Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068616 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  ECU Power Source Circuit  


DESCRIPTION

This circuit provides power to operate the theft warning ECU assembly.

WIRING DIAGRAM

B276315
5.865,0.313 6.135,0.49 0.271,0.177 10 false +B1 5.667,0.24 5.781,0.417 0.115,0.177 10 false 3 5.865,1.396 6.021,1.573 0.156,0.177 10 false E 5.667,1.313 5.781,1.49 0.115,0.177 10 false 1 5.865,0.875 6.135,1.052 0.271,0.177 10 false +B2 4.677,0.5 5.135,0.677 0.458,0.177 10 false ECU-B 3.708,0.49 4.063,0.667 0.354,0.177 10 false DCC 1.49,0.354 2.302,0.531 0.813,0.177 10 false from Battery 4.146,1.063 4.583,1.24 0.438,0.177 10 false DOOR 5.729,1.948 6.115,2.104 0.385,0.156 10 false G124 5.729,2.094 6.75,2.448 1.021,0.354 10 false Theft Warning ECU Assembly 5.615,0.792 5.792,0.969 0.177,0.177 10 false 12

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the theft warning ECU assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)>REGISTRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - BATTERY AND BODY GROUND)
a.

Disconnect the G124 theft warning ECU assembly connector.


B291783
1.438,0.365 1.938,0.625 0.5,0.26 0.354,0.823 0.521,0.823 0.521,0.823 0.792,1.135 true 0.917,0.521 1.094,0.521 1.094,0.521 1.26,1.135 true 2.979,0.76 2.802,0.76 2.802,0.76 2.635,1.135 true 0.063,0.042 0.229,0.219 0.167,0.177 10 false *a 0.594,0.427 0.875,0.604 0.281,0.177 10 false +B1 1.521,0.406 1.885,0.583 0.365,0.177 10 false G124 3,0.667 3.281,0.844 0.281,0.177 10 false +B2 0.198,0.74 0.333,0.917 0.135,0.177 10 false E
*a Front view of wire harness connector
(to Theft Warning ECU Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G124-1 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G124-3 (+B1) - Body ground Always 11 to 14 V
G124-12 (+B2) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR