1.REMOVE FILLER PLUG
Remove the filler plug and gasket from the transmission case.
2.REMOVE DRAIN PLUG
Remove the drain plug and gasket from the transmission case.
3.REMOVE CLUTCH RELEASE FORK BOOT
4.REMOVE CLUTCH RELEASE BEARING ASSEMBLY
5.REMOVE RELEASE FORK SUPPORT
6.REMOVE CLUTCH HOUSING
Remove the 9 bolts.
Using a plastic-faced hammer, tap off the clutch housing from the transmission case.
7.REMOVE BACK-UP LIGHT SWITCH ASSEMBLY
Using SST, remove the back-up light switch and gasket from the transmission case.
8.REMOVE SPEEDOMETER SENSOR
Remove the bolt and speedometer sensor.
Remove the O-ring from the speedometer sensor.
9.REMOVE RESTRICT PIN
Remove the 2 restrict pins from the extension housing.
10.REMOVE CONTROL SHIFT LEVER RETAINER
Remove the 6 bolts.
Remove the control shift lever retainer.
Remove the control shift lever retainer gasket.
11.REMOVE EXTENSION HOUSING
Remove the bolt from the shift lever housing.
Remove the 10 bolts.
Using a plastic-faced hammer, tap the extension housing and remove the shift lever housing and the shift and select lever from the transmission case.
12.REMOVE OIL RECEIVER PIPE
13.REMOVE OIL RECEIVER
Remove the bolt and oil receiver.
14.REMOVE REVERSE RESTRICT PIN
Using a T40 ''TORX'' socket wrench, remove the plug.
Using a 5 mm pin punch and a hammer, tap out the restrict slotted pin.
Remove the restrict pin.
15.REMOVE MANUAL TRANSMISSION EXTENSION HOUSING OIL SEAL
Using a screwdriver and hammer, tap out the manual transmission extension housing oil seal from the extension housing.
16.REMOVE FRONT BEARING RETAINER
Remove the 8 bolts.
Using a brass bar and hammer, tap off the retainer from the transmission case.
17.REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL
Secure the front bearing retainer in a vise.
Using SST, tap out the oil seal.
18.REMOVE FRONT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the snap ring from the transmission case.
19.REMOVE NO. 1 COUNTER GEAR FRONT BEARING SNAP RING
Using a snap ring expander, remove the snap ring from the transmission case.
20.REMOVE MANUAL TRANSMISSION CASE
Using a brass bar and hammer, tap off the transmission case from the intermediate plate.
21.REMOVE TRANSMISSION MAGNET
Remove the magnet from the intermediate plate.
22.SECURE INTERMEDIATE PLATE
Secure the intermediate plate in a vise between aluminum plates.
23.REMOVE NO. 1 SHIFT DETENT BALL SPRING SEAT
Using a T40 ''TORX'' socket wrench, remove the spring seat from the intermediate plate.
Using a magnet hand, remove the compression spring and detent ball from the intermediate plate.
Using a T40 ''TORX'' socket wrench, remove the 2 spring seats from the intermediate plate.
Using a magnet hand, remove the 2 compression springs and 2 detent balls from the intermediate plate.
24.REMOVE NO. 2 SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 2 shift fork shaft.
Use a cloth to prevent the snap ring from flying off.
Remove the bolt from the No. 2 shift fork.
Remove the No. 2 shift fork shaft from the intermediate plate.
Remove the No. 2 shift fork from the No. 2 transmission hub sleeve.
Using a magnet hand, remove the No. 1 shift interlock roller and shift interlock pin from the intermediate plate.
25.REMOVE NO. 1 SHIFT FORK SHAFT
Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 1 shift fork shaft.
Use a cloth to prevent the snap ring from flying off.
Remove the bolt from the No. 1 shift fork.
Remove the No. 1 shift fork shaft from the intermediate plate.
Remove the No. 1 shift fork from the reverse gear.
Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.
26.REMOVE NO. 3 SHIFT FORK SHAFT
Using a 5 mm pin punch and hammer, tap out the shift fork set slotted pin from the No. 3 shift fork.
Using 2 screwdrivers and a hammer, tap off the snap ring from the No. 3 shift fork shaft.
Use a cloth to prevent the snap ring from flying off.
Using a magnet hand, remove the straight pin from the reverse shift fork.
Remove the No. 3 shift fork and No. 3 shift fork shaft from the intermediate plate.
Using a magnet hand, remove the No. 1 shift interlock roller from the intermediate plate.
27.REMOVE REVERSE SHIFT FORK
Remove the reverse shift fork from the reverse shift arm.
28.REMOVE REVERSE SHIFT ARM BRACKET
Remove the torsion spring from the reverse shift arm bracket.
Remove the 2 bolts and reverse shift arm bracket from the intermediate plate.
Using a screwdriver, pry out the snap ring from the reverse shift arm bracket.
Remove the reverse shift arm from the reverse shift arm bracket.
29.REMOVE SPEEDOMETER DRIVE GEAR
Using snap ring pliers, remove the snap ring.
Remove the drive gear.
Using a magnet hand, remove the steel ball.
Using snap ring pliers, remove the snap ring.
30.REMOVE OUTPUT SHAFT REAR BEARING
Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the output shaft.
Using SST, remove the rear bearing and output shaft spacer from the output shaft.
31.INSPECT COUNTER 5TH GEAR THRUST CLEARANCE
32.INSPECT COUNTER 5TH GEAR RADIAL CLEARANCE
33.REMOVE COUNTER GEAR REAR SHAFT SNAP RING
Using 2 screwdrivers and a hammer, tap off the snap ring from the counter gear.
34.REMOVE NO. 3 TRANSMISSION HUB SLEEVE
Remove the No. 3 transmission hub sleeve from the counter 5th gear.
35.REMOVE COUNTER 5TH GEAR
Using SST, remove the counter 5th gear together with the 2 No. 3 synchromesh shifting keys, 2 No. 3 synchromesh shifting key springs, No. 3 synchronizer ring and No. 5 gear spline piece from the counter gear.
36.REMOVE NO. 5 GEAR SPLINE PIECE
Remove the No. 5 gear spline piece from the counter 5th gear.
37.REMOVE NO. 3 SYNCHRONIZER RING
Remove the synchronizer ring from the counter 5th gear.
38.REMOVE COUNTER 5TH GEAR BEARING
Remove the bearing from the counter 5th gear.
39.REMOVE NO. 3 SYNCHROMESH SHIFTING KEY
Using a snap ring expander, remove the snap ring.
Remove the No. 3 synchromesh shifting key spring and 2 No. 3 synchromesh shifting keys from the counter 5th gear.
40.REMOVE 5TH GEAR THRUST WASHER
Remove the thrust washer from the counter gear.
41.REMOVE 5TH GEAR THRUST WASHER PIN
Remove the thrust washer pin from the counter gear.
42.REMOVE REAR BEARING RETAINER
Remove the 4 bolts and bearing retainer from the intermediate plate.
43.REMOVE REVERSE IDLER GEAR
Pull out the reverse idler gear shaft from the rear side and remove the reverse idler gear from the intermediate plate.
44.REMOVE COUNTER SHAFT CENTER BEARING
Using a snap ring expander, remove the snap ring.
Using SST, remove the center bearing from the intermediate plate.
Remove the bearing while tapping the tip of the counter gear so that the counter gear does not hit the side wall of the output shaft gear by being pushed forward.
45.REMOVE COUNTER GEAR ASSEMBLY
Remove the counter gear from the intermediate plate.
46.REMOVE INPUT SHAFT ASSEMBLY
Remove the input shaft and No. 2 synchronizer ring from the output shaft.
Do not drop the input shaft bearing or No. 2 synchronizer ring.
47.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING
Using a snap ring expander, remove the snap ring from the output shaft.
48.REMOVE OUTPUT SHAFT ASSEMBLY
Using a plastic-faced hammer, remove the output shaft by tapping the intermediate plate.
49.INSPECT NO. 3 SYNCHRONIZER RING
50.INSPECT NO. 3 TRANSMISSION HUB SLEEVE
51.INSPECT COUNTER 5TH GEAR
52.INSPECT REVERSE IDLER GEAR SUB-ASSEMBLY
53.INSPECT REVERSE IDLER GEAR RADIAL CLEARANCE