Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3. The DTCs are communicated through SRS warning light blinking patterns.

HINT:

When one or more of the warning lights blink continuously, the cause may be a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in an ECU.


WIRING DIAGRAM

C240459
5.51,2.75 6.948,3.125 1.438,0.375 10 Center Airbag Sensor 5.802,1.167 6.177,1.448 0.375,0.281 10 TC 0.958,2.281 1.375,2.594 0.417,0.313 10 G18 0.958,2.458 1.448,2.792 0.49,0.333 10 DLC3 1.583,1.156 1.958,1.458 0.375,0.302 10 TC 1.552,1.906 1.917,2.24 0.365,0.333 10 CG 5.521,1.052 5.896,1.333 0.375,0.281 10 15 1.844,1.052 2.188,1.333 0.344,0.281 10 13 1.885,1.823 2.167,2.094 0.281,0.271 10 4 5.5,2.594 5.885,2.875 0.385,0.281 10 G53

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (DLC3 - CENTER AIRBAG SENSOR AND BODY GROUND)
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the G53 connector from the center airbag sensor.


d.
C237254
1.51,0.125 1.927,0.375 0.417,0.25 1.49,1.604 1.906,1.854 0.417,0.25 0.677,1.135 1.604,0.854 true 2.646,1.375 1.844,1.188 true 2.552,2.76 1.76,2.542 true 0.156,0.104 0.448,0.417 0.292,0.313 10 false *a 0.156,1.625 0.448,1.938 0.292,0.313 10 false *b 1.583,0.167 1.958,0.469 0.375,0.302 10 false G18 0.427,1.073 0.802,1.375 0.375,0.302 10 false CG 2.677,1.333 3.052,1.635 0.375,0.302 10 false TC 2.594,2.656 2.969,2.958 0.375,0.302 10 false TC 1.573,1.646 1.948,1.948 0.375,0.302 10 false G53
*a Front view of DLC3
*b Rear view of wire harness connector
(to Center Airbag Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G18-13 (TC) - G53-15 (TC) Always Below 1 Ω
G18-4 (CG) - Body ground Always Below 1 Ω
G53-15 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR