TERMINALS OF ECU
System information · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
| CHECK FRONT POWER SEAT SWITCH (for LHD) |


Disconnect the b4 and b5 connectors from the front power seat switch LH.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
b4-1 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
b4-2 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
b4-6 (+B2) - b4-1 (GND2)
SB - W-B
Power source
Always
11 to 14 V
b4-7 (+B) - b4-2 (GND)
W - W-B
Power source
Always
11 to 14 V
b5-12 (SYSB) - b4-2 (GND)
P - W-B
System power source
Always
11 to 14 V
Reconnect the b4 and b5 switch connectors.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the front power seat switch may have a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
b4-3 (SLD+) - b4-2 (GND)
L - W-B
Sliding motor signal (forward)
Slide switch off
Below 1 V
Slide switch on (Forward)
11 to 14 V
b4-4 (SLD-) - b4-2 (GND)
GR - W-B
Sliding motor signal (rearward)
Slide switch off
Below 1 V
Slide switch on (Rearward)
11 to 14 V
b4-5 (FRV-) - b4-2 (GND)
R - W-B
Front vertical motor signal (downward)
Front vertical switch off
Below 1 V
Front vertical switch on (Downward)
11 to 14 V
b4-8 (FRV+) - b4-2 (GND)
B - W-B
Front vertical motor signal (upward)
Front vertical switch off
Below 1 V
Front vertical switch on (Upward)
11 to 14 V
b4-9 (RCL+) - b4-2 (GND)
P - W-B
Reclining motor signal (forward)
Reclining switch off
Below 1 V
Reclining switch on (Forward)
11 to 14 V
b4-11 (RCL-) - b4-2 (GND)
LG - W-B
Reclining motor signal (rearward)
Reclining switch off
Below 1 V
Reclining switch on (Rearward)
11 to 14 V
b4-10 (LFT+) - b4-2 (GND)
V - W-B
Lifter motor signal (upward)
Lifter switch off
Below 1 V
Lifter switch on (Upward)
11 to 14 V
b4-12 (LFT-) - b4-2 (GND)
G - W-B
Lifter motor signal (downward)
Lifter switch off
Below 1 V
Lifter switch on (Downward)
11 to 14 V
b5-1 (SGND) - b4-2 (GND)
BR - W-B
Ground
Always
Below 1 Ω
b5-3 (SSFV) - b5-1 (SGND)
R - BR
Front vertical position signal
Front vertical function operating
4.5 to 4.8 V
b5-4 (SSRL) - b5-1 (SGND)
P - BR
Lifter position signal
Lifter function operating
4.5 to 4.8 V
b5-5 (SSRS) - b5-1 (SGND)
G- BR
Slide position signal
Slide function operating
4.5 to 4.8 V
b5-11 (SSRR) - b5-1 (SGND)
V - BR
Reclining position signal
Reclining function operating
4.5 to 4.8 V
| CHECK FRONT POWER SEAT SWITCH (for RHD) |


Disconnect the a4 and a5 connectors from the front power seat switch RH.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
a4-1 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
a4-2 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
a4-6 (+B2) - a4-1 (GND2)
SB - W-B
Power source
Always
11 to 14 V
a4-7 (+B) - a4-2 (GND)
W - W-B
Power source
Always
11 to 14 V
a5-12 (SYSB) - a4-2 (GND)
P - W-B
System power source
Always
11 to 14 V
Reconnect the a4 and a5 switch connectors.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the front power seat switch may have a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
a4-3 (SLD+) - a4-2 (GND)
L - W-B
Sliding motor signal (forward)
Slide switch off
Below 1 V
Slide switch on (Forward)
11 to 14 V
a4-4 (SLD-) - a4-2 (GND)
GR - W-B
Sliding motor signal (rearward)
Slide switch off
Below 1 V
Slide switch on (Rearward)
11 to 14 V
a4-5 (FRV-) - a4-2 (GND)
R - W-B
Front vertical motor signal (downward)
Front vertical switch off
Below 1 V
Front vertical switch on (Downward)
11 to 14 V
a4-8 (FRV+) - a4-2 (GND)
B - W-B
Front vertical motor signal (upward)
Front vertical switch off
Below 1 V
Front vertical switch on (Upward)
11 to 14 V
a4-9 (RCL+) - a4-2 (GND)
P - W-B
Reclining motor signal (forward)
Reclining switch off
Below 1 V
Reclining switch on (Forward)
11 to 14 V
a4-11 (RCL-) - a4-2 (GND)
LG - W-B
Reclining motor signal (rearward)
Reclining switch off
Below 1 V
Reclining switch on (Rearward)
11 to 14 V
a4-10 (LFT+) - a4-2 (GND)
V - W-B
Lifter motor signal (upward)
Lifter switch off
Below 1 V
Lifter switch on (Upward)
11 to 14 V
a4-12 (LFT-) - a4-2 (GND)
G - W-B
Lifter motor signal (downward)
Lifter switch off
Below 1 V
Lifter switch on (Downward)
11 to 14 V
a5-1 (SGND) - a4-2 (GND)
BR - W-B
Ground
Always
Below 1 Ω
a5-3 (SSFV) - a5-1 (SGND)
R - BR
Front vertical position signal
Front vertical function operating
4.5 to 4.8 V
a5-4 (SSRL) - a5-1 (SGND)
P - BR
Lifter position signal
Lifter function operating
4.5 to 4.8 V
a5-5 (SSRS) - a5-1 (SGND)
G - BR
Slide position signal
Slide function operating
4.5 to 4.8 V
a5-11 (SSRR) - a5-1 (SGND)
V - BR
Reclining position signal
Reclining function operating
4.5 to 4.8 V
| CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) |


| *A |
for LHD |
*B |
for RHD |
Remove the main body ECU (Click here).
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A-30 (BECU) - Body ground
-
Power source
Always
11 to 14 V
A-32 (IG) - Body ground
-
Power source (IG)
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
A-11 (GND) - Body ground
-
Body ground
Always
Below 1 Ω
G63-3 (GND2) - Body ground
W-B - Body ground
Body ground
Always
Below 1 Ω
Install the main body ECU (Click here).
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G63-25 (M1) - Body ground
SB - Body ground
Memory switch M1 signal
Memory switch M1 off
Pulse generation (See waveform 1 or 2)
Memory switch M1 on
Below 1 V
G63-26 (MM) - Body ground
LG - Body ground
Memory switch SET signal
Memory switch SET off
Pulse generation (See waveform 1 or 2)
Memory switch SET on
Below 1 V
G63-27 (M2) - Body ground
V - Body ground
Memory switch M2 signal
Memory switch M2 off
Pulse generation (See waveform 1 or 2)
Memory switch M2 on
Below 1 V
2I-27 (FLCY) - Body ground*1
R - Body ground
Front door courtesy light switch LH signal
Front door LH closed
11 to 14 V
Front door LH open
Below 1 V
2H-26 (FRCY) - Body ground*2
B - Body ground
Front door courtesy light switch RH signal
Front door RH closed
11 to 14 V
Front door RH open
Below 1 V
- *1: for LHD
- *2: for RHD
- *1: for LHD
Using an oscilloscope, check waveform 1.

Waveform 1 (Reference) Item
Content
Terminal No. (Symbol)
G63-25 (M1) - Body ground
G63-26 (MM) - Body ground
G63-27 (M2) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Memory switch M1 off
Memory switch SET off
Memory switch M2 off
Using an oscilloscope, check waveform 2.

Waveform 2 (Reference) Item
Content
Terminal No. (Symbol)
G63-25 (M1) - Body ground
G63-26 (MM) - Body ground
G63-27 (M2) - Body ground
Tool Setting
5 V/DIV., 20 ms/DIV.
Condition
Memory switch M1 off
Memory switch SET off
Memory switch M2 off