Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING
RM1880E _58 Vehicle Interior _013247 INTERIOR PANELS / TRIM _0068695 ROOF HEADLINING A

INTERIOR PANELS / TRIM  ROOF HEADLINING  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 3.REMOVE REAR NO. 2 SEAT ASSEMBLY

Hide 4.REMOVE LOWER FRONT PILLAR GARNISH LH

B279271
1.542,1.833 1.542,2.063 1.542,2.063 1.927,2.063 true 0.896,1.76 0.396,1.76 true 2.01,1.958 2.448,2.177 0.438,0.219 10 false *1 0.188,1.688 0.667,1.958 0.479,0.271 10 false *1
*1 Protective Tape


a.

Put protective tape around the lower front pillar garnish.


b.

Using a screwdriver, detach the 3 claws and 3 guides and remove the lower front pillar garnish.

HINT:

Tape the screwdriver tip before use.



Hide 5.REMOVE LOWER FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 6.REMOVE FRONT PILLAR GARNISH LH

B279270

a.

Detach the 3 clips and remove the front pillar garnish.


Hide 7.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 8.REMOVE FRONT DOOR SCUFF PLATE LH

B279266
0.583,1.396 0.25,1.396 true 0.063,1.323 0.469,1.615 0.406,0.292 10 false *1
*1 Protective Tape


a.

Put protective tape around the front door scuff plate.


b.

Using a moulding remover, detach the 3 clips and 7 claws and remove the front door scuff plate.


Hide 9.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 10.REMOVE FRONT DOOR OPENING TRIM LH

B279289

a.

Remove the front door opening trim.


Hide 11.REMOVE FRONT DOOR OPENING TRIM RH

HINT:

Use the same procedure described for the LH side.


Hide 12.REMOVE REAR DOOR SCUFF PLATE LH

B279267
0.635,1.208 0.281,1.021 true 0.115,0.927 0.313,1.094 0.198,0.167 10 true *1
*1 Protective Tape


a.

Put protective tape around the rear door scuff plate.


b.

Using a moulding remover, detach the 3 clips and 7 claws and remove the rear door scuff plate.


Hide 13.REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 14.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

B279291

a.

Remove the rear door opening trim weatherstrip.


Hide 15.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 16.REMOVE LOWER CENTER PILLAR GARNISH LH

B276978

a.

Remove the bolt and disconnect the front seat outer belt floor anchor.


b.
B279268

Detach the 2 claws and remove the lower center pillar garnish.


Hide 17.REMOVE LOWER CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 18.REMOVE CENTER PILLAR GARNISH LH

B276930
2.104,1.208 2.677,1.208 true 2.76,1.104 3,1.385 0.24,0.281 10 false *1
*1 Protective Tape


a.

Using a screwdriver, detach the 4 claws and remove the front seat belt shoulder anchor cover.

HINT:

Tape the screwdriver tip before use.



b.

Remove the bolt and disconnect the front seat belt shoulder anchor.


c.
B279269

Detach the clip.


d.

Pull the center pillar garnish in the direction indicated by the arrow in the illustration to detach the guide and remove the center pillar garnish.


Hide 19.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 20.REMOVE BACK DOOR SCUFF PLATE

B279272

a.

Detach the 6 clips and 4 claws and remove the back door scuff plate.


Hide 21.REMOVE QUARTER TRIM HOOK

B276937

HINT:

Use the same procedure for both quarter trim hooks.


a.

Remove the screw and quarter trim hook.


Hide 22.REMOVE QUARTER INSIDE TRIM BOARD LH

B279273

a.

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


b.
B279274

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


c.

Using a clip remover, remove the clip.


d.

Detach the 4 claws, 8 clips and 2 guides and remove the quarter inside trim board.

B279275


Hide 23.REMOVE QUARTER INSIDE TRIM BOARD RH

B279278

a.

Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.


b.
B279279

Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.


c.

Remove the clip.


d.

Detach the 4 claws, 8 clips and 2 guides and remove the quarter inside trim board.

B279280


Hide 24.REMOVE QUARTER PILLAR GARNISH LH

B280110
2.052,1.115 2.469,0.688 2.469,0.688 2.594,0.688 false 2.667,0.615 3.125,0.948 0.458,0.333 10 false *1
*1 Protective Tape


a.

Using a screwdriver, detach the 2 claws and open the rear No. 1 seat belt shoulder anchor cover.

HINT:

Tape the screwdriver tip before use.



b.

Remove the bolt and disconnect the rear No. 1 seat belt shoulder anchor.


c.
B279276

Detach the 3 clips and remove the quarter pillar garnish.


Hide 25.REMOVE QUARTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 26.REMOVE INNER UPPER ROOF SIDE GARNISH LH

B280110
2.052,1.115 2.469,0.688 2.469,0.688 2.594,0.688 false 2.667,0.615 3.125,0.948 0.458,0.333 10 false *1
*1 Protective Tape


a.

Using a screwdriver, detach the 2 claws and open the rear No. 2 seat belt shoulder anchor cover.

HINT:

Tape the screwdriver tip before use.



b.
B279277

Detach the 5 clips and remove the inner upper roof side garnish.


Hide 27.REMOVE INNER UPPER ROOF SIDE GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 28.REMOVE MAP LIGHT ASSEMBLY (w/ Map Light)

Hide 32.REMOVE VISOR ASSEMBLY LH

B266814

a.

Detach the guide.


b.

Remove the 2 screws and visor.


Hide 33.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 34.REMOVE VISOR HOLDER LH

B266815

a.

Remove the screw.


b.

Detach the 2 claws and remove the visor holder.


Hide 35.REMOVE VISOR HOLDER RH

HINT:

Use the same procedure described for the LH side.


Hide 36.REMOVE ASSIST GRIP

B277629
1.208,0.99 1.542,1.302 1.542,1.302 1.688,1.302 true 1.74,1.219 2.156,1.521 0.417,0.302 10 false *1
*1 Protective Tape


HINT:

Use the same procedure for all assist grips.


a.

Using a screwdriver, detach the 4 claws and open the 2 covers.

HINT:

Tape the screwdriver tip before use.



b.
B206336

Remove the 2 screws and assist grip.


Hide 37.REMOVE ROOF HEADLINING ASSEMBLY

B286144

a.

Disconnect the connector and detach the 5 clamps from the front pillar.


b.

Using a clip remover, remove the 8 clips.


c.

Detach the 4 fasteners.

B291507
3.823,0.115 4.188,0.448 0.365,0.333 10 false *B 0.292,0.104 0.708,0.438 0.417,0.333 10 false *A
*A for LHD *B for RHD



d.
B279287

Remove the roof headlining as shown in the illustration.

NOTICE:

Be careful not to damage the roof headlining when removing it.



Hide 38.REMOVE FRONT SIDE RAIL SPACER LH

B279281

a.

Detach the 3 claws and remove the front side rail spacer.


Hide 39.REMOVE FRONT SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 40.REMOVE SIDE RAIL SPACER (for LHD)

B291508

a.

Detach the 2 claws and remove the side rail spacer.


Hide 41.REMOVE SIDE RAIL SPACER (for RHD)

HINT:

Use the same procedure described for the LHD.


Hide 42.REMOVE REAR NO. 2 SIDE RAIL SPACER LH

B279284

HINT:

Use the same procedure for all rear No. 2 side rail spacers.


a.

Detach the 2 claws and remove the rear No. 2 side rail spacer.


Hide 43.REMOVE REAR NO. 2 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 44.REMOVE REAR NO. 3 SIDE RAIL SPACER LH

B279285

a.

Detach the 3 claws and remove the rear No. 3 side rail spacer.


Hide 45.REMOVE REAR NO. 3 SIDE RAIL SPACER RH

HINT:

Use the same procedure described for the LH side.


Hide 46.REMOVE REAR NO. 3 SIDE RAIL SPACER LH

B279286

a.

Detach the 3 claws and remove the rear No. 3 side rail spacer.