Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068615 ENGINE IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM  Engine does not Start  


DESCRIPTION

If the engine does not start and no DTCs are output, there is an open or short circuit between the ECM or transponder key ECU assembly.

WIRING DIAGRAM

B281160
1.156,2.104 1.875,2.49 0.719,0.385 10 false ECM 5.49,0.917 5.979,1.24 0.49,0.323 10 false EFIO 5.49,1.385 6.01,1.667 0.521,0.281 10 false EFII 1.5,0.917 2.604,1.51 1.104,0.594 10 false IMI 1.438,1.385 2.219,1.979 0.781,0.594 10 false IMO 5.198,0.813 5.479,1.125 0.281,0.313 10 false 13 5.198,1.292 5.469,1.625 0.271,0.333 10 false 12 4.906,1.917 5.406,2.302 0.5,0.385 10 false G26 4.906,2.073 7,2.563 2.094,0.49 10 false Transponder Key ECU Assembly 1.781,0.802 2.281,1.063 0.5,0.26 10 false 16 1.156,1.958 1.781,2.25 0.625,0.292 10 false G88 1.781,1.292 2.594,1.76 0.813,0.469 10 false 15

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting this symptom, make sure no engine immobiliser system DTCs, SFI system DTCs are present. If present, troubleshoot the engine immobiliser system DTCs or blocking system DTCs first.

·

When replacing the transponder key ECU assembly or ECM, refer to the Service Bulletin.



PROCEDURE

1.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)
a.
B274402
0.583,1.135 0.969,1.375 0.385,0.24 1.292,1.427 1.094,1.792 1.094,1.792 0.896,1.792 true 1.552,1.417 1.375,2.146 1.375,2.146 1.177,2.146 true 0.063,0.042 0.448,0.365 0.385,0.323 10 false *a 0.083,2.427 0.719,2.854 0.635,0.427 10 false *1 0.271,3.354 1.01,3.896 0.74,0.542 10 false GND 0.563,1.708 1.219,1.938 0.656,0.229 10 false GND 0.656,1.177 0.938,1.354 0.281,0.177 10 false G26 0.813,2.063 1.375,2.365 0.563,0.302 10 false EFIO
*1 Waveform
*a Component with harness connected
(Transponder Key ECU Assembly)


Using an oscilloscope, check the waveform.

Measurement Condition:
Item Content
Tester Connection G26-13 (EFIO) - G26-16 (GND)
Tool Setting 10 V/DIV., 100 ms./DIV.
Condition Ignition switch ON


HINT:
·

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

·

Check the waveform when the security indicator light assembly is off (the engine immobiliser system is unset). If the security indicator light assembly does not turn off (the engine immobiliser system cannot be unset), refer to the "Problem Symptoms Table.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM>PROBLEM SYMPTOMS TABLE



OK:

Waveform is output normally (refer to illustration).


Result:
Result Proceed to
NG (stuck LOW: 1 V or less) A
NG (stuck HI: 10 V) B
OK C




A

2.REPLACE TRANSPONDER KEY ECU ASSEMBLY

B

C

5.REGISTER ECU COMMUNICATION ID
2.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Temporarily replace the transponder key ECU assembly with a new one (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

3.REGISTER ECU COMMUNICATION ID
3.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)

5.REGISTER ECU COMMUNICATION ID
a.

Register the ECU - ECM communication ID (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECU COMMUNICATION ID IS NOT REGISTERED CORRECTLY)