Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Tumble Seat Type RH Side)
RM1880E _58 Vehicle Interior _013243 SEAT _0068645 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Tumble Seat Type RH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Tumble Seat Type RH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 1.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

B277482

a.

Tie the No. 1 fold seat stopper band assembly to the rear No. 1 seat cushion frame as shown in the illustration to install the No. 1 fold seat stopper band assembly.


Hide 4.INSTALL NO. 1 SEAT CUSHION PAD RH

B278285

a.

Pass the rear seat lap type belt assembly RH and rear center seat lap type belt assembly through the hole of the No. 1 seat cushion pad RH to the surface.


b.

Install the No. 1 seat cushion pad RH to the rear No. 1 seat cushion frame.


Hide 5.INSTALL REAR NO. 1 SEAT CUSHION COVER RH

B342784
4,0.917 3.917,0.667 3.917,0.667 3.833,0.667 false 2.063,2.125 2.167,1.094 2.167,1.094 2.417,1.094 false 3.656,0.594 4,0.833 0.344,0.24 10 false *1 2.458,1.01 2.833,1.25 0.375,0.24 10 false *2
*1 No. 1 Fold Seat Stopper Band Assembly *2 Hog Ring Pliers


a.

Pass the rear seat lap type belt assembly RH and rear center seat lap type belt assembly through the hole of the rear No. 1 seat cushion cover RH to the surface.


b.

Using hog ring pliers, install the rear No. 1 seat cushion cover RH to the No. 1 seat cushion pad RH with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




c.

Insert the No. 1 fold seat stopper band assembly into the rear No. 1 seat cushion cover RH.


d.
B279381
2.031,2.24 1.813,2.24 1.813,2.24 1.719,2.917 false 2.063,2.156 2.313,2.406 0.25,0.25 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install new hog rings.


e.
B279379
1.396,0.771 1.51,0.771 1.51,0.771 1.552,0.646 false 0.604,0.969 0.865,0.969 0.865,0.969 0.938,1.052 false 0.583,2.604 2.656,2.604 2.656,2.604 2.656,2.5 false 0.708,2.604 0.708,2.396 false 2.031,3.375 1.865,3.375 1.865,3.375 1.771,3.958 false 1.219,0.667 1.625,1.031 0.406,0.365 10 false *1 0.406,0.885 0.75,1.188 0.344,0.302 10 false *2 0.385,2.521 0.76,2.833 0.375,0.313 10 false *3 2.063,3.281 2.396,3.646 0.333,0.365 10 false *4
*1 Rear No. 1 Seat Cushion Cover RH Front Part
*2 Fastening Tape
*3 Fastener
*4 Hog Ring Pliers


Attach the 2 fasteners to close the rear No. 1 seat cushion cover RH.


f.

Using hog ring pliers, install new hog rings.


g.

Attach the fastening tape to close the front part of the rear No. 1 seat cushion cover RH.


Hide 6.INSTALL REAR SEAT TRACK ASSEMBLY RH

a.
B281388
3.292,2.115 3.375,2.115 false
V100135

MP Grease


Apply MP grease to the locations of the outer seat track assembly RH shown in the illustration.


b.
B281389
3.281,2.115 3.365,2.115 false
V100135

MP Grease


Apply MP grease to the locations of the inner seat track assembly RH shown in the illustration.


c.
B278641
3.271,2.104 3.354,2.104 false
V100135

MP Grease


Apply MP grease to the locations of the seat track adjusting handle shown in the illustration.


d.

If reusing the outer seat track assembly RH and inner seat track assembly RH:

i.
B279364

Using a T40 "TORX" socket wrench, temporarily install the front side of the outer seat track assembly RH with the "TORX" bolt.


ii.
B279366

Using a T40 "TORX" socket wrench, temporarily install the front side of the inner seat track assembly RH with the "TORX" bolt.


iii.

Insert the seat track adjusting handle into the outer seat track assembly RH and inner seat track assembly RH and engage the 2 seat track adjusting handle locks to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281392
5.667,0.51 5.042,0.51 5.042,0.51 4.927,0.74 false 5.594,0.51 5.594,0.74 false 5.51,1.271 5.115,1.271 5.115,1.271 4.948,0.979 true 5.406,1.271 5.406,1 true 6.271,0.573 6.385,0.573 6.385,0.573 6.49,0.969 false 1.615,1.26 2.021,1.26 2.021,1.26 2.167,0.979 true 1.719,1.26 1.719,1.01 true 0.865,0.594 0.75,0.594 0.75,0.594 0.635,0.99 false 1.469,0.51 2.052,0.51 2.052,0.51 2.219,0.74 false 1.531,0.51 1.531,0.74 false 5.688,0.427 5.979,0.677 0.292,0.25 10 false *1 5.563,1.188 5.844,1.417 0.281,0.229 10 false *3 6.125,0.5 6.427,0.802 0.302,0.302 10 false *2 1.438,1.177 1.698,1.438 0.26,0.26 10 false *3 0.875,0.51 1.156,0.781 0.281,0.271 10 false *2 1.313,0.427 1.604,0.688 0.292,0.26 10 false *4
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle *4 Outer Seat Track Assembly RH



iv.
B279360

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.


v.

Using a T40 "TORX" socket wrench, install the rear side of the outer seat track assembly RH and inner seat track assembly RH with the 4 "TORX" bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


vi.

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.

B279352
0.917,1.083 1.094,1.083 1.094,1.083 1.229,1.219 true 5.573,1.083 5.75,1.083 5.75,1.083 5.896,1.25 true 6.583,1.719 5.594,1.719 5.594,1.719 5.594,1.833 false 6.25,1.844 6.25,1.427 6.25,1.427 6.104,1.427 false 1.958,1.708 0.969,1.708 0.969,1.708 0.969,1.823 false 1.667,1.833 1.667,1.417 1.667,1.417 1.521,1.417 false 0.875,2.385 1.052,2.385 1.052,2.385 1.188,2.125 true 6.25,2.396 6.073,2.396 6.073,2.396 5.927,2.135 true 0.542,1.99 0.76,1.99 0.76,1.99 0.76,2.052 false 1.99,1.958 1.698,1.958 1.698,1.958 1.698,2 false 6.563,2.01 6.344,2.01 6.344,2.01 6.344,2.063 false 5.188,1.969 5.49,1.969 5.49,1.969 5.49,2.01 false 0.729,1.01 1.063,1.344 0.333,0.333 10 false *1 5.396,1.01 5.74,1.333 0.344,0.323 10 false *1 6.625,1.635 6.979,1.927 0.354,0.292 10 false *2 1.99,1.635 2.292,1.958 0.302,0.323 10 false *3 0.688,2.323 0.958,2.594 0.271,0.271 10 false *1 6.302,2.323 6.625,2.615 0.323,0.292 10 false *1 0.375,1.927 0.708,2.188 0.333,0.26 10 false *4 2.021,1.885 2.271,2.094 0.25,0.208 10 false *4 6.604,1.938 6.927,2.208 0.323,0.271 10 false *4 5.031,1.896 5.344,2.219 0.313,0.323 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



vii.

Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279354
2.667,0.646 2.813,0.646 2.813,0.646 3.104,1.094 false 4.167,0.927 4.656,0.927 4.656,0.927 4.938,1.229 false 4.313,0.927 4.313,1.229 false 4.948,1.865 4.948,1.667 4.948,1.667 4.76,1.563 true 5.865,1.823 6.354,1.823 6.354,1.823 6.635,1.521 true 6.01,1.823 6.01,1.49 true 2.51,0.573 2.854,0.854 0.344,0.281 10 false *1 4.021,0.833 4.406,1.115 0.385,0.281 10 false *2 4.875,1.896 5.208,2.24 0.333,0.344 10 false *3 5.667,1.729 5.979,2.063 0.313,0.333 10 false *4
*1 Screwdriver *2 Outer Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



viii.

Insert a screwdriver into the inner seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279356
4.448,0.948 4.333,0.948 4.333,0.948 4.104,1.396 false 2.948,1.167 2.458,1.167 2.458,1.167 2.177,1.469 false 2.802,1.167 2.802,1.469 false 2.75,2.104 2.75,1.906 2.75,1.906 2.563,1.813 true 1.271,2.083 0.781,2.083 0.781,2.083 0.5,1.719 true 1.115,2.083 1.115,1.75 true 4.479,0.875 4.781,1.177 0.302,0.302 10 false *1 2.99,1.083 3.302,1.406 0.313,0.323 10 false *2 2.688,2.135 3.073,2.375 0.385,0.24 10 false *3 1.323,2 1.688,2.323 0.365,0.323 10 false *4
*1 Screwdriver *2 Inner Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



ix.

Pull the seat track adjusting handle to the position shown in the illustration.

B281382
5.469,1.146 5.646,1.146 5.646,1.146 5.802,1.313 true 5.802,1.313 5.813,1.333 false 6.49,1.844 5.5,1.844 5.5,1.844 5.5,2.042 false 6.177,2.042 6.177,1.542 6.177,1.542 6.021,1.542 false 6.625,2.156 5.625,2.156 5.625,2.156 5.625,2.219 false 5.646,1.146 5.813,1.042 false 6.146,2.156 6.146,2.25 false 6.719,3.052 5.594,3.052 5.594,3.052 5.594,3.115 false 6.104,3.052 6.104,3.146 false 0.823,1.135 1.01,1.135 1.01,1.135 1.156,1.302 true 0.563,1.844 1.552,1.844 1.552,1.844 1.552,2.042 false 1.01,1.542 0.865,1.542 0.865,1.542 0.865,2.042 false 0.531,2.156 1.521,2.156 1.521,2.156 1.521,2.219 false 1.01,1.135 1.167,1.031 false 1.01,2.156 1.01,2.25 false 0.438,3.052 1.563,3.052 1.563,3.052 1.563,3.115 false 1.042,3.052 1.042,3.146 false 5.302,1.083 5.719,1.417 0.417,0.333 10 false *1 6.521,1.76 6.813,2.01 0.292,0.25 10 false *2 6.677,2.094 6.948,2.365 0.271,0.271 10 false *4 6.771,2.99 7.135,3.313 0.365,0.323 10 false *4 0.667,1.073 1.052,1.469 0.385,0.396 10 false *1 0.385,1.76 0.656,2.042 0.271,0.281 10 false *3 0.375,2.094 0.719,2.375 0.344,0.281 10 false *4 0.292,2.99 0.656,3.292 0.365,0.302 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



x.
B281383

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the rearmost position.

NOTICE:

At this time, do not engage the lock of the seat track adjusting handle.



xi.
B281384

Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.


xii.
B281393

Using a T40 "TORX" socket wrench, tighten the 2 "TORX" bolts on the front side of the outer seat track assembly RH and inner seat track assembly RH.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


xiii.

Insert the seat track adjusting handle into the outer seat track assembly RH and inner seat track assembly RH and engage the 2 seat track adjusting handle locks to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281392
5.667,0.51 5.042,0.51 5.042,0.51 4.927,0.74 false 5.594,0.51 5.594,0.74 false 5.51,1.271 5.115,1.271 5.115,1.271 4.948,0.979 true 5.406,1.271 5.406,1 true 6.271,0.573 6.385,0.573 6.385,0.573 6.49,0.969 false 1.615,1.26 2.021,1.26 2.021,1.26 2.167,0.979 true 1.719,1.26 1.719,1.01 true 0.865,0.594 0.75,0.594 0.75,0.594 0.635,0.99 false 1.469,0.51 2.052,0.51 2.052,0.51 2.219,0.74 false 1.531,0.51 1.531,0.74 false 5.688,0.427 5.979,0.677 0.292,0.25 10 false *1 5.563,1.188 5.844,1.417 0.281,0.229 10 false *3 6.125,0.5 6.427,0.802 0.302,0.302 10 false *2 1.438,1.177 1.698,1.438 0.26,0.26 10 false *3 0.875,0.51 1.156,0.781 0.281,0.271 10 false *2 1.313,0.427 1.604,0.688 0.292,0.26 10 false *4
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle *4 Outer Seat Track Assembly RH




e.

If replacing the outer seat track assembly RH with a new one but reusing the inner seat track assembly RH:

i.
B281401

Using a T40 "TORX" socket wrench, temporarily install the rear side of a new outer seat track assembly RH with the 2 "TORX" bolts.


ii.
B279366

Using a T40 "TORX" socket wrench, temporarily install the front side of the inner seat track assembly RH with the "TORX" bolt.


iii.

Insert the seat track adjusting handle into the outer seat track assembly RH and engage the seat track adjusting handle lock to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281402
2.333,1.625 2.833,1.625 2.833,1.625 3.031,1.344 true 2.469,1.625 2.469,1.375 true 1.625,0.948 1.51,0.948 1.51,0.948 1.406,1.365 false 2.458,0.896 2.865,0.896 2.865,0.896 2.99,1.115 false 2.521,0.896 2.521,1.115 false 2.146,1.552 2.469,1.844 0.323,0.292 10 false *3 1.667,0.844 1.969,1.125 0.302,0.281 10 false *2 2.271,0.813 2.625,1.208 0.354,0.396 10 false *1
*1 Outer Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle - -



iv.

Operate the seat track adjusting handle and, while moving the outer seat track assembly RH toward the rearmost position, insert the handle into the inner seat track assembly RH and engage the lock of the seat track adjusting handle to install the handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281403
4.604,1.198 3.979,1.198 3.979,1.198 3.854,1.417 false 4.531,1.198 4.531,1.417 false 4.385,1.948 3.99,1.948 3.99,1.948 3.813,1.646 true 4.271,1.948 4.271,1.677 true 5.208,1.25 5.313,1.25 5.313,1.25 5.427,1.646 false 4.625,1.115 4.917,1.406 0.292,0.292 10 false *1 4.417,1.854 4.802,2.125 0.385,0.271 10 false *3 5.031,1.177 5.313,1.469 0.281,0.292 10 false *2
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle - -



v.
B281412

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.


vi.

Using a T40 "TORX" socket wrench, install the rear side of the inner seat track assembly RH with the 2 "TORX" bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


vii.

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.

B279352
0.917,1.083 1.094,1.083 1.094,1.083 1.229,1.219 true 5.573,1.083 5.75,1.083 5.75,1.083 5.896,1.25 true 6.583,1.719 5.594,1.719 5.594,1.719 5.594,1.833 false 6.25,1.844 6.25,1.427 6.25,1.427 6.104,1.427 false 1.958,1.708 0.969,1.708 0.969,1.708 0.969,1.823 false 1.667,1.833 1.667,1.417 1.667,1.417 1.521,1.417 false 0.875,2.385 1.052,2.385 1.052,2.385 1.188,2.125 true 6.25,2.396 6.073,2.396 6.073,2.396 5.927,2.135 true 0.542,1.99 0.76,1.99 0.76,1.99 0.76,2.052 false 1.99,1.958 1.698,1.958 1.698,1.958 1.698,2 false 6.563,2.01 6.344,2.01 6.344,2.01 6.344,2.063 false 5.188,1.969 5.49,1.969 5.49,1.969 5.49,2.01 false 0.729,1.01 1.063,1.344 0.333,0.333 10 false *1 5.396,1.01 5.74,1.333 0.344,0.323 10 false *1 6.604,1.635 6.958,1.927 0.354,0.292 10 false *2 1.99,1.635 2.292,1.958 0.302,0.323 10 false *3 0.688,2.323 0.958,2.594 0.271,0.271 10 false *1 6.302,2.323 6.625,2.615 0.323,0.292 10 false *1 0.375,1.927 0.708,2.188 0.333,0.26 10 false *4 2.021,1.885 2.271,2.094 0.25,0.208 10 false *4 6.573,1.938 6.896,2.208 0.323,0.271 10 false *4 5.031,1.896 5.344,2.219 0.313,0.323 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



viii.

Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279354
2.667,0.646 2.813,0.646 2.813,0.646 3.104,1.094 false 4.167,0.927 4.656,0.927 4.656,0.927 4.938,1.229 false 4.313,0.927 4.313,1.229 false 4.948,1.865 4.948,1.667 4.948,1.667 4.76,1.563 true 5.865,1.823 6.354,1.823 6.354,1.823 6.635,1.521 true 6.01,1.823 6.01,1.49 true 2.51,0.573 2.854,0.854 0.344,0.281 10 false *1 4,0.854 4.385,1.135 0.385,0.281 10 false *2 4.875,1.896 5.208,2.24 0.333,0.344 10 false *3 5.677,1.76 5.99,2.094 0.313,0.333 10 false *4
*1 Screwdriver *2 Outer Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



ix.

Insert a screwdriver into the inner seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279356
4.448,0.948 4.333,0.948 4.333,0.948 4.104,1.396 false 2.948,1.167 2.458,1.167 2.458,1.167 2.177,1.469 false 2.802,1.167 2.802,1.469 false 2.75,2.104 2.75,1.906 2.75,1.906 2.563,1.813 true 1.271,2.083 0.781,2.083 0.781,2.083 0.5,1.719 true 1.115,2.083 1.115,1.75 true 4.479,0.875 4.781,1.177 0.302,0.302 10 false *1 2.99,1.083 3.302,1.406 0.313,0.323 10 false *2 2.688,2.135 3.073,2.375 0.385,0.24 10 false *3 1.323,2 1.688,2.323 0.365,0.323 10 false *4
*1 Screwdriver *2 Inner Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



x.

Pull the seat track adjusting handle to the position shown in the illustration.

B281382
5.469,1.146 5.646,1.146 5.646,1.146 5.802,1.313 true 5.802,1.313 5.813,1.333 false 6.49,1.844 5.5,1.844 5.5,1.844 5.5,2.042 false 6.177,2.042 6.177,1.542 6.177,1.542 6.021,1.542 false 6.625,2.156 5.625,2.156 5.625,2.156 5.625,2.219 false 5.646,1.146 5.813,1.042 false 6.146,2.156 6.146,2.25 false 6.719,3.052 5.594,3.052 5.594,3.052 5.594,3.115 false 6.104,3.052 6.104,3.146 false 0.823,1.135 1.01,1.135 1.01,1.135 1.156,1.302 true 0.563,1.844 1.552,1.844 1.552,1.844 1.552,2.042 false 1.01,1.542 0.865,1.542 0.865,1.542 0.865,2.042 false 0.531,2.156 1.521,2.156 1.521,2.156 1.521,2.219 false 1.01,1.135 1.167,1.031 false 1.01,2.156 1.01,2.25 false 0.438,3.052 1.563,3.052 1.563,3.052 1.563,3.115 false 1.042,3.052 1.042,3.146 false 5.302,1.083 5.719,1.417 0.417,0.333 10 false *1 6.521,1.76 6.813,2.01 0.292,0.25 10 false *2 6.646,2.094 6.917,2.365 0.271,0.271 10 false *4 6.75,2.99 7.115,3.313 0.365,0.323 10 false *4 0.667,1.073 1.052,1.469 0.385,0.396 10 false *1 0.385,1.76 0.656,2.042 0.271,0.281 10 false *3 0.375,2.094 0.719,2.375 0.344,0.281 10 false *4 0.292,2.99 0.656,3.292 0.365,0.302 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



xi.
B281383

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the rearmost position.

NOTICE:

At this time, do not engage the lock of the seat track adjusting handle.



xii.
B281384

Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.


xiii.
B279364

Using a T40 "TORX" socket wrench, install the front side of the outer seat track assembly RH with the "TORX" bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


xiv.
B281413

Using a T40 "TORX" socket wrench, tighten the "TORX" bolt on the front side of the inner seat track assembly RH.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


xv.

Insert the seat track adjusting handle into the outer seat track assembly RH and inner seat track assembly RH and engage the 2 seat track adjusting handle locks and install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281392
5.667,0.51 5.042,0.51 5.042,0.51 4.927,0.74 false 5.594,0.51 5.594,0.74 false 5.51,1.271 5.115,1.271 5.115,1.271 4.948,0.979 true 5.406,1.271 5.406,1 true 6.271,0.573 6.385,0.573 6.385,0.573 6.49,0.969 false 1.615,1.26 2.021,1.26 2.021,1.26 2.167,0.979 true 1.719,1.26 1.719,1.01 true 0.865,0.594 0.75,0.594 0.75,0.594 0.635,0.99 false 1.469,0.51 2.052,0.51 2.052,0.51 2.219,0.74 false 1.531,0.51 1.531,0.74 false 5.698,0.427 5.99,0.677 0.292,0.25 10 false *1 5.563,1.188 5.844,1.417 0.281,0.229 10 false *3 6.125,0.5 6.427,0.802 0.302,0.302 10 false *2 1.438,1.177 1.698,1.438 0.26,0.26 10 false *3 0.896,0.531 1.177,0.802 0.281,0.271 10 false *2 1.313,0.427 1.604,0.688 0.292,0.26 10 false *4
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle *4 Outer Seat Track Assembly RH



xvi.
B281414

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.


xvii.

Using a T40 "TORX" socket wrench, tighten the 2 "TORX" bolts on the rear side of the outer seat track assembly RH.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



f.

If replacing the inner seat track assembly RH with a new one but reusing the outer seat track assembly RH:

i.
B281415

Using a T40 "TORX" socket wrench, temporarily install the rear side of a new inner seat track assembly RH with the 2 "TORX" bolts.


ii.
B279364

Using a T40 "TORX" socket wrench, temporarily install the front side of the outer seat track assembly RH with the "TORX" bolt.


iii.

Insert the seat track adjusting handle into the inner seat track assembly RH and engage the seat track adjusting handle lock to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281417
4.667,0.875 4.052,0.875 4.052,0.875 3.927,1.104 false 4.51,0.875 4.51,1.104 false 4.458,1.604 4.063,1.604 4.063,1.604 3.906,1.302 true 4.354,1.604 4.354,1.344 true 5.292,0.938 5.406,0.938 5.406,0.938 5.521,1.333 false 4.688,0.792 5,1.052 0.313,0.26 10 false *1 4.521,1.531 5.167,1.938 0.646,0.406 10 false *3 5.104,0.844 5.417,1.198 0.313,0.354 10 false *2
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle - -



iv.

Operate the seat track adjusting handle and, while moving the inner seat track assembly RH toward the rearmost position, insert the handle into the outer seat track assembly RH and engage the lock of the seat track adjusting handle to install the handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281418
2.198,1.917 2.698,1.917 2.698,1.917 2.885,1.646 true 2.323,1.917 2.323,1.667 true 1.438,1.24 1.323,1.24 1.323,1.24 1.219,1.656 false 2.271,1.188 2.677,1.188 2.677,1.188 2.792,1.417 false 2.333,1.188 2.333,1.417 false 2.01,1.833 2.292,2.115 0.281,0.281 10 false *3 1.448,1.135 1.771,1.438 0.323,0.302 10 false *2 2.094,1.104 2.344,1.365 0.25,0.26 10 false *1
*1 Outer Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle - -



v.
B281422

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.


vi.

Using a T40 "TORX" socket wrench, install the rear side of the outer seat track assembly RH with the 2 "TORX" bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


vii.

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.

B279352
0.917,1.083 1.094,1.083 1.094,1.083 1.229,1.219 true 5.573,1.083 5.75,1.083 5.75,1.083 5.896,1.25 true 6.583,1.719 5.594,1.719 5.594,1.719 5.594,1.833 false 6.25,1.844 6.25,1.427 6.25,1.427 6.104,1.427 false 1.958,1.708 0.969,1.708 0.969,1.708 0.969,1.823 false 1.667,1.833 1.667,1.417 1.667,1.417 1.521,1.417 false 0.875,2.385 1.052,2.385 1.052,2.385 1.188,2.125 true 6.25,2.396 6.073,2.396 6.073,2.396 5.927,2.135 true 0.542,1.99 0.76,1.99 0.76,1.99 0.76,2.052 false 1.99,1.958 1.698,1.958 1.698,1.958 1.698,2 false 6.563,2.01 6.344,2.01 6.344,2.01 6.344,2.063 false 5.188,1.969 5.49,1.969 5.49,1.969 5.49,2.01 false 0.729,1.01 1.063,1.344 0.333,0.333 10 false *1 5.396,1.01 5.74,1.333 0.344,0.323 10 false *1 6.604,1.635 6.958,1.927 0.354,0.292 10 false *2 1.99,1.635 2.292,1.958 0.302,0.323 10 false *3 0.688,2.323 0.958,2.594 0.271,0.271 10 false *1 6.302,2.323 6.625,2.615 0.323,0.292 10 false *1 0.375,1.927 0.708,2.188 0.333,0.26 10 false *4 2.021,1.885 2.271,2.094 0.25,0.208 10 false *4 6.594,1.938 6.917,2.208 0.323,0.271 10 false *4 5.031,1.896 5.344,2.219 0.313,0.323 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



viii.

Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279354
2.667,0.646 2.813,0.646 2.813,0.646 3.104,1.094 false 4.167,0.927 4.656,0.927 4.656,0.927 4.938,1.229 false 4.313,0.927 4.313,1.229 false 4.948,1.865 4.948,1.667 4.948,1.667 4.76,1.563 true 5.865,1.823 6.354,1.823 6.354,1.823 6.635,1.521 true 6.01,1.823 6.01,1.49 true 2.51,0.573 2.854,0.854 0.344,0.281 10 false *1 3.99,0.854 4.375,1.135 0.385,0.281 10 false *2 4.875,1.896 5.208,2.24 0.333,0.344 10 false *3 5.667,1.729 5.979,2.063 0.313,0.333 10 false *4
*1 Screwdriver *2 Outer Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



ix.

Insert a screwdriver into the inner seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279356
4.448,0.948 4.333,0.948 4.333,0.948 4.104,1.396 false 2.948,1.167 2.458,1.167 2.458,1.167 2.177,1.469 false 2.802,1.167 2.802,1.469 false 2.75,2.104 2.75,1.906 2.75,1.906 2.563,1.813 true 1.271,2.083 0.781,2.083 0.781,2.083 0.5,1.719 true 1.115,2.083 1.115,1.75 true 4.479,0.875 4.781,1.177 0.302,0.302 10 false *1 2.99,1.083 3.302,1.406 0.313,0.323 10 false *2 2.688,2.135 3.073,2.375 0.385,0.24 10 false *3 1.323,2 1.688,2.323 0.365,0.323 10 false *4
*1 Screwdriver *2 Inner Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



x.

Pull the seat track adjusting handle to the position shown in the illustration.

B281382
5.469,1.146 5.646,1.146 5.646,1.146 5.802,1.313 true 5.802,1.313 5.813,1.333 false 6.49,1.844 5.5,1.844 5.5,1.844 5.5,2.042 false 6.177,2.042 6.177,1.542 6.177,1.542 6.021,1.542 false 6.625,2.156 5.625,2.156 5.625,2.156 5.625,2.219 false 5.646,1.146 5.813,1.042 false 6.146,2.156 6.146,2.25 false 6.719,3.052 5.594,3.052 5.594,3.052 5.594,3.115 false 6.104,3.052 6.104,3.146 false 0.823,1.135 1.01,1.135 1.01,1.135 1.156,1.302 true 0.563,1.844 1.552,1.844 1.552,1.844 1.552,2.042 false 1.01,1.542 0.865,1.542 0.865,1.542 0.865,2.042 false 0.531,2.156 1.521,2.156 1.521,2.156 1.521,2.219 false 1.01,1.135 1.167,1.031 false 1.01,2.156 1.01,2.25 false 0.438,3.052 1.563,3.052 1.563,3.052 1.563,3.115 false 1.042,3.052 1.042,3.146 false 5.302,1.083 5.719,1.417 0.417,0.333 10 false *1 6.521,1.76 6.813,2.01 0.292,0.25 10 false *2 6.646,2.094 6.917,2.365 0.271,0.271 10 false *4 6.75,2.99 7.115,3.313 0.365,0.323 10 false *4 0.667,1.073 1.052,1.469 0.385,0.396 10 false *1 0.385,1.76 0.656,2.042 0.271,0.281 10 false *3 0.375,2.094 0.719,2.375 0.344,0.281 10 false *4 0.292,2.99 0.656,3.292 0.365,0.302 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



xi.
B281383

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the rearmost position.

NOTICE:

At this time, do not engage the lock of the seat track adjusting handle.



xii.
B281384

Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.


xiii.
B279366

Using a T40 "TORX" socket wrench, install the front side of the inner seat track assembly RH with the "TORX" bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


xiv.
B281423

Using a T40 "TORX" socket wrench, tighten the "TORX" bolt on the front side of the outer seat track assembly RH.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


xv.

Insert the seat track adjusting handle into the outer seat track assembly RH and inner seat track assembly RH and engage the 2 seat track adjusting handle locks to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281392
5.667,0.51 5.042,0.51 5.042,0.51 4.927,0.74 false 5.594,0.51 5.594,0.74 false 5.51,1.271 5.115,1.271 5.115,1.271 4.948,0.979 true 5.406,1.271 5.406,1 true 6.271,0.573 6.385,0.573 6.385,0.573 6.49,0.969 false 1.615,1.26 2.021,1.26 2.021,1.26 2.167,0.979 true 1.719,1.26 1.719,1.01 true 0.865,0.594 0.75,0.594 0.75,0.594 0.635,0.99 false 1.469,0.51 2.052,0.51 2.052,0.51 2.219,0.74 false 1.531,0.51 1.531,0.74 false 5.688,0.427 5.979,0.677 0.292,0.25 10 false *1 5.563,1.188 5.844,1.417 0.281,0.229 10 false *3 6.125,0.5 6.427,0.802 0.302,0.302 10 false *2 1.438,1.177 1.698,1.438 0.26,0.26 10 false *3 0.875,0.51 1.156,0.781 0.281,0.271 10 false *2 1.313,0.427 1.604,0.688 0.292,0.26 10 false *4
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle *4 Outer Seat Track Assembly RH



xvi.
B281424

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.


xvii.

Using a T40 "TORX" socket wrench, tighten the 2 "TORX" bolts on the rear side of the inner seat track assembly RH.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



g.

If replacing both the outer seat track assembly RH and inner seat track assembly RH with new ones:

i.
B281401

Using a T40 "TORX" socket wrench, temporarily install the rear side of a new outer seat track assembly RH with the 2 "TORX" bolts.


ii.
B281415

Using a T40 "TORX" socket wrench, temporarily install the rear side of a new inner seat track assembly RH with the 2 "TORX" bolts.


iii.

Insert the seat track adjusting handle into the outer seat track assembly RH and inner seat track assembly RH and engage the 2 seat track adjusting handle locks to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281430
5.677,0.396 5.052,0.396 5.052,0.396 4.927,0.604 false 5.604,0.396 5.604,0.604 false 5.51,1.083 5.115,1.083 5.115,1.083 4.938,0.813 true 5.417,1.083 5.417,0.833 true 6.281,0.438 6.385,0.438 6.385,0.438 6.5,0.833 false 1.604,1.104 2.01,1.104 2.01,1.104 2.177,0.833 true 1.708,1.104 1.708,0.844 true 0.813,0.427 0.698,0.427 0.698,0.427 0.583,0.823 false 1.5,0.385 2.083,0.385 2.083,0.385 2.25,0.615 false 1.563,0.385 1.563,0.615 false 5.708,0.302 5.958,0.542 0.25,0.24 10 false *1 5.542,0.99 5.885,1.229 0.344,0.24 10 false *3 6.104,0.354 6.344,0.646 0.24,0.292 10 false *2 1.417,1.01 1.844,1.292 0.427,0.281 10 false *3 0.833,0.333 1.104,0.594 0.271,0.26 10 false *2 1.313,0.302 1.615,0.615 0.302,0.313 10 false *4
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle *4 Outer Seat Track Assembly RH



iv.

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.

B279352
0.917,1.083 1.094,1.083 1.094,1.083 1.229,1.219 true 5.573,1.083 5.75,1.083 5.75,1.083 5.896,1.25 true 6.583,1.719 5.594,1.719 5.594,1.719 5.594,1.833 false 6.25,1.844 6.25,1.427 6.25,1.427 6.104,1.427 false 1.958,1.708 0.969,1.708 0.969,1.708 0.969,1.823 false 1.667,1.833 1.667,1.417 1.667,1.417 1.521,1.417 false 0.875,2.385 1.052,2.385 1.052,2.385 1.188,2.125 true 6.25,2.396 6.073,2.396 6.073,2.396 5.927,2.135 true 0.542,1.99 0.76,1.99 0.76,1.99 0.76,2.052 false 1.99,1.958 1.698,1.958 1.698,1.958 1.698,2 false 6.563,2.01 6.344,2.01 6.344,2.01 6.344,2.063 false 5.188,1.969 5.49,1.969 5.49,1.969 5.49,2.01 false 0.729,1.01 1.063,1.344 0.333,0.333 10 false *1 5.396,1.01 5.74,1.333 0.344,0.323 10 false *1 6.625,1.635 6.979,1.927 0.354,0.292 10 false *2 1.99,1.635 2.292,1.958 0.302,0.323 10 false *3 0.688,2.323 0.958,2.594 0.271,0.271 10 false *1 6.302,2.323 6.625,2.615 0.323,0.292 10 false *1 0.375,1.927 0.708,2.188 0.333,0.26 10 false *4 2.021,1.885 2.271,2.094 0.25,0.208 10 false *4 6.615,1.938 6.938,2.208 0.323,0.271 10 false *4 5.031,1.896 5.344,2.219 0.313,0.323 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



v.

Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279354
2.667,0.646 2.813,0.646 2.813,0.646 3.104,1.094 false 4.167,0.927 4.656,0.927 4.656,0.927 4.938,1.229 false 4.313,0.927 4.313,1.229 false 4.948,1.865 4.948,1.667 4.948,1.667 4.76,1.563 true 5.865,1.823 6.354,1.823 6.354,1.823 6.635,1.521 true 6.01,1.823 6.01,1.49 true 2.5,0.573 2.844,0.854 0.344,0.281 10 false *1 3.99,0.833 4.375,1.115 0.385,0.281 10 false *2 4.875,1.896 5.208,2.24 0.333,0.344 10 false *3 5.667,1.729 5.979,2.063 0.313,0.333 10 false *4
*1 Screwdriver *2 Outer Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



vi.

Insert a screwdriver into the inner seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.

NOTICE:

Do not use excessive force to pull out the seat track adjusting handle.


B279356
4.448,0.948 4.333,0.948 4.333,0.948 4.104,1.396 false 2.948,1.167 2.458,1.167 2.458,1.167 2.177,1.469 false 2.802,1.167 2.802,1.469 false 2.75,2.104 2.75,1.906 2.75,1.906 2.563,1.813 true 1.271,2.083 0.781,2.083 0.781,2.083 0.5,1.719 true 1.115,2.083 1.115,1.75 true 4.479,0.875 4.781,1.177 0.302,0.302 10 false *1 2.99,1.083 3.302,1.406 0.313,0.323 10 false *2 2.688,2.135 3.073,2.375 0.385,0.24 10 false *3 1.323,2 1.688,2.323 0.365,0.323 10 false *4
*1 Screwdriver *2 Inner Seat Track Assembly RH
*3 Seat Track Adjusting Handle Lock *4 Seat Track Adjusting Handle



vii.

Pull the seat track adjusting handle to the position shown in the illustration.

B281382
5.469,1.146 5.646,1.146 5.646,1.146 5.802,1.313 true 5.802,1.313 5.813,1.333 false 6.49,1.844 5.5,1.844 5.5,1.844 5.5,2.042 false 6.177,2.042 6.177,1.542 6.177,1.542 6.021,1.542 false 6.625,2.156 5.625,2.156 5.625,2.156 5.625,2.219 false 5.646,1.146 5.813,1.042 false 6.146,2.156 6.146,2.25 false 6.719,3.052 5.594,3.052 5.594,3.052 5.594,3.115 false 6.104,3.052 6.104,3.146 false 0.823,1.135 1.01,1.135 1.01,1.135 1.156,1.302 true 0.563,1.844 1.552,1.844 1.552,1.844 1.552,2.042 false 1.01,1.542 0.865,1.542 0.865,1.542 0.865,2.042 false 0.531,2.156 1.521,2.156 1.521,2.156 1.521,2.219 false 1.01,1.135 1.167,1.031 false 1.01,2.156 1.01,2.25 false 0.438,3.052 1.563,3.052 1.563,3.052 1.563,3.115 false 1.042,3.052 1.042,3.146 false 5.302,1.083 5.719,1.417 0.417,0.333 10 false *1 6.552,1.76 6.844,2.01 0.292,0.25 10 false *2 6.677,2.083 6.948,2.354 0.271,0.271 10 false *4 6.771,2.99 7.135,3.313 0.365,0.323 10 false *4 0.667,1.073 1.052,1.469 0.385,0.396 10 false *1 0.385,1.76 0.656,2.042 0.271,0.281 10 false *3 0.375,2.094 0.719,2.375 0.344,0.281 10 false *4 0.292,2.99 0.656,3.292 0.365,0.302 10 false *4
*1 Seat Track Adjusting Handle Lock *2 Inner Seat Track Assembly RH
*3 Outer Seat Track Assembly RH *4 Seat Track Adjusting Handle



viii.
B281383

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the rearmost position.

NOTICE:

At this time, do not engage the lock of the seat track adjusting handle.



ix.
B281384

Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.


x.
B281431

Using a T40 "TORX" socket wrench, install the front side of the outer seat track assembly RH and inner seat track assembly RH with the 2 "TORX" bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


xi.

Insert the seat track adjusting handle into the outer seat track assembly RH and inner seat track assembly RH and engage the 2 seat track adjusting handle locks to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281392
5.667,0.51 5.042,0.51 5.042,0.51 4.927,0.74 false 5.594,0.51 5.594,0.74 false 5.51,1.271 5.115,1.271 5.115,1.271 4.948,0.979 true 5.406,1.271 5.406,1 true 6.271,0.573 6.385,0.573 6.385,0.573 6.49,0.969 false 1.615,1.26 2.021,1.26 2.021,1.26 2.167,0.979 true 1.719,1.26 1.719,1.01 true 0.865,0.594 0.75,0.594 0.75,0.594 0.635,0.99 false 1.469,0.51 2.052,0.51 2.052,0.51 2.219,0.74 false 1.531,0.51 1.531,0.74 false 5.688,0.427 5.979,0.677 0.292,0.25 10 false *1 5.563,1.188 5.844,1.417 0.281,0.229 10 false *3 6.125,0.5 6.427,0.802 0.302,0.302 10 false *2 1.438,1.177 1.698,1.438 0.26,0.26 10 false *3 0.906,0.51 1.188,0.781 0.281,0.271 10 false *2 1.313,0.427 1.604,0.688 0.292,0.26 10 false *4
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle *4 Outer Seat Track Assembly RH



xii.
B281432

Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.


xiii.

Using a T40 "TORX" socket wrench, tighten the 4 "TORX" bolts on the rear side of the outer seat track assembly RH and inner seat track assembly RH.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



Hide 7.INSTALL SEAT TRACK ADJUSTING HANDLE

HINT:

Perform this procedure when removing and reinstalling or replacing only the seat track adjusting handle.


a.
B278641
3.271,2.104 3.354,2.104 false
V100135

MP Grease


Apply MP grease to the locations shown in the illustration.


b.

Push the seat track adjusting handle into the outer seat track assembly RH and inner seat track assembly RH and engage the 2 seat track adjusting handle locks to install the seat track adjusting handle.

NOTICE:

Make sure the handle is straight when installing it, and check that it is centered.


B281430
5.677,0.396 5.052,0.396 5.052,0.396 4.927,0.604 false 5.604,0.396 5.604,0.604 false 5.51,1.083 5.115,1.083 5.115,1.083 4.938,0.813 true 5.417,1.083 5.417,0.833 true 6.281,0.438 6.385,0.438 6.385,0.438 6.5,0.833 false 1.604,1.104 2.01,1.104 2.01,1.104 2.177,0.833 true 1.708,1.104 1.708,0.844 true 0.813,0.427 0.698,0.427 0.698,0.427 0.583,0.823 false 1.5,0.385 2.083,0.385 2.083,0.385 2.25,0.615 false 1.563,0.385 1.563,0.615 false 5.708,0.302 5.958,0.542 0.25,0.24 10 false *1 5.542,0.99 5.885,1.229 0.344,0.24 10 false *3 6.104,0.354 6.344,0.646 0.24,0.292 10 false *2 1.417,1.01 1.844,1.292 0.427,0.281 10 false *3 0.833,0.333 1.104,0.594 0.271,0.26 10 false *2 1.313,0.302 1.615,0.615 0.302,0.313 10 false *4
*1 Inner Seat Track Assembly RH *2 Seat Track Adjusting Handle Lock
*3 Seat Track Adjusting Handle *4 Outer Seat Track Assembly RH



Hide 8.INSTALL REAR SEAT LOCK ASSEMBLY RH

a.

Install the washer to the outer seat track assembly RH.


b.
B281385
2.271,1.813 2.083,1.813 2.083,1.813 1.958,1.531 false 2.302,1.74 2.656,2.094 0.354,0.354 10 false *1
*1 Rear Seat Lock Link


Connect the rear seat lock link to the outer seat track assembly RH with the washer and a new E-ring.


c.

Install the rear seat lock assembly RH to the outer seat track assembly RH with the 2 nuts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 9.INSTALL REAR SEAT CUSHION SUPPORT SPRING

a.

Using needle nose pliers, install the rear seat cushion support spring.


Hide 10.INSTALL REAR SEAT LOCK ASSEMBLY LH

B281386
3.281,2.115 3.365,2.115 false
V100135

MP Grease


a.

Apply MP grease to the locations of the rear seat lock assembly LH and "TORX" bolt shown in the illustration.


b.

Using a T40 "TORX" socket wrench, install the rear seat lock assembly LH to the inner seat track assembly RH with the "TORX" bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 11.INSTALL REAR SEAT NO. 1 CUSHION SUPPORT SPRING

a.

Using needle nose pliers, install the rear seat No. 1 cushion support spring.


Hide 12.INSTALL REAR SEAT LOCK CONTROL CABLE RH

B279336
2.458,0.573 2.271,0.573 false 2.427,1.01 2.229,1.01 false 3.021,2.781 2.875,2.781 2.875,2.781 2.667,3.063 true 1.521,4.094 1.521,3.958 1.521,3.958 1.417,3.906 false 3.073,4.354 2.896,4.354 2.896,4.354 2.771,4.281 false 2.479,0.49 2.781,0.813 0.302,0.323 10 false *1 2.458,0.927 2.75,1.167 0.292,0.24 10 false *2 3.031,2.688 3.323,3.073 0.292,0.385 10 false *3 1.438,4.094 1.719,4.396 0.281,0.302 10 false *4 3.094,4.281 3.344,4.573 0.25,0.292 10 false *4
*1 Fastening Tape
*2 Rear No. 1 Seat Cushion Cover RH Lower Part
*3 Cable End
*4 Cable Clamp


a.

Insert the cable end and twist it in the direction indicated by the arrow to connect the rear seat lock control cable RH to the rear seat lock assembly LH.


b.

Attach the cable clamp.


c.

Install the washer and connect the rear seat lock control cable RH to the rear seat lock assembly RH.


d.

Install the washer and a new E-ring to the rear seat lock assembly RH.


e.

Attach the cable clamp to install the rear seat lock control cable RH.


f.

Attach the fastening tape to close the lower part of the rear No. 1 seat cushion cover RH.


Hide 13.INSTALL REAR SEAT HINGE ASSEMBLY LH

a.

Install the rear seat hinge assembly LH to the inner seat track assembly RH with the 2 nuts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 14.INSTALL REAR SEAT HINGE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 15.INSTALL NO. 1 SEAT LEG LINK

a.

Install the 2 washers to the rear seat hinge assembly LH and rear seat lock assembly LH.


b.

Install the No. 1 seat leg link with the 2 washers and 2 new E-rings to the rear seat hinge assembly LH and rear seat lock assembly LH.


Hide 16.INSTALL LOWER SEAT TRACK RAIL PROTECTOR LH

a.

Attach the 2 claws to install the lower seat track rail protector LH to the inner seat track assembly RH.


b.

Install the screw.


Hide 17.INSTALL LOWER SEAT TRACK RAIL PROTECTOR RH

a.

Attach the 4 claws to install the lower seat track rail protector RH to the outer seat track assembly RH.


Hide 18.INSTALL REAR SEAT INNER LOCK COVER RH

a.

Attach the guide and claw to install the rear seat inner lock cover RH to the rear seat lock assembly LH.


Hide 19.INSTALL REAR SEAT OUTER LOCK COVER RH

a.

Attach the 2 claws to install the rear seat outer lock cover RH.


b.

Install the screw.


Hide 20.INSTALL REAR PROTECTOR PIPE

B281387
3.302,2.115 3.385,2.115 false
V100135

MP Grease


a.

Apply MP grease to the locations shown in the illustration.


b.

Install the 2 rear protector pipes.


Hide 21.INSTALL RECLINING RELEASE HANDLE SUB-ASSEMBLY

B279328

a.

Install the reclining release handle sub-assembly as shown in the illustration.


Hide 22.INSTALL REAR SEAT LOCK COVER RH

B279318
1.146,2.01 0.948,2.01 0.948,2.01 0.833,1.771 false 1.167,1.917 1.635,2.156 0.469,0.24 10 false *1
*1 Reclining Release Handle Sub-assembly


a.

Pass the reclining release handle sub-assembly through the hole of the rear seat lock cover RH.


b.

Install the rear seat lock cover RH with the 2 screws.


Hide 23.INSTALL REAR SEATBACK LOCK RELEASE BUTTON

a.

Install the 2 rear seatback lock release buttons to the reclining release handle sub-assembly.


Hide 24.INSTALL NO. 1 SEATBACK PAD RH

B277451

a.

Install the rear No. 1 seatback pad RH to the rear No. 1 seatback frame.


Hide 25.INSTALL REAR SEAT ARMREST BUSH LH (w/ Center Armrest)

a.

Install the rear seat armrest bush LH to the rear seat armrest arm LH.


Hide 26.INSTALL REAR SEAT ARMREST ARM LH (w/ Center Armrest)

a.

Install the rear seat armrest arm LH to the rear seat armrest with the bolt.


Hide 27.INSTALL REAR SEAT ARMREST BUSH RH (w/ Center Armrest)

HINT:

Use the same procedure described for the LH side.


Hide 28.INSTALL REAR SEAT ARMREST ARM RH (w/ Center Armrest)

HINT:

Use the same procedure described for the LH side.


Hide 29.INSTALL REAR NO. 1 SEATBACK COVER RH

B277447
1.99,3.167 1.802,3.167 1.802,3.167 1.688,3.875 false 2.021,3.073 2.354,3.448 0.333,0.375 10 false *1
*1 Hog Ring Pliers


a.

Using hog ring pliers, install the rear No. 1 seatback cover RH to the No. 1 seatback pad RH with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B277449

Attach the 4 claws to install the 2 rear seat headrest supports.


c.

Attach the 2 hooks.

B277445


d.

w/ Center Armrest:

i.
B277443

Temporarily install the rear seat armrest assembly RH to the rear No. 1 seatback frame, and then slide the rear No. 1 seatback cover RH behind the rear of the rear seat armrest assembly RH.


ii.
B277441
2.031,3.146 1.792,3.146 1.792,3.146 1.646,3.885 false 2.063,3.063 2.375,3.375 0.313,0.313 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the rear No. 1 seatback cover RH to the rear No. 1 seatback frame assembly with new hog rings.


iii.

Install the 2 nuts.



e.

Close the fastener and attach the 3 hooks.

B277438
1.281,1.5 1.177,1.5 1.177,1.5 1.094,1.552 false 5.906,1.438 6.031,1.438 6.031,1.438 6.146,1.49 false 3.604,2.177 3.604,1.604 3.604,1.604 3.792,1.604 false 2.781,1.927 2.604,1.927 2.604,1.927 2.354,1.76 false 1.313,1.427 1.563,1.635 0.25,0.208 10 false *1 5.729,1.375 6.052,1.625 0.323,0.25 10 false *1 3.833,1.531 4.094,1.74 0.26,0.208 10 false *1 2.813,1.854 3.156,2.167 0.344,0.313 10 false *2
*1 Hook *2 Fastener



Hide 30.INSTALL REAR NO. 1 SEATBACK ASSEMBLY RH

a.

Install the rear No. 1 seatback assembly with the 4 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 32.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

a.
B281433

Attach the guide and claw to install the rear No. 1 seat reclining cover RH.


b.

Install the screw.


Hide 33.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

a.
B277458

Install the reclining adjuster release handle RH with the screw.


Hide 34.INSTALL REAR NO. 1 SEAT RECLINING COVER LH

a.
B281434

Attach the guide and claw to install the rear No. 1 seat reclining cover LH


b.

Install the screw.


Hide 35.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the rear seat headrest assembly.