Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

The SRS warning light is located on the combination meter. When the ignition switch is turned from off to ON, the SRS warning light illuminates. If the SRS is normal, the SRS warning light turns off automatically after approximately 6 seconds. If there is a malfunction in the SRS, the SRS warning light remains illuminated even after approximately 6 seconds have passed. When terminals TC and CG of the DLC3 are connected, the DTCs are communicated through SRS warning light blinking patterns.

WIRING DIAGRAM

C237174
3.802,2.083 4.281,2.427 0.479,0.344 10 SW 3.146,2.656 3.573,2.99 0.427,0.333 10 IG+ 3.156,4.26 3.604,4.542 0.448,0.281 10 EP 3.052,5.625 3.542,5.938 0.49,0.313 10 G19 5.75,5.594 6.177,5.906 0.427,0.313 10 G53 0.135,0.865 1.521,1.313 1.385,0.448 10 from Ignition Switch 2.125,1.021 2.51,1.333 0.385,0.313 10 IGN 2.104,2.813 2.573,3.135 0.469,0.323 10 MET 2.917,2.563 3.292,2.906 0.375,0.344 10 21 2.917,4.146 3.24,4.5 0.323,0.354 10 22 6.146,2.073 6.531,2.375 0.385,0.302 10 LA 4.135,1.979 4.5,2.302 0.365,0.323 10 20 5.875,1.99 6.26,2.302 0.385,0.313 10 14 5.865,3.563 6.208,3.896 0.344,0.333 10 25 5.875,4.156 6.26,4.479 0.385,0.323 10 26 6.146,3.677 6.49,4 0.344,0.323 10 E1 6.146,4.271 6.469,4.594 0.323,0.323 10 E2 5.875,0.771 6.229,1.104 0.354,0.333 10 21 6.146,0.865 6.542,1.156 0.396,0.292 10 IG2 3.052,5.802 4.51,6.219 1.458,0.417 10 Combination Meter 5.75,5.781 7.156,6.198 1.406,0.417 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTION OF CONNECTOR

NG

RECHARGE OR REPLACE BATTERY

2.CHECK CONNECTION OF CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and combination meter.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF CENTER AIRBAG SENSOR)
a.

Disconnect the connector from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


C198548
0.417,0.729 0.833,0.979 0.417,0.25 1.24,1.906 1.583,1.375 true 2.063,1.865 1.729,1.375 true 2.198,1.354 2.615,1.354 true 1.552,0.281 1.875,0.583 0.323,0.302 10 false *a 0.5,0.781 0.938,1.104 0.438,0.323 10 false G53 1.052,1.875 1.417,2.167 0.365,0.292 10 false E2 2.104,1.875 2.427,2.177 0.323,0.302 10 false E1 2.677,1.271 3,1.573 0.323,0.302 10 false IG2
*a Rear view of wire harness connector
(to Center Airbag Sensor)


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G53-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-25 (E1) - Body ground Always Below 1 Ω
G53-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SOURCE VOLTAGE OF COMBINATION METER)
a.

Disconnect the G19 connector from the combination meter.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


H100390
1.479,0.5 1.896,0.75 0.417,0.25 0.5,1.729 0.667,1.406 true 0.948,1.729 0.802,1.417 true 0.125,0.073 0.469,0.406 0.344,0.333 10 false *a 1.563,0.552 2.01,0.865 0.448,0.313 10 false G19 0.344,1.729 0.792,2.042 0.448,0.313 10 false IG+ 0.979,1.719 1.323,2 0.344,0.281 10 false EP
*a Front view of wire harness connector
(to Combination Meter)


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G19-21 (IG+) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-22 (EP) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - COMBINATION METER)
a.
H100391
0.198,1.49 0.615,1.74 0.417,0.25 0.208,3.01 0.625,3.26 0.417,0.25 1.917,1.635 2.667,2.24 true 2.833,3.656 3.031,3.469 true 0.156,0.104 0.5,0.406 0.344,0.302 10 false *a 0.177,2.656 0.521,2.958 0.344,0.302 10 false *b 0.281,1.542 0.625,1.844 0.344,0.302 10 false G53 0.281,3.063 0.625,3.365 0.344,0.302 10 false G19 2.688,2.208 3.031,2.51 0.344,0.302 10 false LA 3.052,3.375 3.396,3.677 0.344,0.302 10 false SW
*a Rear view of wire harness connector
(to Center Airbag Sensor)
*b Front view of wire harness connector
(to Combination Meter)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-14 (LA) - G19-20 (SW) Always Below 1 Ω
G53-14 (LA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SRS WARNING LIGHT (OPERATION)

NG

REPLACE HARNESS AND CONNECTOR

6.CHECK SRS WARNING LIGHT (OPERATION)
a.

Connect the connector to the combination meter.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 second.


c.

Turn the ignition switch to ON.


d.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

7.CHECK CENTER AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

7.CHECK CENTER AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch to ON.


b.
C198548
0.417,0.719 0.833,0.969 0.417,0.25 1.865,1.167 2.521,1.573 true 1.552,0.281 1.875,0.583 0.323,0.302 10 false *a 0.49,0.771 0.813,1.073 0.323,0.302 10 false G53 2.552,1.521 2.875,1.823 0.323,0.302 10 false LA
*a Rear view of wire harness connector
(to Center Airbag Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G53-14 (LA) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.REPLACE CENTER AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

8.REPLACE CENTER AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



d.

Check the SRS warning light condition.

OK:

SRS warning light illuminates normally.



Result:
Proceed to
OK
NG



OK

END (CENTER AIRBAG SENSOR IS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY