Home › Drivetrain › R150 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY
RM1880E _52 Drivetrain _013219 R150 MANUAL TRANSMISSION / TRANSAXLE _0068528 MANUAL TRANSMISSION ASSEMBLY A

R150 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY

a.

Make sure that the knock pins are not loose, bent, damaged or scratched.


b.

Align the input shaft with the clutch disc and install the transmission to the engine.


c.
C123184
1.146,0.25 1.385,0.458 0.24,0.208 10 false A 2.396,0.26 2.635,0.469 0.24,0.208 10 false A 0.531,1.073 0.771,1.281 0.24,0.208 10 false A 0.906,1.958 1.146,2.167 0.24,0.208 10 false B 0.625,1.552 0.865,1.76 0.24,0.208 10 false B 2.396,1.938 2.635,2.146 0.24,0.208 10 false B 2.677,1.854 2.917,2.063 0.24,0.208 10 false B

Install the 7 bolts.

Torque:
for bolt A : 72 N*m (729 kgf*cm, 53 ft.*lbf)
for bolt B : 37 N*m (379 kgf*cm, 27 ft.*lbf)


Hide 2.INSTALL MANIFOLD STAY

a.
B086194
1.448,0.542 1.646,0.729 0.198,0.188 10 true A 2.292,1.875 2.49,2.063 0.198,0.188 10 false B 0.958,0.708 1.146,0.885 0.188,0.177 10 true C

Install the manifold stay with the 3 bolts.

Torque:
for bolt A : 44 N*m (449 kgf*cm, 32 ft.*lbf)
for bolt B : 30 N*m (306 kgf*cm, 22 ft.*lbf)
for bolt C : 72 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 3.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the mounting insulator with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 4.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the No. 3 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


b.

Connect the No. 3 frame crossmember sub-assembly to the rear No. 1 engine mounting insulator.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 5.INSTALL STARTER ASSEMBLY

Hide 6.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

a.

Install the clutch release cylinder with the 2 bolts.

Torque:
12 N*m (119 kgf*cm, 9 ft.*lbf)


Hide 7.CONNECT WIRE HARNESS

a.

Connect the back-up light switch connector and speedometer sensor connector.


Hide 8.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 9.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 10.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the frame crossmember with the 4 bolts and 4 nuts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 12.INSTALL FLOOR SHIFT LEVER ASSEMBLY

a.

Cover the shift lever cap with a cloth.


b.

Press down on the shift lever cap and rotate it clockwise to install the floor shift lever assembly.

HINT:

Apply MP grease to the tip of the shift lever.



Hide 13.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot with the 4 screws and 2 clips.


Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).