Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM1880E _54 Brake _013226 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0068558 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1241/41  Low Battery Positive Voltage or Abnormally High Battery Positive Voltage  


DESCRIPTION

This DTC is stored when the IG1 terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit, such as the battery or generator circuit, etc.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1241/41 Low Battery Positive Voltage or Abnormally High Battery Positive Voltage Either condition is met:
1.

Both conditions continue for at least 10 seconds.

·

Vehicle speed is more than 3 km/h (2 mph).

·

The IG1 terminal voltage is below 9.5 V.


2.

All conditions continue for at least 0.2 seconds

·

Solenoid relay remains on.

·

Relay contact is open.

·

The IG1 terminal voltage is below 9.5 V.



·

ECU-IG&GAUGE fuse

·

Battery

·

Charging system

·

Power source circuit

·

Internal power supply circuit of skid control ECU (Brake actuator assembly)


-

WIRING DIAGRAM

C237089
2.25,1.219 3.594,1.531 1.344,0.313 10 false ECU-IG&GAUGE 4.677,1.063 5.146,1.406 0.469,0.344 10 false IG1 4.354,0.958 4.729,1.25 0.375,0.292 10 false 25 0.406,1.063 1.604,1.448 1.198,0.385 10 false from IG Circuit 4.677,1.771 5.458,2.219 0.781,0.448 10 false GND1 4.688,2.427 5.375,2.885 0.688,0.458 10 false GND2 4.375,2.313 4.729,2.615 0.354,0.302 10 false 24 4.406,1.667 4.781,2.031 0.375,0.365 10 false 2 4.125,3.063 4.552,3.313 0.427,0.25 10 false A13 4.125,3.25 7.031,3.625 2.906,0.375 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the skid control ECU (brake actuator assembly) connector.


c.
C117862
1.5,0.583 1.917,0.833 0.417,0.25 1.313,2.208 1.313,2.958 1.313,2.958 1.5,2.958 true 0.125,0.104 0.396,0.313 0.271,0.208 10 false *a 1.594,0.635 1.979,0.875 0.385,0.24 10 false A13 1.563,2.875 2.021,3.073 0.458,0.198 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-25 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)

OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 8

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 8
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B