Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068660 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  11  Room Temperature Sensor Circuit  


DESCRIPTION

The cooler thermistor is installed in the instrument panel to detect the room temperature and control the heater and air conditioning AUTO function. The resistance of the cooler thermistor changes in accordance with the room temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the cooler thermistor and reads voltage changes as the resistance of the cooler thermistor changes.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
11 Room Temperature Sensor Circuit An open or short in the room temperature sensor circuit.
·

Cooler thermistor

·

Air conditioning amplifier assembly

·

Harness or connector


Memorized
(8.5 min. or more)
If the room temperature is approximately - 18.6°C (1.48°F) or lower, DTC 11 may be output even though the system is normal.

HINT:

Memory: The air conditioning amplifier stores the DTC of the respective malfunction that has been detected for the period of time indicated in parentheses.


WIRING DIAGRAM

E227733
5.563,0.75 5.917,1.01 0.354,0.26 10 false TR 0.875,1.469 1.344,1.823 0.469,0.354 10 false G110 5.271,2.719 5.708,3.021 0.438,0.302 10 false G95 5.281,2.104 5.604,2.396 0.323,0.292 10 false 13 5.271,0.646 5.646,0.979 0.375,0.333 10 false 18 2.438,1.26 2.708,1.563 0.271,0.302 10 false 2 2.448,1.74 2.708,2.042 0.26,0.302 10 false 1 5.542,2.208 6.073,2.552 0.531,0.344 10 false SG-3 5.281,2.885 6.833,3.552 1.552,0.667 10 false Air Conditioning Amplifier Assembly 0.875,1.635 2.167,2.021 1.292,0.385 10 false Cooler Thermistor

PROCEDURE

1.INSPECT COOLER THERMISTOR

b.
E271487
0.125,1.646 0.438,1.938 0.313,0.292 10 *a 1.552,4.396 1.802,4.635 0.25,0.24 10 *b
*a Resistance (kΩ)
*b Temperature


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 10°C (50°F) 3.00 to 3.73 kΩ
15°C (59°F) 2.45 to 2.88 kΩ
20°C (68°F) 1.95 to 2.30 kΩ
25°C (77°F) 1.60 to 1.80 kΩ
30°C (86°F) 1.28 to 1.47 kΩ
35°C (95°F) 1.00 to 1.22 kΩ
40°C (104°F) 0.80 to 1.00 kΩ
45°C (113°F) 0.65 to 0.85 kΩ
50°C (122°F) 0.50 to 0.70 kΩ
55°C (131°F) 0.44 to 0.60 kΩ
60°C (140°F) 0.36 to 0.50 kΩ



NOTICE:
·

Even slightly touching the thermistor may change the resistance value. Be sure to hold the connector of the thermistor.

·

When measuring the resistance, the cooler thermistor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (Refer to the graph).


Result:
Proceed to
OK
NG



OK

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY
a.

Remove the air conditioning amplifier assembly with its connectors still connected.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING AMPLIFIER(for Automatic Air Conditioning System)>REMOVAL


b.
E225456
2.146,0.104 2.563,0.354 0.417,0.25 1.719,1.615 2.188,1.01 true 3.031,1.563 2.875,1.188 true 0.115,0.083 0.438,0.427 0.323,0.344 10 false *a 2.229,0.146 2.583,0.458 0.354,0.313 10 false G95 1.448,1.635 1.833,1.938 0.385,0.302 10 false SG-3 3.021,1.552 3.375,1.865 0.354,0.313 10 false TR
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G95-18 (TR) - G95-13 (SG-3)
·

Ignition switch ON

·

Cabin temperature 25°C (77°F)


1.8 to 2.2 V
·

Ignition switch ON

·

Cabin temperature 40°C (104°F)


1.2 to 1.6 V


HINT:

As the temperature increases, the voltage decreases.


Result:
Result Proceed to
OK (When troubleshooting according to problem symptoms table.) A
OK (When troubleshooting according to DTC.) B
NG C




A

B

C

3.CHECK HARNESS AND CONNECTOR (COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER)
3.CHECK HARNESS AND CONNECTOR (COOLER THERMISTOR - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the G110 cooler thermistor connector.


b.

Disconnect the G95 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G95-18 (TR) - G110-2 Always Below 1 Ω
G95-13 (SG-3) - G110-1
G95-18 (TR) - Body ground Always 10 kΩ or higher
G95-13 (SG-3) - Body ground



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR