2013-2015 Land Cruiser Prado · Service Manual Vehicle Interior

All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the multiplex network master switch, and key-linked switch signals from the front door lock. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B243233E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Since the power door lock control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


1. CHECK DOOR LOCK OPERATION
  1. Check the door lock operation.

    Result 
    Result
    Proceed to
    No doors can be locked using multiplex network master switch
    A
    No doors can be locked using key-linked switch
    B



B
Go to step 2
A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)

2. READ VALUE USING INTELLIGENT TESTER (KEY-LINKED SWITCH)
  1. Use the Data List to check if the door key-linked switches is functioning properly (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Door Key SW-Lock
    Driver side door key-linked switch lock signal / ON or OFF
    ON: Driver side door key cylinder turned to lock position
    OFF: Driver side door key cylinder not turned to lock position
    -
    D Door Key SW-UL
    Driver side door key-linked switch unlock signal / ON or OFF
    ON: Driver side door key cylinder turned to unlock position
    OFF: Driver side door key cylinder not turned to unlock position
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)

3. INSPECT FRONT DOOR LOCK ASSEMBLY (KEY-LINKED SWITCH)
  1. Remove the front door lock (Click here).

  1. Measure the resistance according to the value(s) in the table below.B245138E01

    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Off
    -
    -
    V100135
    Lock
    V100136
    Unlock

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    9 (L) - 7 (E)
    Lock
    Below 1 Ω
    9 (L) - 7 (E)
    Off
    10 kΩ or higher
    10 (UL) - 7 (E)
    Unlock
    Below 1 Ω
    10 (UL) - 7 (E)
    Off
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    6 (L) - 8 (E)
    Lock
    Below 1 Ω
    6 (L) - 8 (E)
    Off
    10 kΩ or higher
    5 (UL) - 8 (E)
    Unlock
    Below 1 Ω
    5 (UL) - 8 (E)
    Off
    10 kΩ or higher



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
  1. Disconnect the K6*1 and J6*2 door lock connectors.

    1. *1: for LHD
    2. *2: for RHD

  1. Remove the G46 main body ECU (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    K6-10 (UL) - G64-24 (UL3)
    Always
    Below 1 Ω
    K6-9 (L) - G64-11 (L2)
    Always
    Below 1 Ω
    K6-7 (E) - Body ground
    Always
    Below 1 Ω
    K6-10 (UL) - Body ground
    Always
    10 kΩ or higher
    K6-9 (L) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    J6-5 (UL) - G64-24 (UL3)
    Always
    Below 1 Ω
    J6-6 (L) - G64-11 (L2)
    Always
    Below 1 Ω
    J6-8 (E) - Body ground
    Always
    Below 1 Ω
    J6-5 (UL) - Body ground
    Always
    10 kΩ or higher
    J6-6 (L) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)


← All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder (Aug 2013 – Jul 2014)PRECAUTION (from Aug 2013) →