Home › Vehicle Interior › SEAT BELT › REAR NO. 2 SEAT INNER BELT ASSEMBLY
RM1880E _58 Vehicle Interior _013244 SEAT BELT _0068657 REAR NO. 2 SEAT INNER BELT ASSEMBLY A

SEAT BELT  REAR NO. 2 SEAT INNER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (see page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 1.INSTALL REAR NO. 2 SEAT LAP TYPE BELT ASSEMBLY LH (for LH Side)

B342838
2.146,1.292 2.417,0.76 2.417,0.76 2.667,0.76 true 1.708,1.573 1.167,1.01 1.167,1.01 1.031,1.01 true 2.719,0.677 3.031,0.875 0.313,0.198 10 false *1 0.844,0.927 1.156,1.125 0.313,0.198 10 false *1 0.521,1.521 0.75,1.75 0.229,0.229 10 true *a
*1 Protruding Part
*a Front


a.

Install the rear No. 2 seat lap type belt assembly LH.

NOTICE:

Do not allow the anchor part of the seat belt to overlap the protruding part of the seat leg sub-assembly.



Hide 2.INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY LH (for LH Side)

B342839
2.146,1.302 2.417,0.833 2.417,0.833 2.667,0.833 true 1.708,1.594 1.302,1.979 1.302,1.979 0.969,1.979 true 0.74,1.896 1.063,2.104 0.323,0.208 10 false *1 2.74,0.771 3.042,1.063 0.302,0.292 10 false *1 0.729,1.073 1.042,1.271 0.313,0.198 10 true *a
*1 Protruding Part
*a Front


a.

Install the rear No. 2 seat inner belt sub-assembly LH with the nut as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not allow the anchor part of the seat belt to overlap the protruding part of the seat leg sub-assembly.



Hide 3.INSTALL REAR NO. 2 SEAT CENTER LAP TYPE BELT ASSEMBLY (for RH Side)

B342840
1.667,1.604 2.167,1.604 true 0.667,0.531 0.917,0.531 0.917,0.531 1.25,1.281 true 2.24,1.542 2.573,1.813 0.333,0.271 10 false *1 0.458,0.438 0.792,0.708 0.333,0.271 10 false *1 2.542,1.083 2.875,1.354 0.333,0.271 10 false *a
*1 Protruding Part
*a Front


a.

Install the rear No. 2 seat center lap type belt assembly.

NOTICE:

Do not allow the anchor part of the seat belt to overlap the protruding part of the seat leg sub-assembly.



Hide 4.INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY RH (for RH Side)

B342841
1.677,1.604 2.01,1.604 true 0.5,0.75 0.75,0.75 0.75,0.75 1.24,1.281 true 0.292,0.677 0.583,0.917 0.292,0.24 10 false *1 2.073,1.531 2.385,1.729 0.313,0.198 10 false *1 2.5,1.083 2.813,1.281 0.313,0.198 10 false *a
*1 Protruding Part
*a Front


a.

Install the rear No. 2 seat inner belt sub-assembly RH with the nut as shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

NOTICE:

Do not allow the anchor part of the seat belt to overlap the protruding part of the seat leg sub-assembly.



Hide 5.INSTALL REAR NO. 2 SEAT ASSEMBLY

a.

Install the rear No. 2 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY>INSTALLATION).