Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL
RM1880E _52 Drivetrain _013221 AXLE AND DIFFERENTIAL _0068543 REAR DIFFERENTIAL CARRIER OIL SEAL A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER OIL SEAL  REPLACEMENT  


PROCEDURE

Hide 2.REMOVE REAR PROPELLER SHAFT ASSEMBLY

Hide 3.REMOVE REAR DRIVE PINION NUT

a.
C236628
1.292,0.542 1.292,0.208 1.292,0.208 1.948,0.208 false 1.99,0.104 2.573,0.396 0.583,0.292 10 false SST

Using SST and a hammer, loosen the staked part of the nut.

SST
09930-00010  (09931-00010, 09931-00020)


b.
C236629
2.24,1.208 2.667,1.208 false 2.719,1.125 3.198,1.448 0.479,0.323 10 false SST 0.531,0.365 0.927,0.677 0.396,0.313 10 false *a 2.188,1.74 2.708,2.063 0.521,0.323 10 false *b
*a Turn
*b Hold


Using SST to hold the companion flange in place, remove the nut.

SST
09330-00021  (09330-00030)


Hide 4.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C238731
2.198,1.521 2.198,1.781 false 2.073,1.813 2.573,2.094 0.5,0.281 10 false SST

Using SST, remove the companion flange with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



Hide 5.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

a.
C236631
2.719,1.469 2.719,1.74 false 1.417,0.802 1.552,0.302 1.552,0.302 1.74,0.302 true 1.219,1.427 1.219,1.813 true 2.594,1.75 3.094,2.042 0.5,0.292 10 false SST 1.813,0.198 2.208,0.542 0.396,0.344 10 false *1 1.156,1.833 1.479,2.115 0.323,0.281 10 false *2
*1 Oil Seal
*2 Oil Slinger


Using SST, remove the oil seal.

SST
09308-10010  


Hide 6.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Remove the oil slinger from the drive pinion.


Hide 7.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C236632
2.365,0.75 2.365,0.313 2.365,0.313 2.708,0.313 false 2.771,0.219 3.26,0.51 0.49,0.292 10 false SST

Using SST, remove the roller bearing (inner).

SST
09556-22010  


b.
C236633
1.865,0.698 1.865,0.229 1.865,0.229 2.302,0.229 false 2.354,0.146 2.906,0.469 0.552,0.323 10 false SST

Using SST, tap out the roller bearing (outer).

SST
09308-00010  


Hide 8.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.

Remove the bearing spacer from the drive pinion.


Hide 9.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.
C237515

Install a new bearing spacer.

HINT:

Make sure the spacer is installed correctly.



Hide 10.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C237516
1.448,1.875 1.448,2 1.448,2 1.792,2 false 0.875,1.938 1.448,1.938 true 1.854,1.917 2.354,2.156 0.5,0.24 10 false SST

Using SST and a hammer, tap in the roller bearing (outer).

SST
09316-60011  (09316-00011, 09316-00021)


b.

Install the roller bearing (inner).


Hide 11.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

a.
C237315

Install the oil slinger to the drive pinion.


Hide 12.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

a.

Apply MP grease to the lip of the oil seal.


b.
C236636
2.385,1.427 2.385,1.792 false 2.271,1.823 2.792,2.073 0.521,0.25 10 false SST 1.333,0.063 1.667,0.417 0.333,0.354 10 false *a
*a Oil Seal Depth


Using SST and a hammer, tap in a new oil seal.

SST
09554-30011  

Standard oil seal depth:

0.5 +/-0.3mm (0.02 +/-0.0118in.)



Hide 13.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

a.
C238732
2.229,1.521 2.229,1.781 false 2.094,1.813 2.573,2.125 0.479,0.313 10 SST

Using SST, install the companion flange with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

NOTICE:

Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



b.

Apply hypoid gear oil LSD to drive pinion thread and nut seat face.


c.
C280938
0.594,0.656 0.896,0.656 false 3.073,1.167 3.406,1.458 0.333,0.292 10 false *a 0.313,1.146 0.677,1.427 0.365,0.281 10 false *b 0.281,0.573 0.792,0.865 0.51,0.292 10 false SST
*a Turn
*b Hold


Using SST to hold the companion flange in place, install a new nut.

SST
09330-00021  (09330-00030)

Torque:
230 N*m (2345 kgf*cm, 170 ft.*lbf)

or less



Hide 14.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C236639

Using a torque wrench, measure the preload.

Standard Preload (Starting Torque):
Bearing Specified Condition
New bearing 1.5 to 2.1 N*m (16 to 21 kgf*cm, 14 to 18 in.*lbf)
Reused bearing 0.7 to 1.0 N*m (8 to 10 kgf*cm, 7 to 8 in.*lbf)


If the result is not as specified, adjust the preload (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL CARRIER ASSEMBLY>REASSEMBLY).



Hide 15.INSPECT TOTAL PRELOAD

a.
C236639

Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

Standard Total Preload:
Bearing Specified Condition
New bearing 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload
Reused bearing 0.4 to 0.5 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + drive pinion preload


If the result is not as specified, adjust the preload.


Hide 16.STAKE DRIVE PINION NUT

a.
C236640

Using a chisel and hammer, stake the nut.


Hide 17.INSTALL REAR PROPELLER SHAFT ASSEMBLY