Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY
RM1880E _58 Vehicle Interior _013243 SEAT _0068642 FRONT SEAT ASSEMBLY A

SEAT  FRONT SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

a.
B278193

Install the front seat cushion edge protector LH as shown in the illustration.


Hide 2.INSTALL LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY LH

a.
B278194
0.292,1.563 0.323,1.615 false 3.25,2.083 3.333,2.083 false
V100135

MP Grease


for Driver Side:

i.

Apply MP grease to the locations shown in the illustration.



b.

Using a T40 "TORX" socket wrench, install the lower reclining adjuster arm sub-assembly LH with the 2 "TORX" bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

for Front Passenger Side:

Install the lower reclining adjuster arm sub-assembly LH with the 3 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 3.INSTALL LOWER RECLINING ADJUSTER ARM SUB-ASSEMBLY RH

a.

for Driver Side:

HINT:

Use the same procedure described for the LH side.



b.

for Front Passenger Side:

HINT:

Use the same procedure described for the LH side.



Hide 4.INSTALL VERTICAL ADJUSTING SHAFT SUB-ASSEMBLY (for Driver Side)

a.
B278195
3.25,2.083 3.333,2.083 false
V100135

MP Grease


Apply MP grease to the locations shown in the illustration.


b.
B277650

Connect the vertical adjusting shaft sub-assembly to the 2 lower reclining adjuster arms to install it.


c.
B278196
0.802,0.146 0.927,0.146 0.927,0.146 1.25,0.396 true 0.615,0.083 0.958,0.313 0.344,0.229 10 false *1
*1 Vertical Travel Link


Connect the 2 vertical travel links to the vertical adjusting shaft sub-assembly.


d.

Install 2 new E-rings.


e.

Temporarily install the vertical seat adjuster knob LH.


f.
B278197
3.042,0.458 2.469,0.458 true 1.542,0.469 0.906,0.469 true 1.76,4.49 1.635,4.49 1.635,4.49 1.073,4.198 true 2.063,4.01 1.927,4.01 1.927,4.01 1.406,3.719 true 0.375,2.875 0.51,2.875 0.51,2.875 0.969,3.688 true 3.073,0.354 3.354,0.594 0.281,0.24 10 false *a 0.708,0.375 0.979,0.594 0.271,0.219 10 false *b 1.833,4.396 2.083,4.563 0.25,0.167 10 false *1 2.146,3.927 2.396,4.167 0.25,0.24 10 false *2 0.188,2.792 0.469,3.031 0.281,0.24 10 false *3
*1 Vertical Adjusting Shaft Sub-assembly
*2 Lower Reclining Adjuster Arm Sub-assembly
*3 Hole
*a Arrow A
*b Arrow B


Turn the vertical seat adjuster knob LH as much as possible in the direction indicated by arrow A in the illustration.


g.

Mesh the gear of the vertical adjusting shaft sub-assembly with the gear of the lower reclining adjuster arm sub-assembly.


h.

Align the holes of the vertical adjusting shaft sub-assembly and lower reclining adjuster arm sub-assembly by turning the vertical seat adjuster knob LH in the direction indicated by arrow B in the illustration.


i.

Remove the vertical seat adjuster knob LH.


Hide 5.INSTALL FRONT NO. 2 SEAT ADJUSTER PIN LH (for Driver Side)

a.

Using a 6 mm socket hexagon wrench, install the front No. 2 seat adjuster pin LH.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 6.INSTALL SEAT SPRING (for Driver Side)

a.

Temporarily install the vertical seat adjuster knob LH.


b.

Turn the vertical seat adjuster knob LH clockwise and move the lower reclining adjuster arm sub-assembly to the uppermost position.


c.

Remove the vertical seat adjuster knob LH.


d.
B278198

Install the seat spring as shown in the illustration.


e.

Using pliers, push together the tabs that hold the seat spring.


Hide 7.INSTALL SEAT TRACK HANDLE SUB-ASSEMBLY LH

a.
B278199
3.25,3.333 3.333,3.333 false
V100135

MP Grease


Apply MP grease to the locations shown in the illustration.


b.
B278200

B278184

Attach the 2 springs to install the seat track handle sub-assembly LH as shown in the illustration.

HINT:

The seat track handle sub-assembly LH will get caught on the springs when installing it. Detach the springs to install the seat track handle sub-assembly LH.



Hide 8.INSTALL FRONT SEAT ADJUSTER ROD (for Driver Side)

a.

Install the front seat adjuster rod with the 2 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 9.INSTALL FRONT SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Install the front seat cushion frame sub-assembly LH with the 4 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 10.INSTALL FRONT SEAT CUSHION PROTECTOR

a.
B276738

Install the 2 front seat cushion protectors.


Hide 11.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



B278517
6.208,0.25 6.094,0.25 false 6.094,0.25 6.01,0.698 false 0.521,0.125 0.74,0.292 0.219,0.167 10 false *A 3.365,0.125 3.583,0.292 0.219,0.167 10 false *B 6.229,0.146 6.427,0.313 0.198,0.167 10 false *1
*A for Cloth Seat *B for Leather Seat



b.

Attach the hooks to install the separate type front seat cushion cover with pad to the front seat cushion frame sub-assembly LH.


c.
B276735

Bend the 2 front seat cushion frame claws downward.


d.
B278201
1.792,2.583 1.656,2.583 1.656,2.583 1.542,3.167 false 1.813,2.5 2.24,2.823 0.427,0.323 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with new hog rings.


e.
B278178

for Front Passenger Side:

Attach the wire harness clamp.


f.
B278202
1.781,2.615 1.667,2.615 1.667,2.615 1.49,3.167 false 1.792,2.521 2.188,2.729 0.396,0.208 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the separate type front seat cushion cover to the front seat cushion frame sub-assembly LH with new hog rings.


Hide 12.INSTALL NO. 1 SEATBACK CLOTH (for RHD)

a.
B215906

Install the No. 1 seatback cloth to the separate type front seatback spring assembly.


Hide 13.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.
B207459

Install the separate type front seatback pad.


Hide 14.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



B286718
5.583,0.083 5.75,0.083 5.75,0.083 5.917,0.667 false 0.229,0.042 0.5,0.333 0.271,0.292 10 false *A 1.958,0.042 2.25,0.333 0.292,0.292 10 false *B 5.406,0.021 5.667,0.25 0.26,0.229 10 false *1 0.865,1.5 1.052,1.688 0.188,0.188 10 false *a 4.25,1.5 4.438,1.688 0.188,0.188 10 false *b 2.583,1.5 2.771,1.688 0.188,0.188 10 false *a
*A for Cloth Seat *B for Leather Seat
*1 Hog Ring Pliers - -
*a Front view of front seatback *b Rear view of front seatback



b.

Attach the 4 claws to install the 2 front seat headrest supports.


c.
B277651

Pass the straps of the separate type front seatback cover through the holes of the separate type front seatback pad.


d.
B209095
1.729,2.521 1.625,2.521 false 1.625,2.521 1.406,3.24 false 1.76,2.427 2.021,2.667 0.26,0.24 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the 2 straps of the separate type front seatback cover to the separate type front seatback spring assembly with new hog rings.


e.

Using hog ring pliers, attach the separate type front seatback cover with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




f.

Attach the 2 hooks.

B290353
5.917,0.646 5.802,0.646 5.802,0.646 5.802,1.208 false 4.438,0.302 4.323,0.302 4.323,0.302 3.927,0.615 true 1.104,0.188 1.01,0.188 1.01,0.188 0.698,0.49 true 3.083,1.583 2.896,0.813 true 3.083,1.583 2.24,0.802 true 3.083,1.583 1.49,0.844 true 5.969,0.563 6.24,0.792 0.271,0.229 10 false *1 4.479,0.219 4.844,0.438 0.365,0.219 10 false *3 1.167,0.104 1.469,0.302 0.302,0.198 10 false *3 3.135,1.531 3.479,1.729 0.344,0.198 10 false *2
*1 Hog Ring Pliers *2 Hog Ring
*3 Hook - -



g.

Install the front seatback assembly with the 4 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 15.INSTALL SEATBACK SPRING LH

a.
B277652

Install the seatback spring LH.


Hide 16.INSTALL FRONT SEAT CUSHION SHIELD LH

B278205
0.677,0.979 0.771,0.979 false 0.771,0.979 0.979,1.375 false 2.229,0.25 2.323,0.25 false 2.229,0.25 2.448,1.229 true 2.229,0.25 1.969,0.76 false 0.469,0.896 0.646,1.052 0.177,0.156 10 false *1 2.354,0.167 2.667,0.385 0.313,0.219 10 false *2 1.719,1.302 1.917,1.458 0.198,0.156 10 false (1) 2.729,1.323 2.927,1.479 0.198,0.156 10 false (2)
*1 Guide
*2 Hook


a.

Attach the guide and 2 hooks in the order shown in the illustration to install the front seat cushion shield LH.


b.

Install the 2 screws.


Hide 17.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

a.
B278206

Attach the claw to install the reclining adjuster release handle LH.


Hide 18.INSTALL VERTICAL SEAT ADJUSTER KNOB LH (for Driver Side)

B278207

a.

Install the snap ring to the vertical seat adjuster knob LH.


b.

Install the vertical seat adjuster knob LH.


Hide 19.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

B278208
1.749,0.911 1.974,1.092 0.225,0.181 10 (1) 0.834,1.212 1.059,1.392 0.225,0.181 10 (2)

a.

Attach the 2 hooks in the order shown in the illustration to install the front seat inner cushion shield LH.


b.

Install the 2 screws.


Hide 20.INSTALL FRONT SEAT CUSHION COVER LH

a.

Install the front seat cushion cover LH.


Hide 21.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

Hide 22.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)