Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY
RM1880E _52 Drivetrain _013221 AXLE AND DIFFERENTIAL _0068544 REAR DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 1.SECURE REAR DIFFERENTIAL CARRIER ASSEMBLY

a.
C236647

Secure the differential carrier.


Hide 2.INSPECT REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C236648
2.479,1.813 2.896,2.073 0.417,0.26 10 false *a
*a 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.



Hide 3.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C236649

Using a dial indicator, check the runout of the ring gear.

Maximum runout:

0.07 mm (0.00276 in.)


If the runout is more than the maximum, replace the ring gear with a new one.



Hide 4.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C236650

Using a dial indicator, check the backlash of the ring gear.

Standard backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)


If the backlash is not within the specification, adjust the side bearing preload or perform repairs as necessary.

HINT:

Perform the measurement at 3 or more positions around the circumference of the ring gear.




Hide 8.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 10.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 11.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C236632
2.375,0.75 2.375,0.313 2.375,0.313 2.719,0.313 false 2.781,0.208 3.271,0.531 0.49,0.323 10 false SST

Using SST, remove the roller bearing (inner) from the drive pinion.

SST
09556-22010  


Hide 12.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C236656

Remove the 2 bolts and 2 adjusting nut locks.


Hide 13.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C236657
1.656,1.281 0.313,1.281 true 1.646,1.229 1,1.229 1,1.229 1,1.271 true 1.229,0.896 0.833,0.896 0.833,0.896 0.833,1.271 true 1.229,0.854 0.563,0.854 0.563,0.854 0.563,1.271 true 0.156,1.177 0.479,1.5 0.323,0.323 10 false *1
*1 Matchmark


Place matchmarks on the bearing cap and differential carrier.


b.

Remove the 4 bolts and 2 differential bearing caps.


c.

Remove the 2 adjusting nuts.


d.
C236658

Remove the rear differential case with the 2 rear differential case bearings from the differential carrier.


e.

Remove the 2 rear differential case bearings (outer) and adjusting from the differential case.

HINT:

Tag the 2 rear differential case bearings (outer) so that they can be reinstalled in the correct locations.



Hide 14.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the drive pinion and bearing spacer from the differential carrier.


Hide 15.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237656
2.333,1.031 2.604,0.469 2.604,0.469 2.698,0.469 false 2.76,0.396 3.271,0.719 0.51,0.323 10 false SST

Using SST and a press, press out the roller bearing (inner) and drive pinion plate washer from the drive pinion.

SST
09950-00020  

NOTICE:

Do not drop the drive pinion.


HINT:

If the drive pinion or ring gear is damaged, replace them as a set.



Hide 16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C238712
1.594,0.667 1.073,0.667 false 0.74,0.583 1.292,1.021 0.552,0.438 10 false SST

Using SST, remove the roller bearing (outer) from the carrier.

SST
09308-00010  


Hide 17.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C236662

Using a brass bar and hammer, tap out the rear tapered roller bearing (outer) from the carrier.

HINT:

If the bearing is damaged during removal, replace it.



Hide 18.REMOVE DIFFERENTIAL RING GEAR

a.
C236663
1.927,1.188 3.167,1.188 true 1.927,1 2.938,1 2.938,1 2.938,1.177 true 3.198,1.083 3.406,1.302 0.208,0.219 10 false *1
*1 Matchmark


Place matchmarks on the ring gear and differential case.


b.

Using a screwdriver and hammer, pry out the staked portions of the lock plates.


c.

Remove the 10 ring gear set bolts and 5 lock plates.


d.
C236664

Using a plastic-faced hammer, tap on the ring gear to separate it from the differential case.


Hide 19.INSPECT DIFFERENTIAL CASE ASSEMBLY RUNOUT

If the ring gear runout is within the specified value (refer to the "Inspect Runout of Differential Ring Gear" procedure above), skip this step.

a.

Install the rear differential case bearings (outer) to the differential case.


b.

Install the differential case to the differential carrier.


c.

Install the 2 adjusting nuts.


d.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
85 N*m (867 kgf*cm, 63 ft.*lbf)


e.
C236665

Inspect the differential case runout.

Maximum runout:

0.07 mm (0.00276 in.)



f.

Remove the 4 bolts and 2 bearing caps.


g.

Remove the 2 adjusting nuts.


h.

Remove the differential case.


i.

Remove the rear differential case bearings (outer).


Hide 20.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C236666
1.052,0.75 1.052,0.375 1.052,0.375 0.708,0.375 false 0.375,0.271 0.938,0.594 0.563,0.323 10 false SST

Using SST, remove the 2 rear differential case bearings (inner) from the differential case.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09957-04010, 09958-04011)
09950-60010  (09951-00360)

HINT:

Do not remove the case bearings when not replacing the differential case.



Hide 21.DISASSEMBLE DIFFERENTIAL CASE

a.
C236667

Using a chisel and hammer, unstake the differential case.


b.
C238726

Using a pin punch and hammer, tap out the straight pin.


c.
C236669

Remove the following parts from the differential case.

C236670
0.563,0.542 0.563,0.25 0.563,0.25 0.396,0.25 false 0.906,0.625 0.906,0.198 0.906,0.198 0.979,0.198 false 1.635,1.042 1.635,0.521 1.635,0.521 1.49,0.521 false 2.063,0.479 2.063,0.156 2.063,0.156 1.958,0.156 false 2.74,0.51 2.969,0.51 false 2.375,1.625 2.375,1.875 false 2.75,1.698 2.75,1.844 false 0.552,1.469 0.552,1.208 0.552,1.208 0.427,1.208 false 1.135,1.729 1.135,1.917 1.135,1.917 1.281,1.917 false 1.01,0.094 1.219,0.26 0.208,0.167 10 false (1) 0.156,0.146 0.365,0.313 0.208,0.167 10 false (2) 1.281,0.417 1.49,0.583 0.208,0.167 10 false (3) 1.719,0.063 1.927,0.229 0.208,0.167 10 false (4) 3.01,0.406 3.219,0.573 0.208,0.167 10 false (5) 2.292,1.885 2.5,2.052 0.208,0.167 10 false (1) 2.677,1.865 2.885,2.031 0.208,0.167 10 false (2) 1.333,1.823 1.542,1.99 0.208,0.167 10 false (4) 0.208,1.104 0.417,1.271 0.208,0.167 10 false (5)

(1) Pinion gear (2 pieces)

(2) Pinion gear thrust washer (2 pieces)

(3) Pinion shaft

(4) Side gear (2 pieces)

(5) Side gear thrust washer (2 pieces)



Hide 22.INSPECT DIFFERENTIAL GEAR KIT

a.

Check that the differential pinion and differential gear are not damaged.

If the differential pinion or differential side gear is damaged, replace the differential gear kit.



Hide 23.INSPECT DIFFERENTIAL CASE

a.

Check that the differential case is not damaged.

If the differential case is damaged, replace it.