Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068593 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  Sound Signal Circuit between Radio Receiver and Stereo Jack Adapter  


DESCRIPTION

The No. 1 stereo jack adapter assembly sends an external device sound signal to the radio receiver assembly through this circuit.

The sound signal that has been sent is amplified by the radio receiver assembly, and then is sent to the speakers.

If there is an open or short in the circuit, sound cannot be heard from the speakers even if there is no malfunction in the radio receiver assembly or speakers.

WIRING DIAGRAM

C240216
1.674,2.933 1.885,3.088 0.212,0.154 10 9 1.674,2.429 1.885,2.583 0.212,0.154 10 7 1.674,1.911 1.885,2.065 0.212,0.154 10 5 1.674,1.406 1.885,1.561 0.212,0.154 10 6 1.674,3.438 1.885,3.592 0.212,0.154 10 8 1.674,4.573 1.885,4.727 0.212,0.154 10 3 1.674,4.068 1.885,4.223 0.212,0.154 10 2 5.358,2.863 5.57,3.018 0.212,0.154 10 11 5.693,3.042 6.116,3.196 0.423,0.154 10 AGND 5.358,2.356 5.57,2.51 0.212,0.154 10 27 5.693,2.524 6.116,2.678 0.423,0.154 10 VA- 5.358,1.848 5.57,2.002 0.212,0.154 10 26 5.693,2.005 6.116,2.16 0.423,0.154 10 VAR+ 5.358,1.34 5.57,1.494 0.212,0.154 10 28 5.693,1.501 6.116,1.655 0.423,0.154 10 VAL+ 5.332,3.555 5.639,3.72 0.307,0.165 10 G1 5.332,3.043 5.639,3.208 0.307,0.165 10 G1 5.332,2.532 5.639,2.697 0.307,0.165 10 G1 5.332,2.021 5.639,2.186 0.307,0.165 10 G1 5.332,1.509 5.639,1.674 0.307,0.165 10 G1 5.358,3.382 5.57,3.536 0.212,0.154 10 25 5.693,3.532 6.116,3.687 0.423,0.154 10 ADPG 5.386,4.503 5.598,4.657 0.212,0.154 10 3 5.386,3.998 5.598,4.153 0.212,0.154 10 2 0.629,5.773 1.894,6.119 1.265,0.346 10 No. 1 Stereo Jack Adapter Assembly 0.629,5.596 0.949,5.782 0.32,0.186 10 z1 5.673,5.773 6.695,6.119 1.022,0.346 10 Radio Receiver Assembly 5.35,4.683 5.629,4.848 0.279,0.165 10 z2 5.35,4.178 5.629,4.343 0.279,0.165 10 z2 4.021,3.26 4.615,3.435 0.594,0.175 10 Shielded 2.578,3.26 3.172,3.435 0.594,0.175 10 Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO JACK ADAPTER)
a.

Disconnect the G1 and z2 radio receiver assembly connectors.


b.

Disconnect the z1 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-28 (VAL+) - z1-6 Always Below 1 Ω
G1-26 (VAR+) - z1-5
G1-27 (VA-) - z1-7
G1-11 (AGND) - z1-9
G1-25 (ADPG) - z1-8
z2-2 - z1-2
z2-3 - z1-3
G1-28 (VAL+) - Body ground Always 10 kΩ or higher
G1-26 (VAR+) - Body ground
G1-27 (VA-) - Body ground
G1-11 (AGND) - Body ground
G1-25 (ADPG) - Body ground
z2-2 - Body ground
z2-3 - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR