Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM
RM1880E _56 Audio / Visual / Telematics _013235 PARK ASSIST / MONITORING _0068601 TOYOTA PARKING ASSIST-SENSOR SYSTEM J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM  Clearance Warning Buzzer Circuit  


DESCRIPTION

The rear clearance warning ECU assembly receives the No. 1 ultrasonic sensor signal to sound the No. 1 clearance warning buzzer.

WIRING DIAGRAM

E224551
2.635,1.646 3.177,1.885 0.542,0.24 10 false G73 2.906,1.167 3.385,1.417 0.479,0.25 10 false Z+ 4.302,1.167 4.719,1.479 0.417,0.313 10 false Z- 2.635,1.865 4.938,2.271 2.302,0.406 10 false No. 1 Clearance Warning Buzzer 5.333,1.719 5.76,1.906 0.427,0.188 10 false T1 5.333,1.979 6.865,2.438 1.531,0.458 10 false Rear Clearance Warning ECU Assembly 5.719,1.031 6.208,1.354 0.49,0.323 10 false BBZ 5.365,0.865 5.563,1.031 0.198,0.167 10 false 12 2.656,0.865 2.948,1.115 0.292,0.25 10 false 1 4.583,0.854 4.823,1.115 0.24,0.26 10 false 2 1.5,1.25 2.76,1.656 1.26,0.406 10 false ECU-IG&GAUGE 0.219,1 1,1.552 0.781,0.552 10 false from Ignition Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (NO. 1 CLEARANCE WARNING BUZZER - REAR CLEARANCE WARNING ECU ASSEMBLY)
a.

Disconnect the G73 No. 1 clearance warning buzzer connector.


b.

Disconnect the T1 rear clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G73-2 (Z-) - T1-12 (BBZ) Always Below 1 Ω
G73-2 (Z-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (NO. 1 CLEARANCE WARNING BUZZER - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (NO. 1 CLEARANCE WARNING BUZZER - BATTERY)
a.

Disconnect the G73 No. 1 clearance warning buzzer connector.


b.
E224538
1.531,0.344 1.948,0.594 0.417,0.25 1.521,1.448 1.156,1.656 1.156,1.656 0.938,1.656 true 0.052,0.021 0.688,0.417 0.635,0.396 10 false *a 1.604,0.385 2.031,0.708 0.427,0.323 10 false G73 0.708,1.573 1.167,2 0.458,0.427 10 false Z+
*a Front view of wire harness connector
(to No. 1 Clearance Warning Buzzer)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G73-1 (Z+) - Body ground Ignition switch ON 11 to 14 V
G73-1 (Z+) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE NO. 1 CLEARANCE WARNING BUZZER
a.

Result:
Proceed to
NEXT



NEXT

4.CHECK NO. 1 CLEARANCE WARNING BUZZER OPERATION
4.CHECK NO. 1 CLEARANCE WARNING BUZZER OPERATION
a.

Check that the No. 1 clearance warning buzzer sounds.

OK:

No. 1 clearance warning buzzer sounds.



Result:
Proceed to
OK
NG



OK

END (NO. 1 CLEARANCE WARNING BUZZER IS DEFECTIVE)

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE