146

Install the ring gear.


Hide 58.INSTALL NO. 3 OVERDRIVE PLANETARY GEAR THRUST WASHER

a.
C212485

Install the thrust washer to the overdrive planetary gear with the grooves facing upward.


Hide 59.INSTALL OVERDRIVE 1-WAY CLUTCH

a.

Install the 2 retainers to the 1-way clutch.


b.
C280877
0.938,0.729 1.406,0.25 1.406,0.25 1.615,0.25 true 1.698,0.177 2.01,0.375 0.313,0.198 10 *1
*1 Flange


Install the 1-way clutch to the outer race with the flange of the 1-way clutch facing upward.


c.
C280878

Install the overdrive 1-way clutch and outer race to the overdrive planetary gear.


Hide 60.INSTALL OVERDRIVE RETAINING PLATE

a.
AT08146

Install the retaining plate.


b.
C237778
1.979,1.26 2.25,1.01 2.25,1.01 2.385,1.01 false 2.469,0.938 2.958,1.323 0.49,0.385 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the overdrive planetary gear assembly and the plate.


HINT:

Tape the screwdriver tip before use.



Hide 62.INSTALL OVERDRIVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

a.

Coat 2 new O-rings with ATF and install them to the overdrive direct clutch piston.


b.
AT08144

Press the clutch piston into the clutch drum with both hands to install it.

NOTICE:

Be careful not to damage the O-rings.



Hide 63.INSTALL OVERDRIVE DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY

a.
AT08145

Install the overdrive brake return spring to the overdrive direct clutch piston.


b.
C212482
1.167,0.469 0.865,0.25 0.865,0.25 0.719,0.25 false 2.49,0.802 2.948,0.802 true 0.354,0.167 1.115,0.5 0.76,0.333 10 false SST 3.052,0.708 3.417,0.917 0.365,0.208 10 false SST

Place SST on the return spring and compress the return spring with a press.

SST
09350-30020  (09350-07040)


c.

Using SST, install the snap ring.

SST
09350-30020  (09350-07070)

NOTICE:

Make sure the end gap of the snap ring is not aligned with the return spring claw.



Hide 64.INSTALL OVERDRIVE DIRECT CLUTCH DISC SET

AT01639
3.104,0.677 3.302,0.677 3.302,0.677 3.302,1.427 false 3.104,1.156 3.302,1.156 false 1.938,1.344 1.792,1.344 false 1.938,0.896 1.792,0.896 1.792,0.896 1.792,1.563 false 1.729,1.604 2.156,1.885 0.427,0.281 10 *1 3.229,1.458 3.427,1.656 0.198,0.198 10 *2
*1 Plate
*2 Disc


a.

Install the 2 plates and 2 discs.

Install in order:

*1 - *2 - *1 - *2



b.
AT08155

Install the flange with the flat end facing downward.


c.
C237869
2.198,0.979 1.875,0.604 1.875,0.604 1.74,0.604 false 1.563,0.531 1.792,0.813 0.229,0.281 10 *1
*1 Protective Tape


Using a screwdriver, install the snap ring.

NOTICE:

Be careful not to damage the overdrive direct clutch drum sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 65.SELECT OVERDRIVE CLUTCH FLANGE

a.
AT08140

Place the oil pump onto the torque converter clutch, and then place the overdrive direct clutch drum assembly onto the oil pump.


b.
AT04448
2.573,1.5 2.854,1.052 true 1.302,1.385 0.583,1.656 true 2.948,0.969 3.417,1.229 0.469,0.26 10 SST 0.385,1.604 0.802,1.854 0.417,0.25 10 *1
*1 Vinyl Tape


Using SST and a dial indicator, measure the overdrive direct clutch piston stroke while applying and releasing compressed air (392 kPa (4.0 kgf/cm2, 57 psi)).

SST
09350-30020  (09350-06120)

Standard piston stroke:

1.85 to 2.15 mm (0.0728 to 0.0846 in.)


If the piston stroke is not as specified, parts may have been assembled incorrectly. Check and reassemble again.

If the piston stroke is still outside the standard range, select a flange of an appropriate thickness from the table below so that the measured value is within the standard range.

Flange Thickness:
Mark Thickness
21 3.05 to 3.15 mm (0.1201 to 0.1240 in.)
20 3.15 to 3.25 mm (0.125 to 0.127 in.)
19 3.25 to 3.35 mm (0.128 to 0.131 in.)
18 3.35 to 3.45 mm (0.132 to 0.135 in.)
17 3.45 to 3.55 mm (0.136 to 0.139 in.)
16 3.55 to 3.65 mm (0.140 to 0.143 in.)



Hide 66.INSTALL OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY

a.
AT08130

Align the teeth of the discs in the direct clutch assembly.


b.

Install the direct clutch drum assembly to the overdrive planetary gear.


Hide 67.INSTALL OVERDRIVE PLANETARY GEAR ASSEMBLY WITH DIRECT CLUTCH ASSEMBLY AND OVERDRIVE 1-WAY CLUTCH ASSEMBLY

a.
C280879
1.635,0.552 1.948,0.552 true 2.021,0.469 2.333,0.625 0.313,0.156 10 *1
*1 Bearing B


Coat the bearing with petroleum jelly and install it to the ring gear.

Bearing Diameter:
Item Inside Outside
Bearing B 31.45 to 31.70 mm (1.230 to 1.248 in.) 49.1 to 49.4 mm (1.934 to 1.944 in.)


NOTICE:

Make sure the bearing is installed facing the proper direction.



b.
Z005128
0.198,1.26 0.427,0.583 0.427,0.583 0.521,0.583 false 0.594,0.5 1.031,0.823 0.438,0.323 10 *1
*1 Bearing Race B


Coat the bearing race with petroleum jelly and install it to the planetary gear.

Bearing Race Diameter:
Item Inside Outside
Bearing Race B 33.0 to 33.25 mm (1.300 to 1.309 in.) 49.9 to 50.4 mm (1.97 to 1.98 in.)


NOTICE:

Make sure the bearing race is installed facing the proper direction.



c.
Q000619

Install the overdrive planetary gear together with the overdrive direct clutch and 1-way clutch.


d.
AT04470
0.969,1.156 0.427,0.906 true 0.094,0.823 0.688,1.083 0.594,0.26 10 SST

Place SST on the transmission case.

SST
09350-36010  (09350-06090)


e.

Using a vernier caliper, measure the distance between the top of SST and the clutch drum.

Standard distance:

15.5 to 16.5 mm (0.610 to 0.650 in.)


If the distance is not as specified, check for improper installation.


f.
AT08313
1.625,0.635 1.771,0.344 1.771,0.344 2.031,0.344 true 2.115,0.271 2.708,0.583 0.594,0.313 10 *1
*1 Bearing A


Coat the bearing with petroleum jelly and install it to the overdrive direct clutch.

Bearing Diameter:
Item Inside Outside
Bearing A 29.04 to 29.25 mm (1.144 to 1.151 in.) 50.04 to 50.34 mm (1.970 to 1.981 in.)


NOTICE:

Make sure the bearing is installed facing the proper direction.



Hide 68.INSTALL OIL PUMP ASSEMBLY

Z005237
1.281,1.083 0.938,1.083 false 0.729,1.01 1.083,1.313 0.354,0.302 10 *1
*1 Bearing Race A


a.

Coat the bearing race with petroleum jelly and install it to the oil pump.

Bearing Race Diameter:
Item Inside Outside
Bearing Race A 28.45 mm (1.12 in.) 47.1 to 47.35 mm (1.854 to 1.864 in.)


NOTICE:

Make sure the bearing race is installed facing the proper direction.



b.

Coat a new O-ring with ATF and install it to the pump body.


c.

Slide the oil pump onto the input shaft, align the bolt holes of the oil pump assembly with the bolt holes of the transmission case and install the oil pump.


d.

Hold the input shaft and lightly press the oil pump body to slide the oil seal rings toward the overdrive direct clutch drum.

NOTICE:

Do not forcefully push on the oil pump as the oil seal rings will stick to the direct clutch drum.



e.
C280880

Install the 7 bolts.

Torque:
21 N*m (215 kgf*cm, 16 ft.*lbf)


Hide 69.INSPECT INPUT SHAFT ROTATION

AT05244

a.

Make sure the input shaft rotates smoothly.


Hide 70.INSPECT INDIVIDUAL PISTON OPERATION

C280977
1.448,3.448 2.781,3.448 true 1.365,2.844 2.781,2.844 true 1.833,1.583 2.75,1.583 true 2.083,1.833 2.75,1.833 true 1.25,1.531 0.823,0.5 0.823,0.5 0.573,0.5 true 1.406,1.552 1.406,0.5 1.406,0.5 1.24,0.5 true 1.656,1.542 1.656,0.5 1.656,0.5 1.823,0.5 true 2.115,1.042 2.396,0.604 2.396,0.604 2.563,0.604 true 1.927,0.417 2.24,0.573 0.313,0.156 10 false *1 1,0.417 1.313,0.573 0.313,0.156 10 false *2 0.375,0.427 0.688,0.583 0.313,0.156 10 false *3 2.844,1.49 3.156,1.646 0.313,0.156 10 false *4 2.854,1.75 3.167,1.906 0.313,0.156 10 false *5 2.885,2.76 3.198,2.917 0.313,0.156 10 false *6 2.885,3.365 3.198,3.521 0.313,0.156 10 false *7 2.646,0.531 2.958,0.688 0.313,0.156 10 false *8
*1 Overdrive Direct Clutch (C1)
*2 Direct Clutch (C2)
*3 Forward Clutch (C3)
*4 Overdrive Brake (B1)
*5 Second Coast Brake (B2)
*6 Second Brake (B3)
*7 First and Reverse Brake (B4)
*8 C-0 Accumulator Piston Hole


a.

Check the operating sound while applying compressed air to the oil hole indicated in the illustration.

HINT:

When inspecting the overdrive direct clutch, check the operating sound with the C-0 accumulator piston hole closed.

If there is no sound, disassemble and check the installation condition of the parts.



Hide 71.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

AT05238
1.594,0.615 1.594,1.792 true 1.469,1.854 2.229,2.146 0.76,0.292 10 SST

a.

Using SST and a hammer, tap in 2 new oil seals.

SST
09350-30020  (09350-07110)


b.

Coat the lips of the oil seals with MP grease.


Hide 72.INSTALL MANUAL VALVE LEVER SHAFT

Q000775
0.896,0.938 0.896,0.531 0.896,0.531 1.042,0.531 false 1.104,0.188 0.896,0.188 0.896,0.188 0.615,0.854 false 2.531,1.396 2.198,1.979 2.198,1.979 1.99,1.979 false 1.094,0.458 1.542,0.76 0.448,0.302 10 *1 1.177,0.125 1.74,0.396 0.563,0.271 10 *3 1.792,1.906 2.49,2.083 0.698,0.177 10 *2
*1 Spacer
*2 Manual Valve Lever Shaft
*3 Manual Valve Lever


a.

Install a new spacer to the manual valve lever.


b.

Pass the manual valve lever shaft through the transmission case and manual valve lever to install it.


c.
AT05405

Using a hammer, tap in a new spring pin.


d.
D006523

Align the manual valve lever indentation with the spacer hole and stake them with a punch.


e.

Check that the shaft rotates smoothly.


Hide 73.INSTALL PARKING LOCK PAWL

C280978
2,0.406 2.25,0.219 2.25,0.219 2.438,0.219 true 1.271,1.375 0.792,0.313 0.792,0.313 0.531,0.313 true 1.031,1.646 1.375,2.031 1.375,2.031 1.135,2.031 true 1.406,1.427 1.906,1.969 1.906,1.969 2.146,1.969 true 2.208,1.885 2.521,2.042 0.313,0.156 10 *1 0.333,0.24 0.646,0.396 0.313,0.156 10 *2 2.531,0.146 2.844,0.302 0.313,0.156 10 *3 0.948,1.938 1.26,2.094 0.313,0.156 10 *4
*1 E-Ring
*2 Parking Lock Pawl Shaft
*3 Parking Lock Pawl
*4 Spring


a.

Install the E-ring to the parking lock pawl shaft.


b.

Install the parking lock pawl, shaft and spring.


Hide 74.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

Z006797

a.

Connect the parking lock rod to the manual valve lever to install it.


Hide 75.INSTALL PARKING LOCK PAWL BRACKET

C280979

a.

Install the parking lock pawl bracket to the transmission case with the 3 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


b.
Z005222
1.063,0.594 0.708,1.083 true 3.021,0.542 2.854,0.542 2.854,0.542 2.635,1.146 true 2.458,1.906 2.615,1.906 2.615,1.906 2.781,1.427 true 3.104,0.479 3.375,0.719 0.271,0.24 10 *2 0.594,1.115 1.115,1.385 0.521,0.271 10 *1 2.271,1.833 2.615,2.021 0.344,0.188 10 *3
*1 Manual Valve Lever
*2 Planetary Ring Gear
*3 Parking Lock Pawl


Shift the manual valve lever to the P position and confirm that the planetary ring gear is correctly locked by the parking lock pawl.


Hide 76.INSTALL C-0 ACCUMULATOR PISTON

a.

Coat a new O-ring with ATF and install it to the piston.


b.
C280980

Install the 2 springs and accumulator piston to the hole.

Accumulator Spring Diameter:
Item Free Length
Outer Diameter
Color
C-0 Inner Spring 46.0 mm (1.81 in.)
14.02 mm (0.552 in.)
Yellow
C-0 Outer Spring 74.6 mm (2.94 in.)
20.9 mm (0.823 in.)
Orange



Hide 77.INSTALL B-0 ACCUMULATOR PISTON

C280981

a.

Coat 2 new O-rings with ATF and install them to the piston.


b.

Install the spring and accumulator piston to the hole.

Accumulator Spring Diameter:
Item Free Length
Outer Diameter
Color
B-0 Spring 62.0 mm (2.44 in.)
16.0 mm (0.630 in.)
Green



Hide 78.INSTALL C-2 ACCUMULATOR PISTON

C280982

a.

Coat 2 new O-rings with ATF and install them to the piston.


b.

Install the 2 springs and accumulator piston to the hole.

Accumulator Spring Diameter:
Item Free Length
Outer Diameter
Color
C-2 Inner Spring 42.06 mm (1.66 in.)
14.7 mm (0.579 in.)
Pink
C-2 Outer Spring 68.53 mm (2.70 in.)
20.2 mm (0.795 in.)
Blue



Hide 79.INSTALL B-2 ACCUMULATOR PISTON

C280983

a.

Coat 2 new O-rings with ATF and install them to the piston.


b.

Install the spring and accumulator piston to the hole.

Accumulator Spring Diameter:
Item Free Length
Outer Diameter
Color
B-2 Spring 70.50 mm (2.78 in.)
19.9 mm (0.783 in.)
Light Green



Hide 80.INSTALL CHECK BALL BODY

AT05098
1.635,0.396 1.979,0.396 false 1.594,0.885 1.979,0.885 false 2.042,0.323 2.635,0.76 0.594,0.438 10 *2 2.052,0.792 2.656,1.146 0.604,0.354 10 *1
*1 Spring
*2 Check Ball Body


a.

Install the spring and check ball body.


Hide 81.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

AT08393
1.219,1.167 0.802,0.49 0.802,0.49 0.573,0.49 true 0.865,1.385 0.708,1.792 0.708,1.792 0.531,1.792 true 1.042,1.292 1.323,1.76 1.323,1.76 1.438,1.76 true 0.354,0.406 0.688,0.625 0.333,0.219 10 *3 0.375,1.708 0.802,1.948 0.427,0.24 10 *1 1.51,1.667 1.979,1.948 0.469,0.281 10 *2
*1 Manual Valve
*2 Pin
*3 Manual Valve Lever


a.

Install the valve body and align the groove of the manual valve with the pin of the manual valve lever.


b.
D029011
1.031,0.406 1.313,0.167 true 2.875,0.74 3.188,0.854 3.188,0.854 2.917,0.948 true 2.896,1.313 3.198,1.396 3.198,1.396 2.885,1.729 true 2.844,1.521 3.167,1.406 true 2.531,1.854 2.333,2.052 true 1.635,1.719 1.927,2.063 true 1.354,1.646 1.604,2.052 1.604,2.052 1.354,1.854 true 1.01,1.802 1.146,2.042 true 0.542,0.885 0.188,0.979 0.188,0.979 0.469,1.365 true 0.49,1.146 0.198,0.99 true 0.969,1.146 0.198,1.76 0.198,1.76 0.677,1.823 true 0.656,1.615 0.208,1.76 true 2.313,1.302 1.74,0.917 1.74,0.917 2.313,1.083 true 1.531,0.417 1.813,0.177 true 1.375,0.063 1.563,0.24 0.188,0.177 10 A 1.188,2.021 1.333,2.177 0.146,0.156 10 A 1.99,2.031 2.156,2.177 0.167,0.146 10 A 2.229,2.031 2.396,2.177 0.167,0.146 10 A 1.885,0.063 2.063,0.229 0.177,0.167 10 C 3.24,0.781 3.385,0.938 0.146,0.156 10 C 3.25,1.323 3.385,1.5 0.135,0.177 10 C 1.667,2.031 1.833,2.177 0.167,0.146 10 B 1.615,0.833 1.781,0.979 0.167,0.146 10 B 0.052,0.896 0.219,1.115 0.167,0.219 10 B 0.052,1.688 0.26,1.938 0.208,0.25 10 B

Install the 20 bolts.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

23 mm (0.906 in.) for A

28 mm (1.10 in.) for B

36 mm (1.42 in.) for C



Hide 82.INSTALL TRANSMISSION WIRE

a.
C280866

Coat a new O-ring with ATF and install it to the transmission wire.


b.

Install the transmission wire to the case.


c.

Install the stopper plate with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


d.

Connect the 4 connectors to the 4 shift solenoid valves.


Hide 83.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

C280844

a.

Install 3 new gaskets to the oil strainer.


b.
C280845
1.313,0.281 1.469,0.479 0.156,0.198 10 C 2.021,0.365 2.177,0.563 0.156,0.198 10 B 3.083,0.583 3.24,0.781 0.156,0.198 10 A 2.833,1.854 2.99,2.052 0.156,0.198 10 A

Install the oil strainer with the 4 bolts.

Torque:
11 N*m (110 kgf*cm, 8 ft.*lbf)

HINT:

Each bolt length is indicated below.

14 mm (0.55 in.) for A

20 mm (0.79 in.) for B

23 mm (0.91 in.) for C



Hide 84.INSTALL OIL CLEANER MAGNET

C238026
2.281,0.948 2.104,1.906 2.104,1.906 1.198,0.698 true 2.104,1.885 1.74,0.948 true 2.063,1.948 2.375,2.146 0.313,0.198 10 false *1
*1 Magnet


a.

Install the 3 magnets.


Hide 85.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C238027

a.

Remove all old seal packing from the contact surfaces of the transmission case and oil pan.

NOTICE:

Be careful not to drop oil on the contact surfaces of the transmission case and oil pan.



b.

Apply seal packing to the oil pan.

Seal packing:

Toyota Genuine Seal Packing 1281,

Three Bond 1281 or equivalent

Seal diameter:

2 to 3 mm (0.0788 to 0.118 in.)



c.

Install the oil pan with the 19 bolts.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 86.INSTALL SENSOR ROTOR

a.
C220512
0.5,0.781 0.667,0.781 0.667,0.781 1.385,1.135 true 2.208,0.542 2.052,0.542 2.052,0.542 1.635,0.74 true 2.823,0.552 2.74,0.552 2.74,0.552 2.26,1.031 true 0.323,0.688 0.583,0.875 0.26,0.188 10 false *1 2.281,0.438 2.573,0.656 0.292,0.219 10 false *2 2.875,0.458 3.125,0.677 0.25,0.219 10 false *3
*1 Snap Ring
*2 Key
*3 Sensor Rotor


Using a snap ring expander, install the snap ring.


b.

Install the key to the output shaft.


c.

Align the groove of the sensor rotor with the key and install the sensor rotor.


Hide 87.INSTALL SPEEDOMETER DRIVE GEAR

a.
C238171
1.792,0.229 1.708,0.229 1.708,0.229 1.531,0.427 false 2.448,0.635 2.365,0.635 2.365,0.635 2.094,1.167 false 3.167,1.156 3.083,1.156 3.083,1.156 3.083,1.563 false 1.854,0.146 2.156,0.333 0.302,0.188 10 false *1 2.5,0.552 2.813,0.75 0.313,0.198 10 false *2 3.219,1.083 3.427,1.302 0.208,0.219 10 false *3
*1 Snap Ring
*2 Key
*3 Sensor Rotor


Install the ball to the output shaft.


b.

Align the groove of the speedometer drive gear with the ball and install the speedometer drive gear.


c.

Using a snap ring expander, install the snap ring.


Hide 88.INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL

a.

Coat the lip of a new oil seal with MP grease.


b.
C220516
1.104,0.771 0.563,0.771 0.563,0.771 1.188,0.49 false 0.25,0.708 0.74,0.99 0.49,0.281 10 SST

Using SST and a hammer, tap in the oil seal.

SST
09950-60010  (09951-00580)
09950-70010  (09951-07100)

Standard depth:

5.8 to 6.2 mm (0.228 to 0.244 in.)


NOTICE:

Be careful not to damage the lip of the oil seal.



Hide 89.INSTALL EXTENSION HOUSING DUST DEFLECTOR

a.
D005578

Using a screwdriver and hammer, tap on a new dust deflector.


Hide 90.INSTALL EXTENSION HOUSING BUSH APPLY TUBE GASKET

a.

Install the gasket to the extension housing bush apply tube.


Hide 91.INSTALL EXTENSION HOUSING BUSH APPLY TUBE

a.

Install the extension housing bush apply tube together with the gasket to the extension housing.


Hide 92.INSTALL EXTENSION HOUSING SUB-ASSEMBLY

a.

Clean the threads of the bolts.


b.

Apply adhesive to the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1324,

Three Bond 1324 or equivalent



c.
C280984
1.042,0.438 1.198,0.635 0.156,0.198 10 A 0.906,0.99 1.063,1.188 0.156,0.198 10 A 1.125,1.729 1.281,1.927 0.156,0.198 10 B 2.333,1.635 2.49,1.833 0.156,0.198 10 B 2.333,0.208 2.49,0.406 0.156,0.198 10 A 2.427,0.719 2.583,0.917 0.156,0.198 10 A

Install a new gasket and the extension housing to the transmission case with the 6 bolts.

Torque:
34 N*m (345 kgf*cm, 25 ft.*lbf)

HINT:

Each bolt length is indicated below.

45 mm (1.77 in.) for A

35 mm (1.38 in.) for B



Hide 93.INSTALL AUTOMATIC TRANSMISSION HOUSING

a.

Clean the threads of the bolts and case with non-residue solvent.


b.

Apply adhesive to the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1324,

Three Bond 1324 or equivalent



c.
C220031

Install the transmission housing with the 6 bolts.

Torque:
for 14 mm bolt : 34 N*m (345 kgf*cm, 25 ft.*lbf)
for 17 mm bolt : 57 N*m (585 kgf*cm, 42 ft.*lbf)


Hide 94.INSTALL SPEED SENSOR SP2

a.

Coat a new O-ring with ATF and install it to the sensor.


b.
G035548

Install the sensor with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 95.INSTALL SPEEDOMETER SENSOR

a.

Coat a new O-ring with ATF and install it to the sensor.


b.
G035560

Install the sensor with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 96.INSTALL SPEED SENSOR NC0

a.

Coat a new O-ring with ATF and install it to the sensor.


b.
Q003894

Install the speed sensor with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 97.INSTALL OIL COOLER TUBE UNION

a.
C238059
1.021,0.635 1.083,0.635 1.083,0.635 1.375,1.073 true 2.729,1.49 2.802,1.49 2.802,1.49 3.083,1 true 0.833,0.531 1.083,0.74 0.25,0.208 10 false *a 2.531,1.396 2.802,1.583 0.271,0.188 10 false *b
*a 5 to 9°
*b -2 to 2°


Coat 2 new O-rings with ATF and install one to each tube union.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)


b.

Install the 2 tube unions.

NOTICE:

Use the formula to calculate special torque value for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 98.INSTALL ATF TEMPERATURE SENSOR

a.
C239915

Install the bolt with the wire harness bracket.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


b.

Coat a new O-ring with ATF and install it to the sensor.


c.

Using a 19 mm union nut wrench, Install the ATF temperature sensor.

Torque:
29 N*m (300 kgf*cm, 22 ft.*lbf)

NOTICE:

Use the formula to calculate special torque value for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



d.

Connect the ATF temperature sensor clamp to the wire harness bracket.


Hide 99.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C241044

Install the park/neutral position switch to the manual valve lever shaft and temporarily install the adjusting bolt.


b.

Install a new lock washer and the nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


c.
C236140
1.365,0.094 1.521,0.271 0.156,0.177 10 N 1.75,0.417 1.906,0.594 0.156,0.177 10 R 2.271,0.313 2.427,0.49 0.156,0.177 10 P

Turn the control shaft lever LH clockwise until it stops, and then turn it counterclockwise 2 notches to set it to the N position.


d.
C213713
1.906,1.438 0.74,1.01 0.74,1.01 0.594,1.01 true 1.906,0.677 2.104,0.24 2.104,0.24 2.25,0.24 true 0.385,0.917 0.656,1.135 0.271,0.219 10 false *1 2.323,0.146 2.594,0.375 0.271,0.229 10 false *2
*1 Groove
*2 Neutral Basic Line


Align the neutral basic line with the switch groove as shown in the illustration and tighten the adjusting bolt.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


e.

Using a screwdriver, bend the tabs of the lock washer.


Hide 100.INSTALL TRANSMISSION CONTROL SHAFT LEVER LH

a.
C280864

Install the control shaft lever with the washer and nut.

Torque:
16 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 101.INSTALL BREATHER HOSE

a.

Install the breather hose with the bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 102.INSTALL DRAIN PLUG

a.

Install a new gasket and the drain plug.

Torque:
20 N*m (205 kgf*cm, 15 ft.*lbf)