Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) › 2011.07–2013.08
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068699 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Auto Up / Down Function does not Operate  


DESCRIPTION

If the auto up/down function does not operate, the cause may be one or more of the following:

·

The recorded power window fully closed position, which is stored in the power window regulator master switch assembly, was erased as a result of: 1) the PWR H-fuse or DOOR fuse being replaced; or 2) the battery cable and the master switch's connector being disconnected.

·

The power window regulator master switch assembly has a malfunction.

·

The pulse sensors in the front power window regulator motor assembly RH have a malfunction.

·

The wiring between the power window regulator master switch assembly and the front power window regulator motor assembly RH is open or short-circuited.


WIRING DIAGRAM

B276696
5.385,2.938 7.052,3.594 1.667,0.656 10 false Power Window Regulator Master Switch Assembly 0.271,2.979 2.271,3.635 2,0.656 10 false Front Power Window Regulator Motor Assembly RH 0.896,1.188 1.333,1.49 0.438,0.302 10 false PLS 5.646,0.667 6.094,0.969 0.448,0.302 10 false VCC 5.646,1.177 6.146,1.448 0.5,0.271 10 false PLS 5.646,1.688 6.198,2.031 0.552,0.344 10 false PLS2 5.646,2.208 6.104,2.5 0.458,0.292 10 false GND 0.583,1.698 1.125,2.031 0.542,0.333 10 false PLS 1.729,0.583 2.01,0.875 0.281,0.292 10 false 4 1.729,1.104 2.073,1.406 0.344,0.302 10 false 5 1.74,1.604 2.083,1.917 0.344,0.313 10 false 3 1.74,2.115 2.094,2.458 0.354,0.344 10 false 6 1.281,0.781 1.885,1.094 0.604,0.313 10 false SSRB 1.396,1.292 1.865,1.594 0.469,0.302 10 false PLS 1.313,1.802 1.917,2.115 0.604,0.313 10 false PLS2 1.573,2.302 1.938,2.604 0.365,0.302 10 false E 5.469,0.583 5.708,0.854 0.24,0.271 10 false 3 5.406,1.094 5.677,1.323 0.271,0.229 10 false 14 5.417,1.604 5.792,1.927 0.375,0.323 10 false 17 5.479,2.115 5.844,2.417 0.365,0.302 10 false 2 0.271,2.802 0.583,3.063 0.313,0.26 10 false H2 5.385,2.76 5.781,3.01 0.396,0.25 10 false H8

PROCEDURE

1.CHECK MANUAL UP/DOWN FUNCTION (FOR DRIVER SIDE)
a.

Check that the manual up/down function operates normally.

OK:

Manual up/down function operates normally.



Result:
Proceed to
OK
NG



OK

2.CHECK LIGHT OF POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

2.CHECK LIGHT OF POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Turn the ignition switch ON.


b.
B344987
2.135,0.969 2.458,0.677 2.458,0.677 2.594,0.677 true 2.719,0.583 3.094,0.833 0.375,0.25 10 false *1
*1 AUTO Light


Operate the master switch's driver side power window switch for 2 seconds or more.


c.

Check the blinking pattern of the AUTO light. Compare the blinking pattern with the illustration.

B278579
0.135,1.219 0.573,1.521 0.438,0.302 10 ON 0.135,1.51 0.708,1.823 0.573,0.313 10 OFF 0.135,1.75 0.729,2.042 0.594,0.292 10 (Light) 1.573,1.844 2.042,2.125 0.469,0.281 10 (sec.) 3.083,1.781 3.667,2.094 0.583,0.313 10 (sec.) 4.708,1.865 5.344,2.208 0.635,0.344 10 (sec.) 0.135,0.146 2.354,0.49 2.219,0.344 10 Blinking Pattern of AUTO Light 0.771,0.625 2.385,1.229 1.615,0.604 10 1: Fully closed position is misaligned 2.51,0.625 4.031,1.219 1.521,0.594 10 2: Pulse sensor circuit malfunction 4.125,0.625 5.354,1.094 1.229,0.469 10 3: Both 1 and 2 6.052,0.625 6.958,1.031 0.906,0.406 10 4: Normal 1.156,1.646 1.531,1.948 0.375,0.302 10 1.5 4.302,1.594 4.729,1.938 0.427,0.344 10 1.5 1.219,1.823 1.552,2.094 0.333,0.271 10 2.0 4.354,1.813 4.76,2.115 0.406,0.302 10 2.0 3.76,1.813 4.177,2.104 0.417,0.292 10 1.0 2.729,1.833 3.125,2.146 0.396,0.313 10 1.0 2.438,1.656 2.813,1.938 0.375,0.281 10 0.5 4.01,2.292 4.365,2.604 0.354,0.313 10 0.5

Result:
Blinking Pattern Proceed to
1 or 3 A
2 B
4 C




A

3.RESET FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

C

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

3.RESET FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Check that the power window operates normally after reset.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)>INITIALIZATION

OK:

Power window operates normally.


Result:
Proceed to
OK
NG




OK

END

NG

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the H8 power window regulator master switch assembly connector.


b.

Disconnect the H2 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-3 (VCC) - H2-4 (SSRB) Always Below 1 Ω
H8-14 (PLS) - H2-5 (PLS) Always Below 1 Ω
H8-17 (PLS2) - H2-3 (PLS2) Always Below 1 Ω
H8-2 (GND) - H2-6 (E) Always Below 1 Ω
H8-3 (VCC) or H2-4 (SSRB) - Body ground Always 10 kΩ or higher
H8-14 (PLS) or H2-5 (PLS) - Body ground Always 10 kΩ or higher
H8-17 (PLS2) or H2-3 (PLS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (PLS, PLS2 SIGNAL)
a.

Remove the power window regulator master switch assembly with its connectors still connected.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.
B276285
0.208,0.927 0.625,1.177 0.417,0.25 1.729,0.938 1.5,0.448 true 2.25,0.948 2.396,0.458 true 0.177,0.156 0.49,0.417 0.313,0.26 10 false *a 0.333,0.979 0.813,1.313 0.479,0.333 10 false H8 1.313,0.25 1.792,0.583 0.479,0.333 10 false PLS 2.323,0.26 2.802,0.594 0.479,0.333 10 false PLS2
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)


Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Specified Condition
H8-14 (PLS) - Body ground Ignition switch ON, driver side power window switch off → up or down Pulse waveform is output
H8-17 (PLS2) - Body ground



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY