Home › Drivetrain › CLUTCH › CLUTCH UNIT
RM1880E _52 Drivetrain _013218 CLUTCH _0068522 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C226320

Insert SST into the clutch disc. Then insert SST (together with the clutch disc) into the flywheel.

SST
09301-00110  

NOTICE:

Be sure to install the clutch disc so that it is facing in the correct direction.



Hide 2.INSTALL CLUTCH COVER ASSEMBLY

a.
D029623
0.427,0.031 0.74,0.313 0.313,0.281 10 false *1 2.552,1.375 3.01,1.656 0.458,0.281 10 false SST 0.844,0.281 1.135,0.51 0.292,0.229 10 false 4 0.646,1.302 0.885,1.594 0.24,0.292 10 false 2 1.51,1.927 1.792,2.177 0.281,0.25 10 false 5 2.271,1.688 2.51,1.958 0.24,0.271 10 false 3 2.281,0.375 2.51,0.615 0.229,0.24 10 false 6 1.729,0.021 2.031,0.313 0.302,0.292 10 false 1
*1 Matchmark


Align the matchmarks on the clutch cover and flywheel.


b.

Tighten the 6 bolts as described below.

i.

Determine the first bolt to be tightened by choosing the bolt closest to the knock pin.


ii.

Uniformly tighten the 6 bolts in diametrically opposite pairs relative to the position of the first bolt. Use the illustration as a reference.



c.

Lightly move SST up and down, and right and left.

SST
09301-00110  


d.

Check that the disc is in the center, and then tighten the bolts.

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)


Hide 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
D029624

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

Maximum misalignment:

0.5 mm (0.020 in.)


D029625
1.979,0.125 2.125,0.125 2.125,0.125 2.125,0.792 false 1.688,0.021 2.115,0.333 0.427,0.313 10 false SST

If the misalignment is more than the maximum, use SST to adjust the diaphragm spring tip alignment.


SST
09333-00013  


Hide 4.INSTALL RELEASE FORK SUPPORT

a.

Install the release fork support to the manual transmission unit.

Torque:
39 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 5.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.

Install the release bearing hub clip to the clutch release bearing assembly.


b.
C248521
3.25,2.083 3.333,2.083 false
V100135

Multemp 8158 Grease or equivalent


Apply Multemp 8158 grease or equivalent to the following areas:

·

The surfaces of the release fork that contact the release bearing.

·

The surfaces of the release fork that contact the push rod of the release cylinder.

·

The surfaces of the release fork that contact the release fork support.


Grease:

Multemp 8158 grease or equivalent



c.

Install the release fork sub-assembly to the clutch release bearing assembly.


d.

Install the clutch release bearing assembly together with the clutch release fork sub-assembly to the clutch housing.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



e.
C133413

Apply the clutch spline grease to the spline of the input shaft.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 6.INSTALL CLUTCH RELEASE FORK BOOT