Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM1880E _59 Vehicle Exterior _013251 WIPER / WASHER _0068726 FRONT WIPER MOTOR A

WIPER / WASHER  FRONT WIPER MOTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Using a T30 "TORX" socket, install the wiper motor with the 2 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.
E225942

Connect the rod of the wiper link to the wiper motor.


c.
E225941
2.24,1.135 2.24,1.813 true 2.177,1.854 2.573,2.042 0.396,0.188 10 false *1
*1 Crank Pivot
V100145

MP grease


Apply MP grease to the front wiper crank pivot of the windshield wiper motor assembly.


d.
E225943

Connect the rod of the wiper link to the wiper motor.


Hide 2.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

E226532

a.

Move the wiper motor and link in the direction shown by the arrow in the illustration to attach the wiper cushion to the body, and install the wiper motor and link.


b.

Install the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 3.INSTALL COWL TOP VENTILATOR LOUVER LH

a.
E226535

Attach the 6 claws and 5 guides to install the cowl top ventilator louver LH.


b.

Install the clip.


Hide 4.INSTALL COWL TOP VENTILATOR LOUVER RH

a.
E271990

Attach the 4 claws and 5 guides to install the cowl top ventilator louver RH.


b.

Install the clip.


Hide 5.INSTALL HOOD TO COWL TOP SEAL

a.

Attach the 9 clips to install the seal.


Hide 6.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

a.

Operate the wiper and stop the front wiper motor and link at the automatic stop position.


b.
E177697
0.552,2.99 0.771,2.99 0.771,2.99 1.01,3.365 false 2.5,3.313 2.271,3.313 2.271,3.313 1.885,3.573 false 0.552,1.094 0.906,1.094 0.906,1.094 1.365,1.49 true 0.333,1.031 0.604,1.271 0.271,0.24 10 false *1 0.333,2.927 0.604,3.167 0.271,0.24 10 false *2 2.563,3.24 2.833,3.479 0.271,0.24 10 false *3
*1 Wiper Arm Serrations
*2 Wire Brush
*3 Wiper Pivot Serrations


Clean the wiper arm serrations.


c.

When reusing the front wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



d.

Position the blade tip within the range shown in the illustration.

i.
E226539
0.844,0.708 0.844,0.51 0.844,0.51 0.917,0.51 false 0.844,1 0.844,1.167 0.844,1.167 0.938,1.167 false 0.635,0.927 0.635,1.177 0.635,1.177 0.521,1.177 false 0.927,0.885 0.927,0.958 0.927,0.958 1.135,0.958 false 0.969,0.438 1.24,0.646 0.271,0.208 10 false *a 0.333,1.094 1.01,1.521 0.677,0.427 10 false *b 0.99,1.083 1.323,1.417 0.333,0.333 10 false *c 0.323,0.708 0.667,1 0.344,0.292 10 false *b 1.188,0.896 1.563,1.208 0.375,0.313 10 false *1
*1 Mark for Blade Position
*a Upper Limit
*b 10 mm (0.393 in.)
*c Lower Limit


for LHD:

HINT:

The blade position is indicated by the mark on the glass.



ii.
E226542
1.938,0.896 1.938,0.792 false 1.917,1.198 1.917,1.281 false 1.917,1.083 1.917,1.156 1.917,1.156 1.625,1.156 false 2.167,1.125 2.229,1.354 2.229,1.354 2.323,1.354 false 1.458,1.073 1.76,1.406 0.302,0.333 10 false *1 1.865,0.635 2.115,0.823 0.25,0.188 10 false *a 1.854,1.292 2.146,1.563 0.292,0.271 10 false *c 2.375,0.917 2.625,1.146 0.25,0.229 10 false *b 2.354,1.25 2.646,1.49 0.292,0.24 10 false *b
*1 Mark for Blade Position
*a Upper Limit
*b 10 mm (0.393 in.)
*c Lower Limit


for RHD:

HINT:

The blade position is indicated by the mark on the glass.




e.

Install the front wiper arm and blade assembly RH with the nut.

Torque:
20.5 N*m (209 kgf*cm, 15 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.



Hide 7.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

a.

Operate the wiper and stop the front wiper motor and link at the automatic stop position.


b.
E177697
0.552,2.99 0.771,2.99 0.771,2.99 1.01,3.365 false 2.5,3.313 2.271,3.313 2.271,3.313 1.885,3.573 false 0.552,1.094 0.906,1.094 0.906,1.094 1.365,1.49 true 0.333,1.031 0.604,1.271 0.271,0.24 10 false *1 0.333,2.927 0.604,3.167 0.271,0.24 10 false *2 2.563,3.24 2.833,3.479 0.271,0.24 10 false *3
*1 Wiper Arm Serrations
*2 Wire Brush
*3 Wiper Pivot Serrations


Clean the wiper arm serrations.


c.

When reusing the front wiper motor and link assembly:

i.

Clean the wiper pivot serrations with a wire brush.



d.

Position the blade tip within the range shown in the illustration.

i.
E226541
1.521,1.094 1.521,1.167 1.521,1.167 1.719,1.167 false 1.219,1.135 1.219,1.365 1.219,1.365 1.115,1.365 false 1.458,0.917 1.458,0.75 1.458,0.75 1.521,0.75 false 1.448,1.208 1.448,1.344 1.448,1.344 1.542,1.344 false 1.771,1.104 1.979,1.302 0.208,0.198 10 false *1 1.573,0.677 1.865,0.927 0.292,0.25 10 false *a 1.594,1.26 1.854,1.531 0.26,0.271 10 false *c 0.917,0.906 1.229,1.177 0.313,0.271 10 false *b 0.927,1.271 1.198,1.573 0.271,0.302 10 false *b
*1 Mark for Blade Position
*a Upper Limit
*b 10 mm (0.393 in.)
*c Lower Limit


for LHD:

HINT:

The blade position is indicated by the mark on the glass.



ii.
E226540
2.51,0.885 2.51,0.958 2.51,0.958 2.24,0.958 false 2.542,0.698 2.542,0.594 false 2.5,1.094 2.5,1 false 2.792,0.917 2.792,1.135 2.792,1.135 2.917,1.135 false 2.052,0.896 2.375,1.125 0.323,0.229 10 false *1 2.469,0.438 2.74,0.74 0.271,0.302 10 false *a 2.969,1.063 3.229,1.25 0.26,0.188 10 false *b 2.438,1.115 2.635,1.406 0.198,0.292 10 false *c 2.969,0.729 3.188,0.917 0.219,0.188 10 false *b
*1 Mark for Blade Position
*a Upper Limit
*b 10 mm (0.393 in.)
*c Lower Limit


for RHD:

HINT:

The blade position is indicated by the mark on the glass.




e.

Install the front wiper arm and blade assembly LH with the nut.

Torque:
20.5 N*m (209 kgf*cm, 15 ft.*lbf)

HINT:

Hold the arm hinge by hand when tightening the nut.



f.

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.


Hide 8.INSTALL FRONT WIPER ARM HEAD CAP

a.

Install the front wiper arm head cap.

HINT:

Use the same procedure for both front wiper arm head caps.



Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).