Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM
RM1880E _58 Vehicle Interior _013238 THEFT DETERRENT / KEYLESS ENTRY _0068616 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Horn Circuit  


DESCRIPTION

When the theft deterrent system is changed from the armed state to the alarm sounding state, the theft warning ECU assembly turns on the HORN relay, causing the vehicle horn to sound at 0.4 seconds intervals.

WIRING DIAGRAM

B278730
5.885,0.927 6.323,1.104 0.438,0.177 10 false HORN 5.073,2.542 5.781,2.677 0.708,0.135 10 false A14 5.073,2.677 7.156,2.99 2.083,0.313 10 false Low Pitched Horn Assembly 5.26,1.583 5.938,1.729 0.677,0.146 10 false G124 5.26,1.708 7.156,2.188 1.896,0.479 10 false Theft Warning ECU Assembly 2.208,1.813 3.677,2.021 1.469,0.208 10 false No. 1 Integration Relay 2.583,2.542 3.813,2.771 1.229,0.229 10 false A15 2.583,2.677 4.76,3.177 2.177,0.5 10 false High Pitched Horn Assembly 2.927,1.625 3.365,1.802 0.438,0.177 10 false HORN 2.021,1.083 2.458,1.26 0.438,0.177 10 false HORN 0.156,0.927 0.938,1.104 0.781,0.177 10 false from Battery 5.625,0.844 5.802,1.021 0.177,0.177 10 false 24 3.99,0.958 4.167,1.135 0.177,0.177 10 false 1I 4.031,0.74 4.208,0.917 0.177,0.177 10 false 7 4.781,2.479 5.208,2.656 0.427,0.177 10 false 1 2.313,2.448 2.833,2.625 0.521,0.177 10 false 1 1.583,0.958 2.063,1.156 0.479,0.198 10 false 1H 1.635,0.74 1.74,0.917 0.104,0.177 10 false 1 4.021,1.354 4.198,1.531 0.177,0.177 10 false 1I 4.031,1.146 4.208,1.323 0.177,0.177 10 false 8

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the theft warning ECU assembly, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Theft Deterrent System)>REGISTRATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HORN ASSEMBLY
a.

Press the horn switch and check if the horn sounds.

Result:
Result Proceed to
Horn sounds A
Horn does not sound B




A

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - NO. 1 INTEGRATION RELAY [HORN RELAY])

B

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING ECU - NO. 1 INTEGRATION RELAY [HORN RELAY])
a.

Disconnect the G124 theft warning ECU assembly connector.


b.

Disconnect the 1I No. 1 integration relay connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G124-24 (HORN) - 1I-7 Always Below 1 Ω
G124-24 (HORN) or 1I-7 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR