Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR
RM1880E _54 Brake _013226 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0068559 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.DRAIN BRAKE FLUID

NOTICE:

Wash off brake fluid immediately if it comes in contact with any painted surface.


Hide 4.REMOVE BRAKE ACTUATOR ASSEMBLY WITH BRACKET

a.

Place tags or marks to identify the installation locations of each brake line.

C212866
1.604,0.167 2.167,0.167 false 1.479,0.26 1.479,0.302 1.479,0.302 1.198,0.302 false 1.74,0.354 1.917,0.354 false 1.229,0.573 0.594,0.573 false 5.354,0.5 4.344,0.5 false 5.563,0.313 5.302,0.094 5.302,0.094 5.125,0.094 false 5.677,0.208 5.677,0.135 5.677,0.135 6.24,0.135 false 1.542,0.802 0.844,0.802 0.844,0.802 0.844,0.573 true 6.042,0.583 6.49,0.583 6.49,0.583 6.49,1.24 false 5.729,0.813 6.49,0.813 true 0.063,0.042 0.302,0.24 0.24,0.198 10 false *A 3.792,0.042 4.01,0.24 0.219,0.198 10 false *B 2.188,0.094 2.344,0.25 0.156,0.156 10 false *1 1.01,0.219 1.25,0.417 0.24,0.198 10 false *2 1.948,0.271 2.104,0.427 0.156,0.156 10 false *3 0.438,0.51 0.594,0.667 0.156,0.156 10 false *4 4.208,0.427 4.365,0.583 0.156,0.156 10 false *1 4.906,0.031 5.177,0.26 0.271,0.229 10 false *2 6.313,0.063 6.573,0.292 0.26,0.229 10 false *3 6.427,1.25 6.583,1.406 0.156,0.156 10 false *4
*A for LHD *B for RHD


HINT:
·

*1: front wheel cylinder RH

·

*2: front wheel cylinder LH

·

*3: to rear wheel cylinder

·

*4: from master cylinder




b.

Release the latch of the actuator connector and disconnect the connector.


c.

Detach the clip form the brake actuator bracket.


d.

Using a union nut wrench, disconnect the 5 brake lines from the brake actuator.

C212867
0.083,0.01 0.26,0.208 0.177,0.198 10 false *A 3.563,0.01 3.771,0.208 0.208,0.198 10 false *B
*A for LHD *B for RHD



e.
C121396

for LHD:

Remove the 3 bolts and brake actuator with bracket.

NOTICE:

Be careful not to damage the brake tubes.



f.
C125518

for RHD:

Remove the 3 nuts and brake actuator with bracket.

NOTICE:

Be careful not to damage the brake tubes.