2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0617 Starter Relay Circuit High

Diagnostic trouble codes · Vehicles built from Aug 2013

DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM.
If the ECM detects the starter signal (STA signal) while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.
DTC No.
DTC Detection Condition
Trouble Area
P0617
When conditions (a), (b) and (c) are met, a positive (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):
  1. (a) The vehicle speed is more than 20 km/h (12.4 mph).
  2. (b) The engine speed is more than 1000 rpm.
  3. (c) The STA signal is on.
  1. Short in starter signal circuit
  2. Clutch start switch assembly*1
  3. Park/neutral position switch assembly*2
  4. Ignition switch assembly
  5. ECM
  1. *1: for Manual Transmission
  2. *2: for Automatic Transmission

WIRING DIAGRAM

A311895E01
A311896E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.
    If the engine does not crank, proceed to Problem Symptoms Table (Click here).
  2. Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. CHECK IF VEHICLE IS EQUIPPED WITH ENTRY AND START SYSTEM
  1. Confirm the entry and start system.

    Result 
    Result
    Proceed to
    w/o Entry and Start System
    A
    w/ Entry and Start System
    B



B
Go to step 11
A


2. READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.

    OK:
    Condition
    Starter Signal
    Ignition switch ON
    OFF
    Engine started
    ON

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Manual Transmission)
    B
    NG (for Automatic Transmission)
    C



B
Go to step 3

C
Go to step 7
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. INSPECT IGNITION SWITCH ASSEMBLY

  1. B119736E13
    Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Any terminals
    LOCK
    10 kΩ or higher
    2 (AM1) - 1 (ST1)
    START
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Ignition Switch Assembly)

  1. Reconnect the ignition switch assembly connector.



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - CLUTCH START SWITCH ASSEMBLY)
  1. Disconnect the clutch start switch assembly connector.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G2-1 (ST1) or A41-2 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the clutch start switch assembly connector.

  1. Reconnect the ignition switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - STARTER RELAY [ST])
  1. Disconnect the clutch start switch assembly connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 or A41-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the clutch start switch assembly connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch assembly connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-1 or G60-8 (STA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the clutch start switch assembly connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

7. INSPECT IGNITION SWITCH ASSEMBLY

  1. B119736E13
    Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Any terminals
    LOCK
    10 kΩ or higher
    2 (AM1) - 1 (ST1)
    START
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Ignition Switch Assembly)

  1. Reconnect the ignition switch assembly connector.



NG
REPLACE IGNITION SWITCH ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the ignition switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G2-1 (ST1) or C40-4 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the ignition switch assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY [ST])
  1. Disconnect the park/neutral position switch connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 or C40-5 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the ECM connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C40-5 or G60-8 (STA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the ECM connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

11. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

  1. Read the value displayed on the tester when the ignition switch is turned to ON and when the engine is started.

    OK:
    Condition
    Starter Signal
    Ignition switch ON
    OFF
    Engine started
    ON

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Manual Transmission)
    B
    NG (for Automatic Transmission)
    C



B
Go to step 12

C
Go to step 15
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)

12. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the clutch start switch assembly connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A41-2 or G50-3 (STAR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the clutch start switch assembly connector.

  1. Reconnect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - STARTER RELAY [ST])
  1. Disconnect the clutch start switch assembly connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 or A41-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the clutch start switch assembly connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ECM)
  1. Disconnect the ECM connector.

  1. Disconnect the clutch start switch assembly connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A41-1 or G60-8 (STA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the clutch start switch assembly connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM

15. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - POWER MANAGEMENT CONTROL ECU)
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the power management control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    C40-4 or G50-3 (STAR) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the power management control ECU connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - STARTER RELAY [ST])
  1. Disconnect the park/neutral position switch connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Starter relay (ST) terminal 1 or C40-5 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)
  1. Disconnect the park/neutral position switch connector.

  1. Disconnect the ECM connector.

  1. Remove the starter relay (ST) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C40-5 or G60-8 (STA) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the park/neutral position switch connector.

  1. Reconnect the ECM connector.

  1. Reinstall the starter relay (ST).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM


← P0604 Random Access Memory (RAM) (+ 7 more codes) (from Aug 2013)P0630 VIN not Programmed or Mismatch - ECM / PCM (from Aug 2014) →