Home › Vehicle Exterior › WINDOW / GLASS › FRONT SIDE FIX WINDOW GLASS
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068708 FRONT SIDE FIX WINDOW GLASS A

WINDOW / GLASS  FRONT SIDE FIX WINDOW GLASS  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 3.REMOVE FRONT SIDE FIX WINDOW ASSEMBLY LH

a.
B284121
1.125,1.01 1.385,1.24 0.26,0.229 10 false A 1.406,1.448 1.698,1.677 0.292,0.229 10 true A 2.635,2 2.875,2.302 0.24,0.302 10 false B 1.448,2.292 1.708,2.573 0.26,0.281 10 false C 1.885,2.521 2.375,2.844 0.49,0.323 10 false B - B 0.292,2.531 0.927,2.823 0.635,0.292 10 false A - A 0.323,3.458 0.813,3.792 0.49,0.333 10 false C - C 1.167,2.552 1.604,2.854 0.438,0.302 10 false *a 2.281,2.99 2.698,3.344 0.417,0.354 10 false *a 1.156,3.552 1.594,3.875 0.438,0.323 10 false *a 1.427,1.854 1.635,2.042 0.208,0.188 10 true C 1.917,1.802 2.115,2.052 0.198,0.25 10 true B
*a Cut


Using a knife, cut off the moulding as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body with the knife.



b.

Remove the remaining moulding.

HINT:

Make a partial cut in the moulding. Then pull and remove it by hand.



c.
B261232
0.75,0.479 1.229,0.229 true 2.823,1.458 2.302,1.458 true 1.781,3.24 1.406,2.771 1.406,2.771 1.302,2.771 true 1.271,0.094 1.635,0.375 0.365,0.281 10 false *1 2.906,1.333 3.229,1.656 0.323,0.323 10 false *2 1.083,2.667 1.458,2.979 0.375,0.313 10 false *3
*1 Clip
*2 Protective Tape
*3 Piano Wire


Apply protective tape to the outer surface of the vehicle body to prevent scratches.

NOTICE:

When separating the quarter window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.



d.

From the interior, insert a piano wire between the vehicle body and glass as shown in the illustration.


e.

Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




f.

Cut through the adhesive by pulling the piano wire around the glass.

NOTICE:

Leave as much adhesive on the vehicle body as possible when cutting through the adhesive.



g.

Using suction cup, remove the glass.


Hide 4.CLEAN VEHICLE BODY

B106081
0.5,1.292 0.75,0.75 0.75,0.75 0.833,0.75 true 2.26,1.438 2.583,0.75 2.583,0.75 2.667,0.75 true 2.427,1.604 2.427,1.781 false 0.813,1.573 0.813,1.76 false 0.865,0.667 1.219,0.917 0.354,0.25 10 false *1 2.698,0.667 3.031,0.927 0.333,0.26 10 false *1 0.729,1.781 1,2 0.271,0.219 10 false *2 2.344,1.802 2.583,2 0.24,0.198 10 false *2
*1 Adhesive
*2 Vehicle Body


a.

Clean and shape the contact surface of the vehicle body.

i.

On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.

HINT:

Leave as much adhesive on the vehicle body as possible.


NOTICE:

Be careful not to damage the vehicle body.




b.

Clean the contact surface of the vehicle body with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.