Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)
RM1880E _56 Audio / Visual / Telematics _013234 AUDIO / VIDEO _0068593 AUDIO AND VISUAL SYSTEM(for Radio Receiver Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio Receiver Type)  CB-13  USB Over Current Detection  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area Note
CB-13 USB Over Current Detection An "iPod" or USB device overcurrent malfunction
·

"iPod" or USB device

·

Harness or connector

·

No. 1 stereo jack adapter assembly

·

Radio receiver assembly


USB Audio System

WIRING DIAGRAM

C240166
0.597,1.683 0.937,1.85 0.34,0.167 10 z1 0.597,1.851 1.799,2.208 1.202,0.357 10 No. 1 Stereo Jack Adapter Assembly 5.193,1.683 5.532,1.85 0.34,0.167 10 z2 5.235,1.094 5.368,1.261 0.134,0.167 10 4 5.235,0.492 5.387,0.659 0.152,0.167 10 1 1.844,1.094 1.973,1.261 0.129,0.167 10 4 1.844,0.492 1.996,0.659 0.152,0.167 10 1 5.193,1.851 7.005,2.018 1.812,0.167 10 Radio Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:

The data stored on the USB device or "iPod" may be changed or lost due to malfunctions, repairs, system errors, etc. Therefore, when repairs are to be performed, explain this to the customer and obtain their consent prior to performing repairs.


PROCEDURE

1.REPLACE USB DEVICE OR "iPod"
a.

Disconnect the USB device or "iPod" from the stereo jack adapter assembly.


b.

Turn the ignition switch off.

HINT:

When this DTC has been stored, it is necessary to turn off the ignition switch to make it possible for the vehicle to recognize a new device when it is connected.



c.

Turn the ignition switch to ACC.


d.

Connect a known good USB device or "iPod" to the stereo jack adapter assembly.


Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC

b.

Check for DTCs and check if the same DTC occurs again.

HINT:

If DTCs are output frequently, replace the radio receiver assembly.


OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

USB DEVICE OR "iPod" WAS DEFECTIVE

NG

3.CHECK RADIO RECEIVER ASSEMBLY
3.CHECK RADIO RECEIVER ASSEMBLY
a.

Disconnect the z1 No. 1 stereo jack adapter assembly connector.


b.
C225529
1.521,0.344 1.938,0.594 0.417,0.25 0.24,0.167 0.552,0.427 0.313,0.26 10 false *a 1.667,0.385 1.969,0.625 0.302,0.24 10 false z1
*a Front view of wire harness connector
(to No. 1 Stereo Jack Adapter Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z1-1 - z1-4 Always 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 1 STEREO JACK ADAPTER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO JACK ADAPTER)
4.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO JACK ADAPTER)
a.

Disconnect the z2 radio receiver assembly connector.


b.

Disconnect the z1 No. 1 stereo jack adapter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z2-1 - z1-1 Always Below 1 Ω
z2-4 - z1-4 Always Below 1 Ω
z2-1 - Body ground Always 10 kΩ or higher
z2-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR