Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068615 ENGINE IMMOBILISER SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  B2799  Engine Immobiliser System Malfunction  


DESCRIPTION

This DTC is output when one of the following occurs: 1) the ECM detects errors in its own communications with the transponder key ECU assembly; 2) the ECM detects errors in the communication lines; or 3) the ECU communication ID between the transponder key ECU assembly and ECM is different and an engine start is attempted. Before troubleshooting for this DTC, make sure no transponder key ECU DTCs are present. If present, troubleshoot the transponder key ECU DTCs first.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*1):
·

A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.

·

A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.


·

Harness or connector

·

Transponder key ECU assembly

·

ECM


ECM
DTC Output Confirmation Operation

Either condition is met:

·

Within 10 seconds of an engine start operation being performed (with the shift lever in P and the brake pedal*2 or clutch pedal*3 depressed, turn the ignition switch to ON). If there is a malfunction, the engine stops (communication begins within 3 seconds of the engine start operation being performed, and DTCs are stored after 6 seconds).

·

10 seconds after the ignition switch is turned to ON after reconnecting the cable to the negative (-) battery terminal (communication begins within 3 seconds of the ignition switch being turned to ON, and DTCs are stored after 6 seconds).




*1: Only output while a malfunction is present.

*2: for Automatic Transmission

*3: for Manual Transmission


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started. -

Related Data List and Active Test
DTC Code Data List and Active Test
B2799 -

WIRING DIAGRAM

B281160
1.156,2.104 1.875,2.49 0.719,0.385 10 false ECM 5.49,0.917 5.979,1.24 0.49,0.323 10 false EFIO 5.49,1.385 6.01,1.667 0.521,0.281 10 false EFII 1.5,0.917 2.604,1.51 1.104,0.594 10 false IMI 1.438,1.385 2.219,1.979 0.781,0.594 10 false IMO 5.198,0.813 5.479,1.125 0.281,0.313 10 false 13 5.198,1.292 5.469,1.625 0.271,0.333 10 false 12 4.906,1.917 5.406,2.302 0.5,0.385 10 false G26 4.906,2.073 7,2.563 2.094,0.49 10 false Transponder Key ECU Assembly 1.781,0.802 2.281,1.063 0.5,0.26 10 false 16 1.156,1.958 1.781,2.25 0.625,0.292 10 false G88 1.781,1.292 2.594,1.76 0.813,0.469 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

The fixed 12 V power source voltage in the ECM is output through a resistance from terminal IMI. The transponder key ECU assembly grounds or does not ground this power source voltage accordingly.

·

The fixed 12 V power source voltage in the transponder key ECU assembly is output through a resistance from terminal EFII. The ECM grounds or does not ground this power source voltage accordingly.

·

When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:

After troubleshooting for this DTC, make sure B2799 is not present. If present, troubleshoot the SFI system DTCs next.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.REREGISTER ECU COMMUNICATION ID
3.REREGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


Result:
Proceed to
NEXT



NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Check for the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)

NG

6.CHECK CONNECTION OF CONNECTOR
6.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)

NG

CONNECT CONNECTOR CORRECTLY

7.CHECK HARNESS AND CONNECTOR (SFI OR ECD COMMUNICATION LINE)
a.

Disconnect the G26 transponder key ECU assembly connector.


b.

Disconnect the G88 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G26-13 (EFIO) - G88-16 (IMI) Always Below 1 Ω
G26-12 (EFII) - G88-15 (IMO) Always Below 1 Ω
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always 10 kΩ or higher
G26-12 (EFII) or G88-15 (IMO) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G26-13 (EFIO) or G88-16 (IMI) - Body ground Always Below 1 V
G26-12 (EFII) or G88-15 (IMO) - Body ground Always Below 1 V



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

Click hereEngine / Hybrid System>2TR-FE ENGINE CONTROL>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.REREGISTER ECU COMMUNICATION ID
9.REREGISTER ECU COMMUNICATION ID
a.

Reregister the ECU - ECM communication ID (Refer to Service Bulletin).


Result:
Proceed to
NEXT



NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTC
11.CHECK FOR DTC
a.

Check for the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61
OK:

DTC B2799 is not output.



Result:
Proceed to
OK
NG



OK

END (ECM IS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY