Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY
RM1880E _58 Vehicle Interior _013243 SEAT _0068646 REAR NO. 2 SEAT ASSEMBLY A

SEAT  REAR NO. 2 SEAT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSTALL NO. 2 SEAT CUSHION PAD RH

NOTICE:
·

As the No. 2 seat cushion pad RH is affixed to the No. 2 seat cushion frame sub-assembly RH, do not remove the No. 2 seat cushion pad RH from the No. 2 seat cushion frame sub-assembly RH unless it is necessary to replace the No. 2 seat cushion pad RH. If the No. 2 seat cushion pad RH is removed from the No. 2 seat cushion frame sub-assembly RH, make sure to replace the No. 2 seat cushion pad RH.

·

Perform the following only when replacing the No. 2 seat cushion pad RH or No. 2 seat cushion frame sub-assembly RH.



a.

When reusing the No. 2 seat cushion frame sub-assembly RH:

i.
B278510
3.177,1.25 2.823,1.25 true 3.198,1.167 3.427,1.427 0.229,0.26 10 false *1
*1 Adhesive Area


Remove any adhesive remaining in the area shown in the illustration.


ii.

Install a new No. 2 seat cushion pad RH to the No. 2 seat cushion frame sub-assembly RH.



b.

When using a new No. 2 seat cushion frame sub-assembly RH:

Install a new No. 2 seat cushion pad RH to the No. 2 seat cushion frame sub-assembly RH.


Hide 2.INSTALL NO. 2 FOLD SEAT STOPPER BAND ASSEMBLY

a.
B278508
1.417,1.583 1.5,1.583 1.5,1.583 1.646,1.208 true 1.167,0.917 1.25,0.917 1.25,0.917 1.521,1.052 true 1.198,1.5 1.5,1.75 0.302,0.25 10 false *1 0.969,0.844 1.219,1.083 0.25,0.24 10 false *1
*1 Protruding Part


Install the No. 2 fold seat stopper band assembly with the screw.

NOTICE:

Do not allow the anchor part of the No. 2 fold seat stopper band assembly to overlap the protruding parts.



Hide 3.INSTALL NO. 2 SEAT CUSHION COVER SUB-ASSEMBLY RH

a.
B277265
2.25,0.99 2.115,0.99 false 2.115,0.99 2,1.688 false 2.271,0.906 2.635,1.281 0.365,0.375 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the No. 2 seat cushion cover sub-assembly RH to the No. 2 seat cushion pad RH with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B278505

Attach the No. 2 seat cushion cover sub-assembly RH.


c.
B278503
2.167,0.719 2.073,0.719 false 2.073,0.719 1.802,1.604 false 2.188,0.625 2.479,0.948 0.292,0.323 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the No. 2 seat cushion cover sub-assembly RH to the No. 2 seat cushion frame sub-assembly RH with new hog rings.


d.
B278501

Pass the bracket of the No. 2 seat cushion frame sub-assembly RH through the slit of the No. 2 seat cushion cover sub-assembly RH and close the No. 2 seat cushion cover sub-assembly RH.


e.
B278499

Close the fastener.


f.
B278497

Pass the No. 2 fold seat stopper band assembly through the hole in the No. 2 seat cushion cover sub-assembly RH.


g.
B278495

Close the fastener.


h.
B278493

Close the fastener.


i.

Attach the 4 hooks.


Hide 4.INSTALL NO. 2 SEAT LEG SUB-ASSEMBLY RH

a.
B277679
1,2.021 0.917,2.021 false 0.917,2.021 0.604,1.781 true 1.021,1.917 1.604,2.135 0.583,0.219 10 false *1
*1 Bracket of No. 2 Seat Cushion Frame Sub-assembly RH


Install the No. 2 seat leg sub-assembly RH with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

The No. 2 seat leg sub-assembly RH will turn together with the bolts when the bolts are tightened, so be sure not to deform the bracket of the No. 2 seat cushion frame sub-assembly RH.



Hide 5.INSTALL REAR SEAT CUSHION SPRING

a.
B277642
3.281,2.115 3.365,2.115 false
V100135

MP Grease


Apply MP grease to the locations shown in the illustration.


b.
B277678

Install the rear seat cushion spring as shown in the illustration.


Hide 6.INSTALL REAR NO. 2 SEAT CENTER LAP TYPE BELT ASSEMBLY (for RH Side)

Hide 7.INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY RH (for RH Side)

Hide 8.INSTALL REAR NO. 2 SEAT LAP TYPE BELT ASSEMBLY LH (for LH Side)

Hide 9.INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY LH (for LH Side)

Hide 10.INSTALL NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY

a.
B277676

Install the No. 2 seat reclining release handle sub-assembly as shown in the illustration.


Hide 11.INSTALL NO. 3 SEAT CUSHION HINGE COVER RH

a.

Install the No. 3 seat cushion hinge cover RH with the screw.


b.

Install the clip.


Hide 12.INSTALL REAR NO. 1 SEAT CUSHION HINGE COVER

a.

Install the rear No. 1 seat cushion hinge cover with the 2 clips.


Hide 13.INSTALL REAR SEAT LEG COVER RH

B277675

a.

Pass the No. 2 seat reclining release handle sub-assembly through the hole of the rear seat leg cover RH.


b.

Attach the 2 claws to install the rear seat leg cover RH.


c.

Install the 3 screws.


d.

Pass the No. 2 seat reclining release handle sub-assembly through the hole of the No. 3 seat cushion hinge cover RH.


Hide 14.INSTALL REAR SEATBACK STOP RELEASE BUTTON

a.
B277243

Install the 2 rear seatback stop release buttons as shown in the illustration.


Hide 15.INSTALL REAR SEAT HINGE COVER

a.

Attach the guide to install the rear seat hinge cover.


b.

Attach the 2 claws.


c.

Install the 2 screws.


d.

Install the 2 clips.


Hide 16.INSTALL REAR OUTER NO. 3 SEAT LEG SUB-ASSEMBLY RH

B277239
3.281,2.115 3.365,2.115 false
V100135

MP Grease


a.

Apply MP grease to the location shown in the illustration.


b.

Install the rear outer No. 3 seat leg sub-assembly RH with the 2 plates and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17.INSTALL FRONT OUTER NO. 3 SEAT LEG SUB-ASSEMBLY RH

B276798
3.281,2.104 3.365,2.104 false
V100135

MP Grease


a.

Apply MP grease to the location shown in the illustration.


b.

Install the front outer No. 3 seat leg sub-assembly RH with the 2 plates and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 18.INSTALL NO. 2 SEAT CUSHION PLATE

a.

Install the No. 2 seat cushion plate with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 19.INSTALL NO. 2 SEATBACK PAD RH

a.

Install the No. 2 seatback pad RH to the No. 2 seatback frame sub-assembly RH.


Hide 20.INSTALL NO. 2 SEATBACK COVER SUB-ASSEMBLY RH

a.
B276795
2.25,0.969 2.156,0.969 false 2.156,0.969 1.948,1.635 false 2.281,0.885 2.688,1.24 0.406,0.354 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the No. 2 seatback cover sub-assembly RH with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.

Attach the 4 claws to install the 2 rear No. 2 seat headrest supports.


c.
B276792

Attach the hook.


d.

Attach the hook labeled A and 2 pieces of fastening tape labeled A.


e.

Attach the hook labeled B and fastening tape labeled B.

B277668
3.469,1.635 3.594,1.635 3.594,1.635 3.594,1.333 true 2.885,1.594 3,1.594 3,1.594 3,1.24 true 4.01,1.573 4.125,1.573 4.125,1.573 4.125,1.25 true 5.792,0.156 5.708,0.156 false 5.708,0.156 5.552,0.604 true 2,0.25 1.906,0.25 false 1.917,0.25 1.604,0.875 true 3.271,1.563 3.635,1.771 0.365,0.208 10 false *1 2.708,1.51 3.083,1.781 0.375,0.271 10 false *2 3.833,1.49 4.167,1.75 0.333,0.26 10 false *2 5.854,0.073 6.219,0.313 0.365,0.24 10 false *3 2.052,0.167 2.354,0.417 0.302,0.25 10 false *4
*1 Hook A *2 Fastening Tape A
*3 Hook B *4 Fastening Tape B



f.
B276789
2.917,0.583 2.75,0.583 2.75,0.583 2.604,1.052 false 2.75,1.25 2.833,1.667 2.833,1.667 3,1.667 false 2.969,0.521 3.25,0.917 0.281,0.396 10 false *1 3.042,1.583 3.25,1.833 0.208,0.25 10 false *2
*1 Spacer
*2 Plate


Install the rear No. 2 seatback assembly.

i.

LH side:

Install the rear No. 2 seatback assembly with the plate, spacer and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


ii.

RH side:

Install the rear No. 2 seatback assembly with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)



Hide 21.INSTALL REAR NO. 2 SEAT RECLINING COVER RH

a.

Install the rear No. 2 seat reclining cover RH with the 2 screws.


Hide 22.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH

a.

Install the No. 1 reclining adjuster release handle RH with the screw.


Hide 23.INSTALL REAR SEAT LOWER CUSHION HINGE COVER RH

a.

Install the rear seat lower cushion hinge cover RH with the 2 screws.


Hide 24.INSTALL REAR NO. 2 SEAT HEADREST ASSEMBLY RH

a.

Install the rear No. 2 seat headrest assembly RH.