Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068671 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor and magnet clutch with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new compressor and magnet clutch before installation.

Standard:

(Oil capacity inside the new compressor and magnet clutch: 180 + 15 cc (6.08 + 0.51 fl.oz)) - (Remaining oil amount in the removed compressor and magnet clutch) = (Oil amount to be removed from the new compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

If a new compressor and magnet clutch is installed without removing the oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.

·

If the volume of oil remaining in the removed compressor and magnet clutch is small, check for oil leakage.

·

Be sure to use ND-OIL 8 or equivalent compressor oil.




Hide 2.INSTALL COOLER COMPRESSOR ASSEMBLY

a.

for LHD:

i.
E172837
2.75,0.344 2.896,0.51 0.146,0.167 10 false 1 2.042,1.906 2.188,2.073 0.146,0.167 10 false 2 1.896,0.792 2.115,1.021 0.219,0.229 10 true 4 2.656,1.729 2.802,1.896 0.146,0.167 10 false 3

Install the cooler compressor assembly with the 4 bolts. Tighten the bolts in the order shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


ii.

Connect the connector.



b.

for RHD:

i.
E226331
2.365,0.094 2.594,0.365 0.229,0.271 10 false 1 1,1.01 1.229,1.219 0.229,0.208 10 false 2 1.802,0.917 2.021,1.156 0.219,0.24 10 true 3 1.083,0.24 1.313,0.479 0.229,0.24 10 false 4

Install the cooler compressor assembly with the 4 bolts. Tighten the bolts in the order shown in the illustration.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


ii.

Connect the connector.



Hide 3.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

for LHD:

i.

Remove the vinyl tape attached to the No. 1 cooler refrigerant discharge hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


iv.

Connect the No. 1 cooler refrigerant discharge hose with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.

for RHD:

i.

Remove the vinyl tape attached to the No. 1 cooler refrigerant discharge hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


iv.

Connect the No. 1 cooler refrigerant discharge hose with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 4.INSTALL SUCTION HOSE SUB-ASSEMBLY

a.

for LHD:

i.

Remove the vinyl tape attached to the suction hose sub-assembly.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the suction hose sub-assembly.


iv.

Connect the suction hose sub-assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.

for RHD:

i.

Remove the vinyl tape attached to the suction hose sub-assembly.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the suction hose sub-assembly.


iv.

Connect the suction hose sub-assembly with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)