GENERAL
This TOYOTA parking assist-sensor system uses the No. 1 ultrasonic sensors to detect any obstacles to the rear of the vehicle. The system then informs the driver of the distance between the sensors and the obstacles as well as their positions by sounding the No. 1 clearance warning buzzer.
FUNCTION OF COMPONENTS
| Component | Function |
|---|---|
| No. 1 ultrasonic sensor | Consists of a sensor portion that transmits and receives ultrasonic waves and a pre-amplifier that amplifies them. The No. 1 ultrasonic sensor outputs the ultrasonic transmission and reception signals to the rear clearance warning ECU assembly. |
| Back sonar or clearance sonar switch assembly | Turns the TOYOTA parking assist-sensor system on and off. |
| No. 1 clearance warning buzzer | Emits an intermittent sound to inform the driver that the rear clearance warning ECU assembly has detected an obstacle within the predetermined ranges. |
| Rear clearance warning ECU assembly | Judges the approximate distance between the vehicle and the obstacle based on the signals from the No. 1 ultrasonic sensors and sends the buzzer signal to the No. 1 clearance warning buzzer. |
| Combination meter assembly | Receives the vehicle speed signal from vehicle speed sensor, and then sends the signal to the rear clearance warning ECU assembly. |
| Park/neutral position switch assembly*1 | Turns on when the shift lever is moved to R. |
| Back-up light switch assembly*2 | Turns on when the shift lever is moved to R. |
*1: for Automatic Transmission
*2: for Manual Transmission
OPERATION EXPLANATION
The No. 1 ultrasonic sensors operate under the conditions shown in the table below.
| Sensor | Operating Condition |
|---|---|
| No. 1 Ultrasonic Sensor | ·
Ignition switch ON ·
Back sonar or clearance sonar switch is on ·
Shift lever moved to R |
When the system operates, the rear clearance warning ECU assembly transmits ultrasonic waves from the No. 1 ultrasonic sensors. If these waves encounter an obstacle within one or more of the sensors' ranges, the waves are reflected back to the sensors, which transmit them to the rear clearance warning ECU assembly. Based on this information, the rear clearance warning ECU assembly sends signals to the No. 1 clearance warning buzzer. The distance between the obstacle and the vehicle is then indicated by the sounding of the buzzer.
Refer to Operation Check for operation details (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>OPERATION CHECK).
COMMUNICATION SIGNALS OF COMPONENTS
Allocation refers to the process of the rear clearance warning ECU assembly setting aside IDs for the sensors.
The sensors are connected in a "daisy chain".
Initialization mode:
An ID is allocated to each sensor and sensor diagnosis is performed.
When any of the following conditions are met, the rear clearance warning ECU assembly provides power to the No. 1 ultrasonic sensor (rear sensor RH):
The ignition switch is turned to ON.
The sensor operating conditions (described previously) are met and the back sonar or clearance sonar switch is turned on.
The vehicle speed is below 10 km/h (6.2 mph).
After the power is supplied, the No. 1 ultrasonic sensor (rear sensor RH) enters standby mode to receive an ID from the ECU. When a certain amount of time has elapsed, the ECU sends an ID allocation signal to this sensor.
The No. 1 ultrasonic sensor (rear sensor RH) receives the ID allocation signal from the ECU and performs self-diagnosis. When the sensor self-diagnosis is complete, the ECU sends an ID allocation confirmation signal to the sensor.
After the ID allocation confirmation is performed, the ECU provides power to the No. 1 ultrasonic sensor (rear sensor LH) via the No. 1 ultrasonic sensor (rear sensor RH). In the same manner as the No. 1 ultrasonic sensor (rear sensor RH), the No. 1 ultrasonic sensor (rear sensor LH) enters standby mode. When a certain amount of time has elapsed, the ECU sends an ID allocation signal to the No. 1 ultrasonic sensor (rear sensor LH)
Initialization ends when ID allocation to all ultrasonic sensors is complete.
Detection mode:
After initialization mode is complete, the system switches into detection mode. In detection mode, the rear clearance warning ECU assembly sends information request signals and sensor activation signals to the No. 1 ultrasonic sensors and receives detection result signals from the sensors.
The rear clearance warning ECU assembly regularly sends ID signals, information request signals, and sensor activation signals to each No. 1 ultrasonic sensor according to the communication schedule.
When a certain amount of time has elapsed (sensor detection operation is complete), the rear clearance warning ECU assembly sends an ID signal to the sensor to receive a detection result signal.
The No. 1 ultrasonic sensor sends a detection result signal or detection information signal to the ECU.
The above operation is performed repeatedly for each ultrasonic sensor.